Skip to contentSkip to conversation

nm256 [was: ALSA: doc notes additions]

DISCUSSION Patrick Shirkey 2 participants 2 messages Sep 2, 2002 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): [email protected]

#1 lore raw

A person who unfortunately did not provide an email address has submitted this for the alsa-docs.

Quoted 10 lines

I use this driver on a Dell Latitude CPi laptop.
I confirm that the driver hangs 99% of the time when loaded normally. However I have found a way to raise chances to load correctly:
1: boot single-user
2: if you use journaling-less filesystems (such as ext2), remount
the big ones read-only to save you checking time in case of crash.
3: load the AC97 part of the driver:
modprobe snd-ac97-codec
4: start X11 (I personnally use XF86 4.2.0) typically using "startx"
and terminate the session immediately, to return to the console.

Quoted 9 lines

5: load the remaining part of the driver:
modprobe snd-nm256
6: if it doesn't crash, you can restore settings with
"alsactl restore", then remount your filesystems read-write, then proceed with normal boot procedure (exit the single-user shell).
With this procedure I avoid crashing 25-33% of time (i.e. it crashes 2 or 3 times before it succeeds). Hope this helps.

This seems more like a bug than a quirk of the card. Is it worth adding it to the notes or can the problem be fixed?

Signature · 12 lines
Patrick Shirkey - Boost Hardware Ltd.
For the discerning hardware connoisseur
Http://www.boosthardware.com
Http://www.boosthardware.com/LAU/guide/
========================================



-------------------------------------------------------
This sf.net email is sponsored by: OSDN - Tired of that same old
cell phone?  Get a new here for FREE!
https://www.inphonic.com/r.asp?r=sourceforge1&refcode1=vs3390
#2 lore raw

At Mon, 02 Sep 2002 22:06:34 +0900,

Quoted 24 lines · Patrick Shirkey

A person who unfortunately did not provide an email address has submitted this for the alsa-docs.

Quoted 10 lines

I use this driver on a Dell Latitude CPi laptop.
I confirm that the driver hangs 99% of the time when loaded normally. However I have found a way to raise chances to load correctly:
1: boot single-user
2: if you use journaling-less filesystems (such as ext2), remount
the big ones read-only to save you checking time in case of crash.
3: load the AC97 part of the driver:
modprobe snd-ac97-codec
4: start X11 (I personnally use XF86 4.2.0) typically using "startx"
and terminate the session immediately, to return to the console.

Quoted 9 lines

5: load the remaining part of the driver:
modprobe snd-nm256
6: if it doesn't crash, you can restore settings with
"alsactl restore", then remount your filesystems read-write, then proceed with normal boot procedure (exit the single-user shell).
With this procedure I avoid crashing 25-33% of time (i.e. it crashes 2 or 3 times before it succeeds). Hope this helps.

Quoted 2 lines

This seems more like a bug than a quirk of the card. Is it worth adding it to the notes or can the problem be fixed?

a newer version (rc3) should be more stabler than before, although it still crashes sometimes.
as far as i investigated, the crash is involved with two things:

1. crash during probing the ac97 codec capability.

touching ac97 registers soon after reset seems dangerous. this danger is lowered now but still might happen.

2. crash in chip_init().

this seems to happen after some reboots. crashes randomly. no idea what happens and how to avoid.

Takashi

-------------------------------------------------------
This sf.net email is sponsored by: OSDN - Tired of that same old cell phone? Get a new here for FREE!
https://www.inphonic.com/r.asp?r=sourceforge1&refcode1=vs3390