Skip to contentSkip to conversation

P4 with i845E not booting with 2.4.19 / 3.5.31

DISCUSSION Justin Heesemann 3 participants 6 messages Sep 2, 2002 – Sep 9, 2002

lore
Share & tools
lore
#0 lore raw
Quoted 5 lines

I tested:
2.4.19-pre6 -> boots with mem=512M parameter
2.4.19-pre7 -> didn't boot at all
2.4.19-pre7 with arch/i386/kernel/setup.c from 2.4.19-pre6 -> boots with mem=512M parameter

I have another update:
some might know the memtest86 utility.

it has three ways of detecting the memory size "BIOS - Std", "BIOS - All" and "Probe"

on my Athlon Mainboard (which has no Problems with 2.4.19 or later kernels) all methods show the same (or nearly same) ammount of memory.

on my Epox 4G4A+ i845g Mainboard, which has all the Problems Jens Wiesecke has, it's different:
BIOS - Std : 640k (!!)
BIOS - All : 4091M (!!!!)
Probe : 511M (which seems correct as I have 512 MB Ram and 1 MB is shared
graphics ram)

Signature · 3 lines
Best Regards

Justin Heesemann
#1 lore raw
Quoted 10 lines · Justin Heesemann
Quoted 5 lines

I tested:
2.4.19-pre6 -> boots with mem=512M parameter
2.4.19-pre7 -> didn't boot at all
2.4.19-pre7 with arch/i386/kernel/setup.c from 2.4.19-pre6 -> boots with mem=512M parameter

I have another update:
some might know the memtest86 utility.

Quoted 8 lines

it has three ways of detecting the memory size "BIOS - Std", "BIOS - All" and "Probe"

on my Athlon Mainboard (which has no Problems with 2.4.19 or later kernels) all methods show the same (or nearly same) ammount of memory.

on my Epox 4G4A+ i845g Mainboard, which has all the Problems Jens Wiesecke has, it's different:
BIOS - Std : 640k (!!)
BIOS - All : 4091M (!!!!)
Probe: 511M (which seems correct as I have 512 MB Ram and 1 MB is shared graphics ram)

ok. I tested my Chaintech 9EJL i845E mainboard the same way and I have exactly the same output with memtest86

BIOS - Std : 640k
BIOS - All : 4091M (memtest stops working afterwards)
Probe: 512M (since I have no shared graphics ram)

so the problem seems to be BIOS related. But what I don't understand is that since I tell the kernel to use 512 MByte of RAM (mem=512M) and kernels up to 2.4.19pre6 can handle this:

What changed and is there a workaround for kernels newer than 2.4.19pre6 (for example telling the kernel not to rely on the memory information of the BIOS e820 procedure) ?

I tried to compile 2.4.20pre5-(ac) with the arch/i386/kernel/setup.c from 2.4.19pre6 but that didn't work.

Best regards

Signature · 4 lines
Jens Wiesecke
Institute for Macromolecular Chemistry
Darmstadt - Germany
e-mail: [email protected]
#2 lore raw
Quoted 10 lines · Jens Wiesecke

so the problem seems to be BIOS related. But what I don't understand is that since I tell the kernel to use 512 MByte of RAM (mem=512M) and kernels up to 2.4.19pre6 can handle this:

What changed and is there a workaround for kernels newer than 2.4.19pre6 (for example telling the kernel not to rely on the memory information of the BIOS e820 procedure) ?

I tried to compile 2.4.20pre5-(ac) with the arch/i386/kernel/setup.c from 2.4.19pre6 but that didn't work.

I don't know. Without a serial console oops dump I don't have time to figure it out either

#3 lore raw
Quoted 9 lines · Alan Cox
Quoted 8 lines · Jens Wiesecke

so the problem seems to be BIOS related. But what I don't understand is that since I tell the kernel to use 512 MByte of RAM (mem=512M) and kernels up to 2.4.19pre6 can handle this:

What changed and is there a workaround for kernels newer than 2.4.19pre6 (for example telling the kernel not to rely on the memory information of the BIOS e820 procedure) ?

Quoted 6 lines
Quoted 2 lines

I tried to compile 2.4.20pre5-(ac) with the arch/i386/kernel/setup.c from 2.4.19pre6 but that didn't work.

I don't know. Without a serial console oops dump I don't have time to figure it out either

when i used the boot option:
mem=exactmap mem=640K@0 mem=510M@1M
i was able to boot the kernel.

however.. when i tried to boot from a 2.4.19 kernel boot cd, it failed with:

here is the dmesg:

Linux version 2.4.20-pre5-ac1 (root@lux) (gcc version 2.95.3 20010315 (release)) #1 Sun Sep 1 17:26:49 Local time zone must be set--see zic manua BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000a0000 - 000000001fef0000 (reserved)
BIOS-e820: 000000001fef0000 - 000000001fef3000 (ACPI NVS)
BIOS-e820: 000000001fef3000 - 000000001ff00000 (ACPI data)
user-defined physical RAM map:
user: 0000000000000000 - 00000000000a0000 (usable)
user: 0000000000100000 - 000000001ff00000 (usable)
511MB LOWMEM available.
On node 0 totalpages: 130816
zone(0): 4096 pages.
zone(1): 126720 pages.
zone(2): 0 pages.
Kernel command line: auto BOOT_IMAGE=test ro root=304 mem=exactmap mem=640k@0 mem=510M@1M console=ttyS0,9600n8
Initializing CPU#0
Detected 2019.977 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 4023.91 BogoMIPS
Memory: 514460k/523264k available (1052k kernel code, 8420k reserved, 421k data, 60k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode cache hash table entries: 32768 (order: 6, 262144 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes)
ramfs: mounted with options: <defaults>
ramfs: max_pages=64307 max_file_pages=0 max_inodes=0 max_dentries=64307 Buffer cache hash table entries: 32768 (order: 5, 131072 bytes) Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000 Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.

CPU:     After generic, caps: 3febfbff 00000000 00000000 00000000
CPU:             Common caps: 3febfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 04

Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xfae70, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI: Found IRQ 10 for device 00:1f.1
PCI: Sharing IRQ 10 with 00:02.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch ([email protected])
devfs: boot_options: 0x0
Installing knfsd (copyright (C) 1996 [email protected]).
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha1
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 00:1f.1
PCI: Device 00:1f.1 not available because of resource collisions
PCI: Found IRQ 10 for device 00:1f.1
PCI: Sharing IRQ 10 with 00:02.0
ICH4: Not fully BIOS configured!
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later

    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio

hda: ST380020A, ATA DISK drive
hdc: SAMSUNG CD-ROM SC-152L, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.12
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
8139too Fast Ethernet driver 0.9.26
PCI: Found IRQ 11 for device 01:04.0
eth0: RealTek RTL8139 Fast Ethernet at 0xe0804000, 00:04:61:42:29:5a, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 60k freed
Adding Swap: 498004k swap-space (priority -1)
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.

However.. when i tried to boot from a 2.4.19 boot cd (same boot option as above) it only got as far as

read_super_block: can't find a reiserfs filesystem on (dev 01:00, block 64, size 1024)
read_super_block: can't find a reiserfs filesystem on (dev 01:00, block 8, size 1024)
XFS: bad magic number
XFS: SB validate failed

Kernel panic: VFS: Unable to mount root fs on 01:00
Signature · 2 lines
Best Regards,
Justin Heesemann
#4 lore raw
Quoted 3 lines · Justin Heesemann
Quoted 2 lines · Alan Cox

I don't know. Without a serial console oops dump I don't have time to figure it out either

seems like serial console doesn't dump anything in my case.

Quoted 10 lines

when i used the boot option:
mem=exactmap mem=640K@0 mem=510M@1M
i was able to boot the kernel.

however.. when i tried to boot from a 2.4.19 kernel boot cd, it failed with:

here is the dmesg:

Quoted 11 lines

Linux version 2.4.20-pre5-ac1 (root@lux) (gcc version 2.95.3 20010315 (release)) #1 Sun Sep 1 17:26:49 Local time zone must be set--see zic manua BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000a0000 - 000000001fef0000 (reserved)
BIOS-e820: 000000001fef0000 - 000000001fef3000 (ACPI NVS)
BIOS-e820: 000000001fef3000 - 000000001ff00000 (ACPI data)
user-defined physical RAM map:
user: 0000000000000000 - 00000000000a0000 (usable)
user: 0000000000100000 - 000000001ff00000 (usable)
511MB LOWMEM available.

i tried again with a 2.2 kernel. they don't seem to require _any_ mem=xxx parameters to work so i checked dmesg:

Linux version 2.2.20-idepci (herbert@gondolin) (gcc version 2.7.2.3) #1 Sat

Apr 20 12:45:19 EST 2002

BIOS-provided physical RAM map:
BIOS-e820: 0009f000 @ 00000000 (usuable)
BIOS-e820: 1fdf0000 @ 00100000 (usuable)
Detected 2019977 kHz processor.

This is the same computer, same RAM, same Bios.
how comes e820 provides these different results ?

--
Best Regards
Justin

#5 lore raw
Quoted 7 lines · Justin Heesemann
Quoted 5 lines · Alan Cox
Quoted 3 lines

I don't know. Without a serial console oops dump I don't have time to figure it out either

seems like serial console doesn't dump anything in my case.

I can confirm that the serial console doesn't send any Byte of information before the boot process hangs.

I tried several times over the weekend and it doesn't matter which kernel newer than 2.4.19pre7 I tried.

Quoted 9 lines
Quoted 9 lines

when i used the boot option:
mem=exactmap mem=640K@0 mem=510M@1M
i was able to boot the kernel.

however.. when i tried to boot from a 2.4.19 kernel boot cd, it failed with:

here is the dmesg:

Quoted 11 lines
Quoted 11 lines

Linux version 2.4.20-pre5-ac1 (root@lux) (gcc version 2.95.3 20010315 (release)) #1 Sun Sep 1 17:26:49 Local time zone must be set--see zic manua BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000a0000 - 000000001fef0000 (reserved)
BIOS-e820: 000000001fef0000 - 000000001fef3000 (ACPI NVS)
BIOS-e820: 000000001fef3000 - 000000001ff00000 (ACPI data) user-defined physical RAM map:
user: 0000000000000000 - 00000000000a0000 (usable)
user: 0000000000100000 - 000000001ff00000 (usable)
511MB LOWMEM available.

I tried 2.4.18-3 from RedHat 7.3 with mem=exactmap mem=640K@0 mem=511M@1M (since I have no shared memory) and got (no APIC):

Linux version 2.4.18-3 ([email protected]) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110)) #1 Thu Apr 18 07:37:53 EDT 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000a0000 - 000000001fff0000 (reserved)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
user-defined physical RAM map:
user: 0000000000000000 - 00000000000a0000 (usable)
user: 0000000000100000 - 0000000020000000 (usable)

but if I boot with plain 2.4.18 with mem=512M (with local APIC) I got:

Linux version 2.4.18 ([email protected]) (gcc version 2.95.4 20011006 (Debian prerelease)) #7 Sat Aug 31 12:18:39 CEST 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000a0000 - 000000001fff0000 (reserved)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
found SMP MP-table at 000f5c40
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.

the e820 routine seems to provide the same RAM map but 2.4.18 recognizes that several pages are reserved twice - since I'm no kernel guy at all: does this behaviour indicate any problem 2.4.19 might have with my (and Justin's) BIOS ?

Quoted 11 lines

i tried again with a 2.2 kernel. they don't seem to require _any_ mem=xxx parameters to work so i checked dmesg:

Linux version 2.2.20-idepci (herbert@gondolin) (gcc version 2.7.2.3) #1 Sat Apr 20 12:45:19 EST 2002 BIOS-provided physical RAM map:
BIOS-e820: 0009f000 @ 00000000 (usuable)
BIOS-e820: 1fdf0000 @ 00100000 (usuable)
Detected 2019977 kHz processor.

This is the same computer, same RAM, same Bios.
how comes e820 provides these different results ?

I don't have any dmesg here but I can confirm that 2.2 series kernels don't need a mem=xxx boot parameter at all (on my board).

I added both dmesg files.

Best regrads

Signature · 4 lines
Jens Wiesecke
Institute for Macromolecular Chemistry
Darmstadt - Germany
e-mail: [email protected]

Linux version 2.4.18-3 ([email protected]) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-110)) #1 Thu Apr 18 07:37:53 EDT 2002 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000a0000 - 000000001fff0000 (reserved)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
user-defined physical RAM map:
user: 0000000000000000 - 00000000000a0000 (usable)
user: 0000000000100000 - 0000000020000000 (usable)
On node 0 totalpages: 131072
zone(0): 4096 pages.
zone(1): 126976 pages.
zone(2): 0 pages.
Kernel command line: ro root=/dev/hda10 hdc=ide-scsi mem=exactmap mem=640k@0 mem=511M@1M
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1614.986 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3224.37 BogoMIPS
Memory: 514172k/524288k available (1119k kernel code, 9732k reserved, 775k data, 280k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.

CPU:     After generic, caps: 3febfbff 00000000 00000000 00000000
CPU:             Common caps: 3febfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 1.60GHz stepping 04

Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb0c0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI: Found IRQ 10 for device 00:1f.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Starting kswapd
VFS: Diskquotas version dquot_6.5.0 initialized
Detected PS/2 Mouse Port.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
block: 992 slots per queue, batch=248
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24cb
PCI: Device 00:1f.1 not available because of resource collisions
PCI_IDE: (ide_setup_pci_device:) Could not enable device.
hda: MAXTOR 6L060J3, ATA DISK drive
hdc: CD-RW CDR-5S40, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 117266688 sectors (60041 MB) w/1819KiB Cache, CHS=7299/255/63
ide-floppy driver 0.99.newide
hdd: No disk in drive
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 280k freed
Adding Swap: 136512k swap-space (priority -1)
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 07:43:07 Apr 18 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xd800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 12
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device 2 (vend/prod 0x5cc/0x2267) is not claimed by any active driver. hub.c: USB new device connect on bus2/1, assigned device number 2
hub.c: USB hub found
hub.c: 5 ports detected
hub.c: USB new device connect on bus2/1/2, assigned device number 3
usb.c: USB device 3 (vend/prod 0x46d/0xc00b) is not claimed by any active driver. hub.c: USB new device connect on bus2/1/4, assigned device number 4
usb.c: USB device 4 (vend/prod 0x46a/0x1) is not claimed by any active driver.
usb.c: registered new driver acm
usb.c: registered new driver hiddev
ttyACM0: USB ACM device
acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters CDCEther.c: CDCEther.c: v0.98.5 22 Sep 2001 Brad Hards and another
usb.c: registered new driver CDCEther
usb.c: registered new driver hid
input0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb2:3.0
input1: USB HID v1.00 Keyboard [046a:0001] on usb2:4.0
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]>
hid-core.c: USB HID support drivers
usb-uhci.c: ENXIO 84000380, flags 0, urb df578460, burb df578360
usb-uhci.c: ENXIO 84000380, flags 0, urb df578460, burb df578360
usb-uhci.c: ENXIO 80000280, flags 0, urb df578560, burb df578460
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 18 ret -6
usb-uhci.c: ENXIO 84000380, flags 0, urb df578460, burb df578360
usb-uhci.c: ENXIO 84000380, flags 0, urb df578460, burb df578360
usb-uhci.c: ENXIO 80000280, flags 0, urb df578560, burb df578460
usbdevfs: USBDEVFS_CONTROL failed dev 2 rqt 128 rq 6 len 18 ret -6
mice: PS/2 mouse device common for all mice
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: CD-RW Model: CDR-5S40 Rev: ZSG4
Type: CD-ROM ANSI SCSI revision: 02
ide-floppy: hdd: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hdd: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
hdd: No disk in drive
ide-floppy: hdd: I/O error, pc = 1e, key = 2, asc = 3a, ascq = 0
ip_conntrack (4096 buckets, 32768 max)
8139too Fast Ethernet driver 0.9.24
PCI: Found IRQ 11 for device 02:07.0
eth0: RealTek RTL8139 Fast Ethernet at 0xe0848000, 00:50:70:f1:03:48, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'

Linux version 2.4.18 ([email protected]) (gcc version 2.95.4 20011006 (Debian prerelease)) #7 Sat Aug 31 12:18:39 CEST 2002 BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000a0000 - 000000001fff0000 (reserved)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
found SMP MP-table at 000f5c40
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131072
zone(0): 4096 pages.
zone(1): 126976 pages.
zone(2): 0 pages.
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Unknown CPU [15:2] APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 1
Kernel command line: lang= devfs=nomount ramdisk_size=8192 mem=512M BOOT_IMAGE=vmlinuz auto
Initializing CPU#0
Detected 1630.971 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3224.37 BogoMIPS
Memory: 513484k/524288k available (1302k kernel code, 10416k reserved, 431k data, 216k init, 0k highmem) Dentry-cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: Before vendor init, caps: 3febfbff 00000000 00000000, vendor = 0
CPU: L1 I cache: 12K, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: After vendor init, caps: 3febfbff 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.

CPU:     After generic, caps: 3febfbff 00000000 00000000 00000000
CPU:             Common caps: 3febfbff 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 1.60GHz stepping 04

Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-12, 2-20, 2-21 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 21.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178020

.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0020

.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:

 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 000 00  1    0    0   0   0    0    0    00
 06 001 01  0    0    0   0   0    1    1    51
 07 001 01  0    0    0   0   0    1    1    59
 08 001 01  0    0    0   0   0    1    1    61
 09 001 01  0    0    0   0   0    1    1    69
 0a 000 00  1    0    0   0   0    0    0    00
 0b 000 00  1    0    0   0   0    0    0    00
 0c 000 00  1    0    0   0   0    0    0    00
 0d 001 01  0    0    0   0   0    1    1    71
 0e 001 01  0    0    0   0   0    1    1    79
 0f 001 01  0    0    0   0   0    1    1    81
 10 001 01  1    1    0   1   0    1    1    89
 11 001 01  1    1    0   1   0    1    1    91
 12 001 01  1    1    0   1   0    1    1    99
 13 001 01  1    1    0   1   0    1    1    A1
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 001 01  1    1    0   1   0    1    1    A9
 17 001 01  1    1    0   1   0    1    1    B1

IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1615.0357 MHz.
..... host bus clock speed is 100.9395 MHz.
cpu: 0, clocks: 1009395, slice: 504697 CPU0<T0:1009392,T1:504688,D:7,S:504697,C:1009395>
mtrr: v1.40 (20010327) Richard Gooch ([email protected])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb0c0, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
Unknown bridge resource 2: assuming transparent
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 16
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I7,P0) -> 22
PCI->APIC IRQ transform: (B2,I9,P0) -> 18
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
Starting kswapd
NTFS driver v1.1.22 [Flags: R/O]
ACPI: APM is already active, exiting
parport0: PC-style at 0x378 (0x778) [PCSPP(,...)]
parport0: irq 7 detected
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
lp0: using parport0 (polling).
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PCI_IDE: unknown IDE controller on PCI bus 00 device f9, VID=8086, DID=24cb
PCI: Device 00:1f.1 not available because of resource collisions
PCI_IDE: chipset revision 1
PCI_IDE: not 100% native mode: will probe irqs later

    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio

keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
hda: MAXTOR 6L060J3, ATA DISK drive
hdc: CD-RW CDR-5S40, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 117266688 sectors (60041 MB) w/1819KiB Cache, CHS=7299/255/63
hdc: ATAPI 48X CD-ROM CD-R/RW drive, 1984kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.12
ide-floppy driver 0.97.sv
hdd: No disk in drive
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm Partition check:
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
PPP generic driver version 2.4.1
PPP Deflate Compression module registered
8139too Fast Ethernet driver 0.9.24
eth0: RealTek RTL8139 Fast Ethernet at 0xe0800000, 00:50:70:f1:03:48, IRQ 22
eth0: Identified 8139 chip type 'RTL-8139C'
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 440M
agpgart: Detected Intel i845 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
[drm] AGP 0.99 on Intel i845 @ 0xe0000000 64MB
[drm] Initialized mga 3.0.2 20010321 on minor 0
ide-floppy driver 0.97.sv
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Setting latency timer of device 00:1d.0 to 64
uhci.c: USB UHCI at I/O 0xd800, IRQ 16
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
uhci.c: USB UHCI at I/O 0xd000, IRQ 19
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
uhci.c: USB UHCI at I/O 0xd400, IRQ 18
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hid
hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <[email protected]> hid-core.c: USB HID support drivers
usb.c: registered new driver acm
acm.c: v0.21:USB Abstract Control Model driver for USB modems and ISDN adapters
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 216k freed
hub.c: USB new device connect on bus1/1, assigned device number 2 Adding Swap: 136512k swap-space (priority -1)
attempt to access beyond end of device
03:02: rw=0, want=2, limit=1
EXT2-fs: unable to read superblock
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
FAT: Did not find valid FSINFO signature.
Found signature1 0x4e0005 signature2 0xc00b6600 sector=1.
VFS: Can't find a valid FAT filesystem on dev 03:01.
ide-floppy: hdd: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hdd: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
hdd: No disk in drive
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
ttyACM0: USB ACM device
hub.c: USB new device connect on bus2/1, assigned device number 2 hub.c: USB hub found
hub.c: 5 ports detected
hub.c: USB new device connect on bus2/1/2, assigned device number 3
input0: USB HID v1.10 Mouse [Logitech USB Mouse] on usb2:3.0 hub.c: USB new device connect on bus2/1/4, assigned device number 4
input1: USB HID v1.00 Keyboard [046a:0001] on usb2:4.0