Skip to contentSkip to conversation

init script with hotplug & usb audio

DISCUSSION Duncan Sands 3 participants 9 messages Sep 26, 2002 – Oct 1, 2002

lore
Share & tools
lore
#0 lore raw

I have a usb webcam with audio plugged into my computer, and a cs46xx sound card inside.

When I boot the following sequence occurs:

(1) the hotplug subsytem is started. This automatically loads the snd-usb-audio module and the modules it depends on. In particular /proc/asound/ is created.

(2) the alsasound init script is run. It detects that /proc/asound/ exists, and exits at once. In particular it does not restore mixer levels for the cs46xx card.

I solved this by commenting out the check for /proc/asound/ in the init script. The problem goes deeper though, especially when things like usb audio devices are around, which can be
hotplugged: maybe sound card modules should really be calling the hotplug subsystem when they are initialize. The hotplug script would then restore mixer settings etc...

Thoughts?

Duncan.

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#1 lore raw
Quoted 7 lines · Duncan Sands

(1) the hotplug subsytem is started. This automatically loads the snd-usb-audio module and the modules it depends on. In particular /proc/asound/ is created.

(2) the alsasound init script is run. It detects that /proc/asound/ exists, and exits at once. In particular it does not restore mixer levels for the cs46xx card.

you can change the order in which init scripts are run, read your distribution's documentation. on debian, this would mean renaming one of /etc/rc2.d/SXXalsasound or /etc/rc2.d/SXXhotplug -- XX are two-digit numbers that decide over the running order, the higher the later.

hth, tim

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek Welcome to geek heaven.
http://thinkgeek.com/sf

#2 lore raw
Quoted 9 lines · Tim Goetze
Quoted 7 lines · Duncan Sands

(1) the hotplug subsytem is started. This automatically loads the snd-usb-audio module and the modules it depends on. In particular /proc/asound/ is created.

(2) the alsasound init script is run. It detects that /proc/asound/ exists, and exits at once. In particular it does not restore mixer levels for the cs46xx card.

Quoted 5 lines

you can change the order in which init scripts are run, read your distribution's documentation. on debian, this would mean renaming one of /etc/rc2.d/SXXalsasound or /etc/rc2.d/SXXhotplug -- XX are two-digit numbers that decide over the running order, the higher the later.

Sure. On the other hand, if I plug in the usb audio device after the init script has been run, who will restore mixer settings for it? In short, the solution you suggest will work fine in most cases, but in the long term more cooperation between the init script and hotplugging scripts will be needed.

All the best,

Duncan.

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#3 lore raw
In reply to Duncan Sands

At Thu, 26 Sep 2002 10:20:25 +0200,

Quoted 14 lines · Duncan Sands

I have a usb webcam with audio plugged into my computer, and a cs46xx sound card inside.

When I boot the following sequence occurs:

(1) the hotplug subsytem is started. This automatically loads the snd-usb-audio module and the modules it depends on. In particular /proc/asound/ is created.

(2) the alsasound init script is run. It detects that /proc/asound/ exists, and exits at once. In particular it does not restore mixer levels for the cs46xx card.

Quoted 8 lines

I solved this by commenting out the check for /proc/asound/ in the init script. The problem goes deeper though, especially when things like usb audio devices are around, which can be
hotplugged: maybe sound card modules should really be calling the hotplug subsystem when they are initialize. The hotplug script would then restore mixer settings etc...

Thoughts?

i solved like the following:

- add snd-usb-* (and oss audio module) to hotplug's blacklist to avoid to load them from the modules.usermap.
- add a usermap for the usb audio devices to call its own start-up script. the script starts the alsasound init script inside before loading the snd-usb-audio module (if no /proc/asound exists), so that it asssures that the normal PCI devices are assigned prior to usb devices.

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#4 lore raw
Quoted 25 lines · Takashi Iwai
Quoted 13 lines · Duncan Sands

I have a usb webcam with audio plugged into my computer, and a cs46xx sound card inside.

When I boot the following sequence occurs:

(1) the hotplug subsytem is started. This automatically loads the snd-usb-audio module and the modules it depends on. In particular /proc/asound/ is created.

(2) the alsasound init script is run. It detects that /proc/asound/ exists, and exits at once. In particular it does not restore mixer levels for the cs46xx card.

Quoted 8 lines

I solved this by commenting out the check for /proc/asound/ in the init script. The problem goes deeper though, especially when things like usb audio devices are around, which can be
hotplugged: maybe sound card modules should really be calling the hotplug subsystem when they are initialize. The hotplug script would then restore mixer settings etc...

Thoughts?

i solved like the following:

Quoted 7 lines

- add snd-usb-* (and oss audio module) to hotplug's blacklist to avoid to load them from the modules.usermap.
- add a usermap for the usb audio devices to call its own start-up script. the script starts the alsasound init script inside before loading the snd-usb-audio module (if no /proc/asound exists), so that it asssures that the normal PCI devices are assigned prior to usb devices.

Thanks for the info. I still think it's a bandaid though: the real problem is that the logic in the init script is broken. Anything that causes modules to be loaded before the init script is run breaks the script, as far as I can see. For example: compiling into the kernel, i.e. not as modules ; using hardware detection software that autoloads sound card drivers ; using usb audio... In these cases /proc/asound will exist when the init script is run, and mixer settings will not be restored, card specific scripts will not be run etc.

In the long term (2.6 kernel) I am imagining the following:

(1) the init script just loads modules.
(2) when modules are loaded, whether for a pci card, a usb one whatever, the hotplug subsystem is called: it restores mixer settings for the card and runs card specific scripts.

In the short term a quick hack will do of course.

Thanks for your help,

Duncan.

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#5 lore raw

At Fri, 27 Sep 2002 09:08:41 +0200,

Quoted 43 lines · Duncan Sands
Quoted 25 lines · Takashi Iwai
Quoted 13 lines · Duncan Sands

I have a usb webcam with audio plugged into my computer, and a cs46xx sound card inside.

When I boot the following sequence occurs:

(1) the hotplug subsytem is started. This automatically loads the snd-usb-audio module and the modules it depends on. In particular /proc/asound/ is created.

(2) the alsasound init script is run. It detects that /proc/asound/ exists, and exits at once. In particular it does not restore mixer levels for the cs46xx card.

Quoted 8 lines

I solved this by commenting out the check for /proc/asound/ in the init script. The problem goes deeper though, especially when things like usb audio devices are around, which can be
hotplugged: maybe sound card modules should really be calling the hotplug subsystem when they are initialize. The hotplug script would then restore mixer settings etc...

Thoughts?

i solved like the following:

Quoted 7 lines

- add snd-usb-* (and oss audio module) to hotplug's blacklist to avoid to load them from the modules.usermap.
- add a usermap for the usb audio devices to call its own start-up script. the script starts the alsasound init script inside before loading the snd-usb-audio module (if no /proc/asound exists), so that it asssures that the normal PCI devices are assigned prior to usb devices.

Thanks for the info. I still think it's a bandaid though: the real problem is that the logic in the init script is broken. Anything that causes modules to be loaded before the init script is run breaks the script, as far as I can see. For example: compiling into the kernel, i.e. not as modules ; using hardware detection software that autoloads sound card drivers ; using usb audio... In these cases /proc/asound will exist when the init script is run, and mixer settings will not be restored, card specific scripts will not be run etc.

Quoted 6 lines

In the long term (2.6 kernel) I am imagining the following:

(1) the init script just loads modules.
(2) when modules are loaded, whether for a pci card, a usb one whatever, the hotplug subsystem is called: it restores mixer settings for the card and runs card specific scripts.

except for the check of /proc/asound, the hotplug problem can be sorted to the following:

1. hotplug may be called before alsa init script.

2. hotplug needs to manage the mixer configuration of plugged / unplugged devices dynamically.

3. alsa initscript itself should be independent from hotplug.

they are not all but certainly a major part of the problems.

the first one is not easy, because the network devices can belong to hotplug, too. the scenario is like this:
many alsa files are located under /usr

    -> a networkfs (e.g. NFS) is required before the alsa service
      -> the network must be initialized in prior
        -> the network base = hotplug is needed to run before alsa!

the second problem is also tough.
alsa driver needs to access the device to get the current mixer values, but at the remove callback of hotplug, the device was actually unplugged... probably implementing cache would be necessary.

the third one is obvious.
i don't think it's good to let hotplug initialize the pci cards, too. for example, if i don't have any usb devices, i'd like to remove hotplug. but if alsa initscript rely on the hotplug stuff, i cannot do that. that's bad.

well, still many obstacles ahead.
i'd love to see a perfect solution :)

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#6 lore raw
Quoted 16 lines · Takashi Iwai

except for the check of /proc/asound, the hotplug problem can be sorted to the following:

1. hotplug may be called before alsa init script.

2. hotplug needs to manage the mixer configuration of plugged / unplugged devices dynamically.

3. alsa initscript itself should be independent from hotplug.

they are not all but certainly a major part of the problems.

the first one is not easy, because the network devices can belong to hotplug, too. the scenario is like this:
many alsa files are located under /usr

Quoted 8 lines
    -> a networkfs (e.g. NFS) is required before the alsa service
      -> the network must be initialized in prior
        -> the network base = hotplug is needed to run before alsa!

the second problem is also tough.
alsa driver needs to access the device to get the current mixer values, but at the remove callback of hotplug, the device was actually unplugged... probably implementing cache would be necessary.

Another point to keep in mind here, is that a lot of people are now using journaled filesystems, and may just turn off the computer without shutting down. You could say that they deserve what they get, but I'm not so sure. Imagine someone using alsamixer to change mixer settings. They quit alsamixer then turn off the machine. Are they wrong to expect the mixer settings to still be there on reboot? After all, they "saved the settings" when they left alsamixer didn't they?

Quoted 8 lines

the third one is obvious.
i don't think it's good to let hotplug initialize the pci cards, too. for example, if i don't have any usb devices, i'd like to remove hotplug. but if alsa initscript rely on the hotplug stuff, i cannot do that. that's bad.

well, still many obstacles ahead.
i'd love to see a perfect solution :)

Duncan.

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#7 lore raw

At Mon, 30 Sep 2002 09:55:14 +0200,

Quoted 27 lines · Duncan Sands
Quoted 16 lines · Takashi Iwai

except for the check of /proc/asound, the hotplug problem can be sorted to the following:

1. hotplug may be called before alsa init script.

2. hotplug needs to manage the mixer configuration of plugged / unplugged devices dynamically.

3. alsa initscript itself should be independent from hotplug.

they are not all but certainly a major part of the problems.

the first one is not easy, because the network devices can belong to hotplug, too. the scenario is like this:
many alsa files are located under /usr

Quoted 8 lines
    -> a networkfs (e.g. NFS) is required before the alsa service
      -> the network must be initialized in prior
        -> the network base = hotplug is needed to run before alsa!

the second problem is also tough.
alsa driver needs to access the device to get the current mixer values, but at the remove callback of hotplug, the device was actually unplugged... probably implementing cache would be necessary.

Quoted 6 lines

Another point to keep in mind here, is that a lot of people are now using journaled filesystems, and may just turn off the computer without shutting down. You could say that they deserve what they get, but I'm not so sure. Imagine someone using alsamixer to change mixer settings. They quit alsamixer then turn off the machine. Are they wrong to expect the mixer settings to still be there on reboot?

yes. the infromation will be lost.

Quoted 1 line

After all, they "saved the settings" when they left alsamixer didn't they?

no, the setting is on memory, thus not saved when you turn the power off. he can run "alsactl store" manually (or write a equivalent wrapper script for alsamixer) instead.
but this should not be standard, i think.

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#8 lore raw
Quoted 9 lines
Quoted 6 lines

Another point to keep in mind here, is that a lot of people are now using journaled filesystems, and may just turn off the computer without shutting down. You could say that they deserve what they get, but I'm not so sure. Imagine someone using alsamixer to change mixer settings. They quit alsamixer then turn off the machine. Are they wrong to expect the mixer settings to still be there on reboot?

yes. the infromation will be lost.

Quoted 7 lines
Quoted 2 lines

After all, they "saved the settings" when they left alsamixer didn't they?

no, the setting is on memory, thus not saved when you turn the power off. he can run "alsactl store" manually (or write a equivalent wrapper script for alsamixer) instead.
but this should not be standard, i think.

Too costly?

Just to be clear: I know that the mixer information will be lost, I was just trying to point out that the current behaviour is not what people might reasonably expect.

Ciao,

Duncan.

-------------------------------------------------------
This sf.net email is sponsored by: DEDICATED SERVERS only $89! Linux or FreeBSD, FREE setup, FAST network. Get your own server today at http://www.ServePath.com/indexfm.htm