Skip to contentSkip to conversation

playing 4 channels

DISCUSSION Helmut Obertanner 2 participants 4 messages Oct 10, 2002 – Oct 11, 2002 2 messages not in the archive

lore
Share & tools
lore
#0 lore raw

How can i tell my soundcard to play 1 stereochannel on Frontspeakers and another stereochannel on rearspeakers ??
I can set my soundcard to 4 channelmode -> o.k.
I write samples in the following order to the soundbuffer:

LF,RF,LR,RR

but i get L-FRONT and R-FRONT on rear output too, and LR and RR are lost in space.
how could i solve this ?

regards, Helmut
http://funkyou.x4u.de

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#1 lore raw

At Thu, 10 Oct 2002 16:20:31 +0200,

Quoted 3 lines · Helmut Obertanner

How can i tell my soundcard to play 1 stereochannel on Frontspeakers and another stereochannel on rearspeakers ??

what sound card? i cannot tell you otherwise ;)

Quoted 8 lines

I can set my soundcard to 4 channelmode -> o.k.
I write samples in the following order to the soundbuffer:

LF,RF,LR,RR

but i get L-FRONT and R-FRONT on rear output too, and LR and RR are lost in space.
how could i solve this ?

this depends on the card, but in general, you can choose the route via the pcm name. for example, on sb live, you can play two stereo-wav files separately to front and rear speakers like:

% aplay -Dfront foo.wav
% aplay -Drear bar.wav

but the chip can mix up the different streams, so the rear signals may be contaminated from front on a certain mixer set up.

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#3 lore raw
In reply to a message not in the archive

At Thu, 10 Oct 2002 20:12:12 +0200,

Quoted 4 lines · Helmut Obertanner

Am Donnerstag, 10. Oktober 2002 17:14 schrieben Sie:

Quoted 2 lines

At Thu, 10 Oct 2002 16:20:31 +0200,

Quoted 8 lines
Quoted 6 lines
Quoted 2 lines · Helmut Obertanner

How can i tell my soundcard to play 1 stereochannel on Frontspeakers and another stereochannel on rearspeakers ??

what sound card? i cannot tell you otherwise ;)

I currently have a CMedia 8738(Model37),

oh, you had bad luck. the rear output of this chip model is _always_ on the loudest level. it seems like there is no mixer control for it. so the incoming stream must be attenuated in advance.

please read alsa-kernel/Documentation/CMIPCI.txt for more details.

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

#5 lore raw
In reply to a message not in the archive

Hi Helmut,

At Fri, 11 Oct 2002 11:53:42 +0200,

Quoted 3 lines · Helmut Obertanner

how is that with other cards, is the mastervolume also respoonnsible for the rearchannels ???

it depends. the later models of cmipci support 4/6 channels playback via one DMA, i.e. interleaved output. in this case, the output volume is controlled by a master volume.

in the case of SB live, the rear output has different codec without volume controls, but the emu10k1 dsp itself can attenuate the signals inside.

most of other sound chips use AC97 for the rear volume controls. some use the secondary codec, and some use a 4/6 channel-capable codec. in both cases, the "Surround" volume element will be there.

Quoted 9 lines

another problem:
in another thread i want to record, (for the realtime vocoder / FX on microphone)

opening the device fails with: device busy.
i use another pcm_handle for capture.

is it impossible to record while playing ?
or what i'm doing wrong...

the rear output uses the ADC as the secondary DAC. so, you cannot use ADC together with 4 channel outputs. (again, the later models use only one DAC for interleaved 4/6 mode, and it's no problem.)

ciao,

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf