clean up scsi documentation
Subsystems (14)
PATCH 1/2 clean up scsi documentation
Ok, here comes part 2. Not mentioned in the first mail: it makes some minor formatting changes in some comments.
Eike
Documentation/00-INDEX +2 -6
@@ -32,8 +32,6 @@ - info on Mylex DAC960/DAC1100 PCI RAID Controller Driver for Linux README.moxa - release notes for Moxa mutiport serial card. -README.nsp_cs.eng - - info on WorkBiT NinjaSCSI-3/32Bi driver. SAK.txt - info on Secure Attention Keys. SubmittingDrivers
@@ -188,10 +186,8 @@ - directory with info on using Linux on the IBM S390. sh/ - directory with info on porting Linux to a new architecture. -scsi-generic.txt - - info on the sg driver for generic (non-disk/CD/tape) SCSI devices. -scsi.txt - - short blurb on using SCSI support as a module. +scsi/ + - directory with info on Linux scsi support. serial-console.txt - how to set up Linux with a serial line console as the default. sgi-visws.txt
Documentation/scsi/00-INDEX +68 -0
68 lines not on this page · raw message
arch/alpha/Kconfig +1 -1
@@ -794,7 +794,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/arm/Kconfig +1 -1
@@ -1014,7 +1014,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/cris/Kconfig +1 -1
@@ -589,7 +589,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/i386/Kconfig +1 -1
@@ -1298,7 +1298,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/ia64/Kconfig +1 -1
@@ -601,7 +601,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/m68k/Kconfig +8 -8
@@ -731,7 +731,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
@@ -752,7 +752,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called sd_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. Do not compile this driver as a + <file:Documentation/scsi/scsi.txt>. Do not compile this driver as a module if your root file system (the one containing the directory /) is located on a SCSI disk. In this case, do not compile the driver for your SCSI host adapter (below) as a module either.
@@ -781,14 +781,14 @@ If you want to use a SCSI tape drive under Linux, say Y and read the SCSI-HOWTO, available from <http://www.linuxdoc.org/docs.html#howto>, and - <file:drivers/scsi/README.st> in the kernel source. This is NOT for + <file:Documentation/scsi/st.txt> in the kernel source. This is NOT for SCSI CD-ROMs. This driver is also available as a module ( = code which can be inserted in and removed from the running kernel whenever you want). The module will be called st.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config ST_EXTRA_DEVS int "Maximum number of SCSI tapes that can be loaded as modules"
@@ -820,7 +820,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called sr_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config BLK_DEV_SR_VENDOR bool "Enable vendor-specific extensions (for SCSI CDROM)"
@@ -866,13 +866,13 @@ quality digital reader of audio CDs (<http://www.xiph.org/paranoia/>). For other devices, it's possible that you'll have to write the driver software yourself. Please read the file - <file:Documentation/scsi-generic.txt> for more information. + <file:Documentation/scsi/scsi-generic.txt> for more information. If you want to compile this as a module ( = code which can be inserted in and removed from the running kernel whenever you want), say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. The module will be called sg.o. If unsure, - say N. + <file:Documentation/scsi/scsi.txt>. The module will be called sg.o. + If unsure, say N. comment "Some SCSI devices (e.g. CD jukebox) support multiple LUNs" depends on SCSI
arch/mips/Kconfig +1 -1
@@ -904,7 +904,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/mips64/Kconfig +1 -1
@@ -488,7 +488,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/parisc/Kconfig +1 -1
@@ -257,7 +257,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/ppc/Kconfig +1 -1
@@ -1393,7 +1393,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/ppc64/Kconfig +1 -1
@@ -332,7 +332,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/sh/Kconfig +1 -1
@@ -733,7 +733,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
arch/sparc/Kconfig +11 -11
@@ -662,7 +662,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
@@ -683,7 +683,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called sd_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. Do not compile this driver as a + <file:Documentation/scsi/scsi.txt>. Do not compile this driver as a module if your root file system (the one containing the directory /) is located on a SCSI disk. In this case, do not compile the driver for your SCSI host adapter (below) as a module either.
@@ -712,14 +712,14 @@ If you want to use a SCSI tape drive under Linux, say Y and read the SCSI-HOWTO, available from <http://www.linuxdoc.org/docs.html#howto>, and - <file:drivers/scsi/README.st> in the kernel source. This is NOT for - SCSI CD-ROMs. + <file:Documentation/scsi/st.txt> in the kernel source. This is NOT + for SCSI CD-ROMs. This driver is also available as a module ( = code which can be inserted in and removed from the running kernel whenever you want). The module will be called st.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config CHR_DEV_OSST tristate "SCSI OnStream SC-x0 tape support"
@@ -734,7 +734,7 @@ tapes (QIC-157) and can be driven by the standard driver st. For more information, you may have a look at the SCSI-HOWTO <http://www.linuxdoc.org/docs.html#howto> and - <file:drivers/scsi/README.osst> in the kernel source. + <file:Documentation/scsi/osst.txt> in the kernel source. More info on the OnStream driver may be found on <http://linux1.onstream.nl/test/> Please also have a look at the standard st docu, as most of it
@@ -744,7 +744,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called osst.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config BLK_DEV_SR tristate "SCSI CDROM support"
@@ -759,7 +759,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called sr_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config BLK_DEV_SR_VENDOR bool "Enable vendor-specific extensions (for SCSI CDROM)"
@@ -805,13 +805,13 @@ quality digital reader of audio CDs (<http://www.xiph.org/paranoia/>). For other devices, it's possible that you'll have to write the driver software yourself. Please read the file - <file:Documentation/scsi-generic.txt> for more information. + <file:Documentation/scsi/scsi-generic.txt> for more information. If you want to compile this as a module ( = code which can be inserted in and removed from the running kernel whenever you want), say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. The module will be called sg.o. If unsure, - say N. + <file:Documentation/scsi/scsi.txt>. The module will be called sg.o. + If unsure, say N. comment "Some SCSI devices (e.g. CD jukebox) support multiple LUNs" depends on SCSI
arch/sparc64/Kconfig +17 -17
@@ -757,7 +757,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
@@ -778,7 +778,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called sd_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. Do not compile this driver as a + <file:Documentation/scsi/scsi.txt>. Do not compile this driver as a module if your root file system (the one containing the directory /) is located on a SCSI disk. In this case, do not compile the driver for your SCSI host adapter (below) as a module either.
@@ -807,14 +807,14 @@ If you want to use a SCSI tape drive under Linux, say Y and read the SCSI-HOWTO, available from <http://www.linuxdoc.org/docs.html#howto>, and - <file:drivers/scsi/README.st> in the kernel source. This is NOT for - SCSI CD-ROMs. + <file:Documentation/scsi/st.txt> in the kernel source. This is NOT + for SCSI CD-ROMs. This driver is also available as a module ( = code which can be inserted in and removed from the running kernel whenever you want). The module will be called st.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config CHR_DEV_OSST tristate "SCSI OnStream SC-x0 tape support"
@@ -829,7 +829,7 @@ tapes (QIC-157) and can be driven by the standard driver st. For more information, you may have a look at the SCSI-HOWTO <http://www.linuxdoc.org/docs.html#howto> and - <file:drivers/scsi/README.osst> in the kernel source. + <file:Documentation/scsi/osst.txt> in the kernel source. More info on the OnStream driver may be found on <http://linux1.onstream.nl/test/> Please also have a look at the standard st docu, as most of it
@@ -839,7 +839,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called osst.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config BLK_DEV_SR tristate "SCSI CDROM support"
@@ -854,7 +854,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called sr_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. + <file:Documentation/scsi/scsi.txt>. config BLK_DEV_SR_VENDOR bool "Enable vendor-specific extensions (for SCSI CDROM)"
@@ -900,13 +900,13 @@ quality digital reader of audio CDs (<http://www.xiph.org/paranoia/>). For other devices, it's possible that you'll have to write the driver software yourself. Please read the file - <file:Documentation/scsi-generic.txt> for more information. + <file:Documentation/scsi/scsi-generic.txt> for more information. If you want to compile this as a module ( = code which can be inserted in and removed from the running kernel whenever you want), say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. The module will be called sg.o. If unsure, - say N. + <file:Documentation/scsi/scsi.txt>. The module will be called sg.o. + If unsure, say N. comment "Some SCSI devices (e.g. CD jukebox) support multiple LUNs" depends on SCSI
@@ -1025,7 +1025,7 @@ Information on the configuration options for this controller can be found by checking the help file for each of the available configuration options. You should read - <file:drivers/scsi/aic7xxx_old/README.aic7xxx> at a minimum before + <file:Documentation/scsi/aic7xxx_old.txt> at a minimum before contacting the maintainer with any questions. The SCSI-HOWTO, available from <http://www.linuxdoc.org/docs.html#howto>, can also be of great help.
@@ -1051,7 +1051,7 @@ If you say Y here, you can still turn off TCQ on troublesome devices with the use of the tag_info boot parameter. See the file - <file:drivers/scsi/README.aic7xxx> for more information on that and + <file:Documentation/scsi/aic7xxx.txt> for more information on that and other aic7xxx setup commands. If this option is turned off, you may still enable TCQ on known good devices by use of the tag_info boot parameter.
@@ -1061,7 +1061,7 @@ However, TCQ can increase performance on some hard drives by as much as 50% or more, so it is recommended that if you say N here, you - should at least read the <file:drivers/scsi/README.aic7xxx> file so + should at least read the <file:Documentation/scsi/aic7xxx.txt> file so you will know how to enable this option manually should your drives prove to be safe in regards to TCQ.
@@ -1200,7 +1200,7 @@ only one may be active at a time. If you have a 53c8xx board, you probably do not want to use the "NCR53c7,8xx SCSI support". - Please read <file:drivers/scsi/README.ncr53c8xx> for more + Please read <file:Documentation/scsi/ncr53c8xx.txt> for more information. config SCSI_SYM53C8XX
@@ -1227,7 +1227,7 @@ SYM53C8XX driver, thus allowing the NCR53C8XX driver to attach them. The 'excl' option is also supported by the NCR53C8XX driver. - Please read <file:drivers/scsi/README.ncr53c8xx> for more + Please read <file:Documentation/scsi/ncr53c8xx.txt> for more information. config SCSI_NCR53C8XX_DEFAULT_TAGS
@@ -1371,7 +1371,7 @@ If you say Y here, make sure to choose "BIOS" at the question "PCI access mode". - Please read the file <file:drivers/scsi/README.qlogicisp>. You + Please read the file <file:Documentation/scsi/qlogicisp.txt>. You should also read the SCSI-HOWTO, available from <http://www.linuxdoc.org/docs.html#howto>.
arch/x86_64/Kconfig +1 -1
@@ -505,7 +505,7 @@ inserted in and removed from the running kernel whenever you want). The module will be called scsi_mod.o. If you want to compile it as a module, say M here and read <file:Documentation/modules.txt> and - <file:Documentation/scsi.txt>. However, do not compile this as a + <file:Documentation/scsi/scsi.txt>. However, do not compile this as a module if your root file system (the one containing the directory /) is located on a SCSI device.
drivers/scsi/Kconfig +27 -27
202 lines not on this page · raw message
drivers/scsi/aha152x.c +2 -2
@@ -216,7 +216,7 @@* ************************************************************************** - see README.aha152x for configuration details +see Documentation/scsi/aha152x.txt for configuration details **************************************************************************/
@@ -1859,7 +1859,7 @@"aha152x: unable to verify geometry for disk with >1GB.\n" " Using default translation. Please verify yourself.\n" " Perhaps you need to enable extended translation in the driver.\n" - " See /usr/src/linux/drivers/scsi/README.aha152x for details.\n"); + " See /usr/src/linux/Documentation/scsi/aha152x.txt for details.\n"); } }else { info_array[0 ] = info[0 ];
drivers/scsi/aic7xxx/aic7xxx_linux.c +1 -1
@@ -1074,7 +1074,7 @@aic7xxx_setup (aic7xxx);if (dummy_buffer[0 ] !='P' )printk (KERN_WARNING -"aic7xxx: Please read the file /usr/src/linux/drivers/scsi/README.aic7xxx\n" +"aic7xxx: Please read the file /usr/src/linux/Documentation/scsi/aic7xxx.txt\n" "aic7xxx: to see the proper way to specify options to the aic7xxx module\n" "aic7xxx: Specifically, don't use any commas when passing arguments to\n" "aic7xxx: insmod or else it might trash certain memory areas.\n" );
drivers/scsi/dpt/dpti_ioctl.h +2 -1
@@ -5,7 +5,8 @@copyright : (C) 2001 by Adaptec email : [email protected] -See README.dpti for history, notes, license info, and credits +See Documentation/scsi/dpti.txt for history, notes, license info +and credits ***************************************************************************/ /***************************************************************************
drivers/scsi/dpt_i2o.c +3 -2
@@ -5,10 +5,11 @@copyright : (C) 2000 by Adaptec email : [email protected] -July 30, 2001 First version being submitted +July 30, 2001 First version being submitted for inclusion in the kernel. V2.4 -See README.dpti for history, notes, license info, and credits +See Documentation/scsi/dpti.txt for history, notes, license info +and credits ***************************************************************************/ /***************************************************************************
drivers/scsi/dpti.h +2 -1
@@ -5,7 +5,8 @@copyright : (C) 2001 by Adaptec email : [email protected] -See README.dpti for history, notes, license info, and credits +See Documentation/scsi/dpti.txt for history, notes, license info +and credits ***************************************************************************/ /***************************************************************************
drivers/scsi/ibmmca.c +3 -2
@@ -4,8 +4,9 @@ Copyright (c) 1995 Strom Systems, Inc. under the terms of the GNU General Public License. Written by Martin Kolinek, December 1995. Further development by: Chris Beauregard, Klaus Kudielka, Michael Lang - See the file README.ibmmca for a detailed description of this driver, - the commandline arguments and the history of its development. + See the file Documentation/scsi/ibmmca.txt for a detailed description + of this driver, the commandline arguments and the history of its + development. See the WWW-page: http://www.uni-mainz.de/~langm000/linux.html for latest updates, info and ADF-files for adapters supported by this driver.
drivers/scsi/ibmmca.h +3 -2
@@ -1,6 +1,7 @@ -/* +/* * Low Level Driver for the IBM Microchannel SCSI Subsystem -* (Headerfile, see README.ibmmca for description of the IBM MCA SCSI-driver +* (Headerfile, see Documentation/scsi/ibmmca.txt for description of the +* IBM MCA SCSI-driver. * For use under the GNU General Public License within the Linux-kernel project. * This include file works only correctly with kernel 2.4.0 or higher!!! */
drivers/scsi/ncr53c8xx.c +1 -1
@@ -1621,7 +1621,7 @@** Possible data corruption during Memory Write and Invalidate. ** This work-around resets the addressing logic prior to the ** start of the first MOVE of a DATA IN phase. -** (See README.ncr53c8xx for more information) +** (See Documentation/scsi/ncr53c8xx.txt for more information) */ SCR_JUMPR ^IFFALSE (IF (SCR_DATA_IN )), 20,
drivers/scsi/osst.c +1 -1
@@ -1,6 +1,6 @@/* SCSI Tape Driver for Linux version 1.1 and newer. See the accompanying -file README.st for more information. +file Documentation/scsi/st.txt for more information. History:
drivers/scsi/pcmcia/Kconfig +1 -1
@@ -46,7 +46,7 @@ help If you intend to attach this type of PCMCIA SCSI host adapter to your computer, say Y here and read - <file:Documentation/README.nsp_cs.eng>. + <file:Documentation/scsi/NinjaSCSI.txt>. This driver is also available as a module called nsp_cs.o ( = code which can be inserted in and removed from the running kernel
drivers/scsi/qla1280.c +2 -2
@@ -955,8 +955,8 @@qla1280_setup (options,NULL );printk (KERN_WARNING -"qla1280: Please read the file /usr/src/linux/drivers" -"/scsi/README.qla1280\n" +"qla1280: Please read the file /usr/src/linux/Documentation" +"/scsi/qla1280.txt\n" "qla1280: to see the proper way to specify options to the qla1280 " "module\n" "qla1280: Specifically, don't use any commas when passing "
drivers/scsi/st.c +2 -2
@@ -1,6 +1,6 @@/* SCSI Tape Driver for Linux version 1.1 and newer. See the accompanying -file README.st for more information. +file Documentation/scsi/st.txt for more information. History: Rewritten from Dwayne Forsyth's SCSI tape driver by Kai Makisara.
@@ -3576,7 +3576,7 @@ }#ifndef MODULE -/* Set the boot options. Syntax is defined in README.st. +/* Set the boot options. Syntax is defined in Documenation/scsi/st.txt. */ static int __init st_setup (char *str) {
drivers/scsi/tmscsim.c +15 -14
@@ -1,17 +1,18 @@ -/*********************************************************************** -* FILE NAME : TMSCSIM.C * -* BY : C.L. Huang, [email protected] * -* Description: Device Driver for Tekram DC-390(T) PCI SCSI * -* Bus Master Host Adapter * -* (C)Copyright 1995-1996 Tekram Technology Co., Ltd. * -***********************************************************************/ -/* (C) Copyright: put under GNU GPL in 10/96 (see README.tmscsim) * -*************************************************************************/ -/* $Id: tmscsim.c,v 2.60.2.30 2000/12/20 01:07:12 garloff Exp $ */ -/* Enhancements and bugfixes by * +/************************************************************************ +* FILE NAME : TMSCSIM.C * +* BY : C.L. Huang, [email protected] * +* Description: Device Driver for Tekram DC-390(T) PCI SCSI * +* Bus Master Host Adapter * +* (C)Copyright 1995-1996 Tekram Technology Co., Ltd. * +************************************************************************ +* (C) Copyright: put under GNU GPL in 10/96 * +* (see Documentation/scsi/tmscsim.txt) * +************************************************************************ +* $Id: tmscsim.c,v 2.60.2.30 2000/12/20 01:07:12 garloff Exp $ * +* Enhancements and bugfixes by * * Kurt Garloff <[email protected]> <[email protected]> * -***********************************************************************/ -/* HISTORY: * +************************************************************************ +* HISTORY: * * * * REV# DATE NAME DESCRIPTION * * 1.00 96/04/24 CLH First release *
@@ -1521,7 +1522,7 @@DC390_write32 (DMA_ScsiBusCtrl,EN_INT_ON_PCI_ABORT );PDEVSET1 ;PCI_READ_CONFIG_WORD (PDEV ,PCI_STATUS , &pstat);printk ("DC390: Register dump: PCI Status: %04x\n" , pstat); -printk ("DC390: In case of driver trouble read linux/drivers/scsi/README.tmscsim\n" ); +printk ("DC390: In case of driver trouble read linux/Documentation/scsi/tmscsim.txt\n" ); };
include/scsi/sg.h +1 -1
@@ -69,7 +69,7 @@ http://www.torque.net/sg/p/scsi-generic_long.txt A version of this document (potentially out of date) may also be found in the kernel source tree, probably at: - /usr/src/linux/Documentation/scsi-generic.txt . + /usr/src/linux/Documentation/scsi/scsi-generic.txt . Utility and test programs are available at the sg web site. They are bundled as sg_utils (for the lk 2.2 series) and sg3_utils (for the
Quoted 2 lines · [email protected] said:
I asked someone from Adaptec some time ago and he said this one is obsolete. Can you explain me the idea behind this?
I diffed the two and found more than just additions. However, on closer inspection they all look to be simple formatting changes. I've thrown away the serverraid file again.
James