ALI 1533 / hang on boot / vaio c1mhp / 2.4.19 + acpi backport
Hi,
i am seeing a hang on boot on a Crusoe based Vaio C1MHP when enabling the ALI IDE Driver:
These are the last lines:
Unform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33Mhz system bus speed for PIO modes: override with idebus=xx
ALI15X3: IDE controller on PCI bus 00 dev 80
pci_irq-0293 [05] acpi_pci_irq_derive : Unable to derive IRQ for device 00:10.0
PCI: No IRQ known for interrupt pin A of device 00:10.0 - using IRQ 255
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
Kernel 2.4.19 + acpi backport + swsusp
Flo
Signature · 2 lines
Florian Lohoff [email protected] +49-5201-669912 Heisenberg may have been here.
Quoted 7 lines · Florian Lohoff
Hi,
i am seeing a hang on boot on a Crusoe based Vaio C1MHP when enabling the ALI IDE Driver:These are the last lines:
Quoted 7 lines
Unform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33Mhz system bus speed for PIO modes: override with idebus=xx
ALI15X3: IDE controller on PCI bus 00 dev 80
pci_irq-0293 [05]acpi_pci_irq_derive: Unable to derive IRQ for device 00:10.0
PCI: No IRQ known for interrupt pin A of device 00:10.0 - using IRQ 255
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
Try it without the ACPI first. Let me know if that also hangs
Quoted 16 lines · Alan Cox
Quoted 7 lines · Florian Lohoff
Hi,
i am seeing a hang on boot on a Crusoe based Vaio C1MHP when enabling the ALI IDE Driver:These are the last lines:
Quoted 7 lines
Unform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33Mhz system bus speed for PIO modes: override with idebus=xx
ALI15X3: IDE controller on PCI bus 00 dev 80
pci_irq-0293 [05]acpi_pci_irq_derive: Unable to derive IRQ for device 00:10.0
PCI: No IRQ known for interrupt pin A of device 00:10.0 - using IRQ 255
ALI15X3: chipset revision 196
ALI15X3: not 100% native mode: will probe irqs later
Quoted 1 line
Try it without the ACPI first. Let me know if that also hangs
It does - With acpi=off and acpi=off pci=biosirq (as mentioned in that crash). I also tried the somewhere mentioned UDMA66 force (ide0=ata66 ide1=ata66) which does get over this point but fails to mount the root filesystem with IDE errors.
Flo
Signature · 2 lines
Florian Lohoff [email protected] +49-5201-669912 Heisenberg may have been here.
Quoted 4 lines · Florian Lohoff
It does - With acpi=off and acpi=off pci=biosirq (as mentioned in that crash). I also tried the somewhere mentioned UDMA66 force (ide0=ata66 ide1=ata66) which does get over this point but fails to mount the root filesystem with IDE errors.
That woukd make sense. The ALI driver in 2.4.19 supports only ALi north/south properly, not Ali/Transmeta or Ali/ATI combinations. 2.4.20-ac should get Ali/Transmeta right and 2.5.47-ac now has test code to avoid non legacy DMA on the ATI