Skip to contentSkip to conversation

Adding support for ST Audio Media 7.1 to hoontech.[ch]

PATCH In review Henry Walpool 2 participants 2 messages Dec 8, 2002 – Dec 9, 2002

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Adding support for ST Audio Media 7.1 to hoontech.[ch]

_____________________________________________________________
Want a new web-based email account ? ---> http://www.firstlinux.net

_____________________________________________________________
Select your own custom email address for FREE! Get [email protected] w/No Ads, 6MB, POP & more! http://www.everyone.net/selectmail?campaign=tag

Below is a patch to fully enable the Hoontech ST Audio DSP24 Media 7.1. It appears that this card is supported. It was nice to see all the output controls in envy24control.

*** Start Patch ***

alsa-kernel/pci/ice1712/hoontech.c +5 -0
@@ -218,6 +218,11 @@
 		"Hoontech SoundTrack Audio DSP24",
 		snd_ice1712_hoontech_init,
 	},
+	{
+		ICE1712_SUBDEVICE_STDSP24_MEDIA7_1,
+		"Hoontech STA DSP24 Media 7.1",
+		snd_ice1712_hoontech_init,
+	},
 	{ } /* terminator */
 };
 
alsa-kernel/pci/ice1712/hoontech.h +1 -0
@@ -27,6 +27,7 @@
 #define  HOONTECH_DEVICE_DESC 	       "{Hoontech SoundTrack DSP 24},"
 
 #define ICE1712_SUBDEVICE_STDSP24	0x12141217	/* Hoontech SoundTrack Audio DSP 24 */
+#define ICE1712_SUBDEVICE_STDSP24_MEDIA7_1	0x16141217	/* Hoontech ST Audio DSP24 Media 7.1 */
 
 extern struct snd_ice1712_card_info snd_ice1712_hoontech_cards[];
 

*** End Patch ***

Some quick questions.

1) After reading old posts in the mailing lists it appears that the hoontech ice1712 cards don't have the option to change the input gain (analog volume) on analog input. I see no analog volume controls with amixer, or envy24control. Is this true? What ice1712 cards have analog input volume/gain control?

2) Does anyone know the correct way to set the spdif for consumer/professional mode on this card?

3) Claus at st audio support said that this card would not work if gpio_write calls in hoontech.c were made to initilize the box. However, I see no difference using these calls or not using these calls. Does anyone know for sure? Claus said that someone on the mailing list would know the answer.

4) How does one turn off the extra output channels when using oss supported applications, or use only certain output channels when using oss supported applications?

5) How does one access/use the ac97 part of this card?

6) Comments on the card/external box. The RIAA phono pre-amp sucks big time. Does not even compare with a cheap phono pre-amp. Can't record at 96000Hz without overruns using low latency patch and every service I could disable. Card has it's own IRQ also. May have something to do with the via KT133 based motherboard I have.

Thanks

Henry

#1 lore raw

Hi Henry,

At Sun, 8 Dec 2002 15:54:53 -0800 (PST),

Quoted 4 lines · Henry Walpool

Below is a patch to fully enable the Hoontech ST Audio DSP24 Media 7.1. It appears that this card is supported. It was nice to see all the output controls in envy24control.

thanks! applied now to cvs.

Quoted 7 lines

Some quick questions.

1) After reading old posts in the mailing lists it appears that the hoontech ice1712 cards don't have the option to change the input gain (analog volume) on analog input. I see no analog volume controls with amixer, or envy24control. Is this true? What ice1712 cards have analog input volume/gain control?

actually there are no ALSA controls defined for hoontech's DAC/ADC. the (most of) cards from m-audio and terratec have analog controls. it depends on the card design, of course, though.

Quoted 2 lines

2) Does anyone know the correct way to set the spdif for consumer/professional mode on this card?

sorry, no idea about this box.

Quoted 5 lines

3) Claus at st audio support said that this card would not work if gpio_write calls in hoontech.c were made to initilize the box. However, I see no difference using these calls or not using these calls. Does anyone know for sure? Claus said that someone on the mailing list would know the answer.

hmm, i also don't see the reason why not work. hoontech's gpio_write is it's independent from other cards' routines...

Quoted 3 lines

4) How does one turn off the extra output channels when using oss supported applications, or use only certain output channels when using oss supported applications?

it's impossible on the kernel emulation route.
you may try the alsa-oss emulation library.

Quoted 1 line

5) How does one access/use the ac97 part of this card?

in theory, it should be accessible normally as mixer controls (i.e. via alsamixer).
but the ac97 controls look not working well atm.

ciao,

Takashi

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf