Skip to contentSkip to conversation

IGMP problem with 2.5 kernels

DISCUSSION Niels den Otter 2 participants 4 messages Feb 10, 2003 – Mar 4, 2003 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

Hi all,

I have tried to run several IP Multicast applications (SDR, Vat,...) with on 2.5 kernels (now running 2.5.59bk3) without succes. Same applications appear to work on 2.4 kernels.

What seems to be happening is that the application binds to the lo interface instead of eth0 so that no IGMP queries are send out on the ethernet interface. I have a small application that tries to listen to address 233.4.5.9 and here is /proc/net/igmp with and without the app running:

Withtout app running:

 Idx     Device    : Count Querier       Group    Users Timer    Reporter
 1       lo        :     0      V2
                                 010000E0     1 0:FFF779D7               0
 2       eth0      :     3      V2
                                 010000E0     1 0:400DA3C3               0

With app running:

 Idx     Device    : Count Querier       Group    Users Timer    Reporter
 1       lo        :     0      V2
                                 090504E9     1 1:00000C28               1 
                                 010000E0     1 0:FFF73910               0
 2       eth0      :     3      V2
                                 010000E0     1 0:400D62FC               0

Is there a known problem? Or should multicast applications be changed to run on 2.5 kernels?

Thanks,

Niels

#2 lore raw
In reply to a message not in the archive
Quoted 11 lines · Niels den Otter
Quoted 9 lines · Niels den Otter

I have tried to run several IP Multicast applications (SDR, Vat,...) with on 2.5 kernels (now running 2.5.59bk3) without succes. Same applications appear to work on 2.4 kernels.

What seems to be happening is that the application binds to the lo interface instead of eth0 so that no IGMP queries are send out on the ethernet interface. I have a small application that tries to listen to address 233.4.5.9 and here is /proc/net/igmp with and without the app running:

Quoted 3 lines

Did more debugging and disabled my loopback interface to ensure the mcast apps don't bind to this interface. strace shows all applications go wrong with the same error. Is this kernel related?

In the meantime I have had verious discussion on this subject with Antonio Querubin and others and I don't know any solution yet.

Is anyone able to use multicast applications on recent 2.5 kernels and make it send out IGMP joins on an ethernet device?

RFC 1112 says
If the upper-layer protocol chooses not to identify an outgoing interface, a default interface should be used, preferably under the control of system management.

In Linux 2.4 kernels this seems to work with adding a route for 224.0.0.0/4 on the desired ethernet interface. This doesn't work in 2.5 kernels however.

Anyone who knows what the problem is and how it can be solved?

Thanks,

Niels

#3 lore raw
Quoted 32 lines · Niels den Otter
Quoted 11 lines · Niels den Otter
Quoted 9 lines · Niels den Otter

I have tried to run several IP Multicast applications (SDR, Vat,...) with on 2.5 kernels (now running 2.5.59bk3) without succes. Same applications appear to work on 2.4 kernels.

What seems to be happening is that the application binds to the lo interface instead of eth0 so that no IGMP queries are send out on the ethernet interface. I have a small application that tries to listen to address 233.4.5.9 and here is /proc/net/igmp with and without the app running:

Quoted 3 lines

Did more debugging and disabled my loopback interface to ensure the mcast apps don't bind to this interface. strace shows all applications go wrong with the same error. Is this kernel related?

In the meantime I have had verious discussion on this subject with Antonio Querubin and others and I don't know any solution yet.

Is anyone able to use multicast applications on recent 2.5 kernels and make it send out IGMP joins on an ethernet device?

RFC 1112 says
If the upper-layer protocol chooses not to identify an outgoing interface, a default interface should be used, preferably under the control of system management.

In Linux 2.4 kernels this seems to work with adding a route for 224.0.0.0/4 on the desired ethernet interface. This doesn't work in 2.5 kernels however.

Quoted 4 lines

Anyone who knows what the problem is and how it can be solved?

Thanks,

Did you try to use bind() to bind your socket to a specific interface? Using route to obtain side-effects is not the correct way. The application needs to bind the socket to a specific interface if the applications requires a specific interface (which you seem to require). Otherwise, the first interface found will be used as the default. If you can't rebuild the programs, you might work- around the problem by modifying start-up so that your ethernet interfaces are started before loop-back.

You can expriment without rebooting...

Remove all routing entries first.
route del -default xxx
route del -net xxx, etc.

ifconfig eth0 down
ifconfig lo down

Completely reconfigure eth0 first....
Then configure lo.

If you don't remove all the routing entries first, you don't really end up with a new configuration. Something 'remembers' and the order of entries doesn't get changed.

Cheers,
Dick Johnson
Penguin : Linux version 2.4.18 on an i686 machine (797.90 BogoMips). Why is the government concerned about the lunatic fringe? Think about it.

#4 lore raw

Richard,

Quoted 18 lines · Richard B. Johnson

Did you try to use bind() to bind your socket to a specific interface? Using route to obtain side-effects is not the correct way. The application needs to bind the socket to a specific interface if the applications requires a specific interface (which you seem to require). Otherwise, the first interface found will be used as the default. If you can't rebuild the programs, you might work- around the problem by modifying start-up so that your ethernet interfaces are started before loop-back.

You can expriment without rebooting...

Remove all routing entries first.
route del -default xxx
route del -net xxx, etc.

ifconfig eth0 down
ifconfig lo down

Quoted 6 lines

Completely reconfigure eth0 first....
Then configure lo.

If you don't remove all the routing entries first, you don't really end up with a new configuration. Something 'remembers' and the order of entries doesn't get changed.

I have tried both your method and also booting Linux without any interfaces enabled, then enable eth0 and after that also lo.

When only eth0 was enabled, I got the following error from sdr:
pangsit:~> sdr
setsockopt - IP_ADD_MEMBERSHIP: No such device setsockopt - IP_ADD_MEMBERSHIP: No such device
sd_listen: setsockopt IP_ADD_MEMBRSHIP err, addr: 224.2.127.254

I can send strace if this helps.

This is the same problem I see with other multicast applications. It really doesn't want to bind to the ethernet interface.
pangsit:~> ifconfig eth0
eth0 Link encap:Ethernet HWaddr 00:08:74:22:48:CF

            inet addr:192.87.109.130  Bcast:192.87.109.255 Mask:255.255.255.0
            inet6 addr: 2001:610:508:109:208:74ff:fe22:48cf/64 Scope:Global
            inet6 addr: fe80::208:74ff:fe22:48cf/64 Scope:Link
            UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
            RX packets:32863 errors:0 dropped:0 overruns:1 frame:0
            TX packets:150 errors:0 dropped:0 overruns:0 carrier:1
            collisions:0 txqueuelen:100 
            RX bytes:16213097 (15.4 MiB)  TX bytes:16428 (16.0 KiB)
            Interrupt:11 Base address:0xec80 

After bringing up the loopback interface again the applications binds to this interface.

-- Niels