: 2/3: Make SCSI low-level drivers also a seperate, complete selectable submenu
Subsystems (2)
PATCH 1/1 : 2/3: Make SCSI low-level drivers also a seperate, complete selectable submenu
so you can disable all SCSI lowlevel drivers at once.
drivers/scsi/Kconfig +94 -86
@@ -173,27 +173,34 @@ config SCSI_LOGGING menu "SCSI low-level drivers" depends on SCSI!=n +config SCSI_LOWLEVEL + bool "SCSI low-level drivers" + ---help--- + This enables a list of SCSI low-level drivers. + + If unsure, say N. + config SGIWD93_SCSI tristate "SGI WD93C93 SCSI Driver" - depends on SGI_IP22 && SCSI + depends on SGI_IP22 && SCSI && SCSI_LOWLEVEL help If you have a Western Digital WD93 SCSI controller on an SGI MIPS system, say Y. Otherwise, say N. config SCSI_DECNCR tristate "DEC NCR53C94 Scsi Driver" - depends on DECSTATION && TC && SCSI + depends on DECSTATION && TC && SCSI && SCSI_LOWLEVEL help Say Y here to support the NCR53C94 SCSI controller chips on IOASIC based TURBOchannel DECstations and TURBOchannel PMAZ-A cards. config SCSI_DECSII tristate "DEC SII Scsi Driver" - depends on DECSTATION && SCSI + depends on DECSTATION && SCSI && SCSI_LOWLEVEL config BLK_DEV_3W_XXXX_RAID tristate "3ware Hardware ATA-RAID support" - depends on PCI && SCSI + depends on PCI && SCSI && SCSI_LOWLEVEL help 3ware is the only hardware ATA-Raid product in Linux to date. This card is 2,4, or 8 channel master mode support only.
@@ -206,7 +213,7 @@ config BLK_DEV_3W_XXXX_RAID config SCSI_7000FASST tristate "7000FASST SCSI support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL help This driver supports the Western Digital 7000 SCSI host adapter family. Some information is in the source:
@@ -219,7 +226,7 @@ config SCSI_7000FASST config SCSI_ACARD tristate "ACARD SCSI support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This driver supports the ACARD 870U/W SCSI host adapter.
@@ -230,7 +237,7 @@ config SCSI_ACARD config SCSI_AHA152X tristate "Adaptec AHA152X/2825 support" - depends on ISA && SCSI + depends on ISA && SCSI && SCSI_LOWLEVEL ---help--- This is a driver for the AHA-1510, AHA-1520, AHA-1522, and AHA-2825 SCSI host adapters. It also works for the AVA-1505, but the IRQ etc.
@@ -247,7 +254,7 @@ config SCSI_AHA152X config SCSI_AHA1542 tristate "Adaptec AHA1542 support" - depends on ISA && SCSI + depends on ISA && SCSI && SCSI_LOWLEVEL ---help--- This is support for a SCSI host adapter. It is explained in section 3.4 of the SCSI-HOWTO, available from
@@ -263,7 +270,7 @@ config SCSI_AHA1542 config SCSI_AHA1740 tristate "Adaptec AHA1740 support" - depends on EISA && SCSI + depends on EISA && SCSI && SCSI_LOWLEVEL ---help--- This is support for a SCSI host adapter. It is explained in section 3.5 of the SCSI-HOWTO, available from
@@ -278,12 +285,13 @@ config SCSI_AHA1740 config SCSI_AACRAID tristate "Adaptec AACRAID support (EXPERIMENTAL)" - depends on EXPERIMENTAL && SCSI && PCI + depends on EXPERIMENTAL && PCI && SCSI && SCSI_LOWLEVEL source "drivers/scsi/aic7xxx/Kconfig.aic7xxx" config SCSI_AIC7XXX_OLD tristate "Adaptec AIC7xxx support (old driver)" + depends on SCSI && SCSI_LOWLEVEL help WARNING This driver is an older aic7xxx driver and is no longer under active development. Adaptec, Inc. is writing a new driver to
@@ -328,7 +336,7 @@ source "drivers/scsi/aic7xxx/Kconfig.aic # All the I2O code and drivers do not seem to be 64bit safe. config SCSI_DPT_I2O tristate "Adaptec I2O RAID support " - depends on !X86_64 && SCSI + depends on !X86_64 && SCSI && SCSI_LOWLEVEL help This driver supports all of Adaptec's I2O based RAID controllers as well as the DPT SmartRaid V cards. This is an Adaptec maintained
@@ -342,7 +350,7 @@ config SCSI_DPT_I2O config SCSI_ADVANSYS tristate "AdvanSys SCSI support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This is a driver for all SCSI host adapters manufactured by AdvanSys. It is documented in the kernel source in
@@ -356,7 +364,7 @@ config SCSI_ADVANSYS config SCSI_IN2000 tristate "Always IN2000 SCSI support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This is support for an ISA bus SCSI host adapter. You'll find more information in <file:Documentation/scsi/in2000.txt>. If it doesn't work
@@ -371,7 +379,7 @@ config SCSI_IN2000 # does not use pci dma and seems to be isa/onboard only for old machines config SCSI_AM53C974 tristate "AM53/79C974 PCI SCSI support" - depends on !X86_64 && SCSI && PCI + depends on !X86_64 && PCI && SCSI && SCSI_LOWLEVEL ---help--- This is support for the AM53/79C974 SCSI host adapters. Please read <file:Documentation/scsi/AM53C974.txt> for details. Also, the
@@ -389,7 +397,7 @@ config SCSI_AM53C974 config SCSI_MEGARAID tristate "AMI MegaRAID support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This driver supports the AMI MegaRAID 418, 428, 438, 466, 762, 490 and 467 SCSI host adapters.
@@ -401,7 +409,7 @@ config SCSI_MEGARAID config SCSI_BUSLOGIC tristate "BusLogic SCSI support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This is support for BusLogic MultiMaster and FlashPoint SCSI Host Adapters. Consult the SCSI-HOWTO, available from
@@ -419,7 +427,7 @@ config SCSI_BUSLOGIC config SCSI_OMIT_FLASHPOINT bool "Omit FlashPoint support" - depends on SCSI_BUSLOGIC + depends on SCSI_BUSLOGIC && SCSI_LOWLEVEL help This option allows you to omit the FlashPoint support from the BusLogic SCSI driver. The FlashPoint SCCB Manager code is
@@ -428,14 +436,14 @@ config SCSI_OMIT_FLASHPOINT config SCSI_CPQFCTS tristate "Compaq Fibre Channel 64-bit/66Mhz HBA support" - depends on PCI && SCSI + depends on PCI && SCSI && SCSI_LOWLEVEL help Say Y here to compile in support for the Compaq StorageWorks Fibre Channel 64-bit/66Mhz Host Bus Adapter. config SCSI_DMX3191D tristate "DMX3191D SCSI support" - depends on SCSI && PCI + depends on PCI && SCSI && SCSI_LOWLEVEL help This is support for Domex DMX3191D SCSI Host Adapters.
@@ -446,7 +454,7 @@ config SCSI_DMX3191D config SCSI_DTC3280 tristate "DTC3180/3280 SCSI support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL help This is support for DTC 3180/3280 SCSI Host Adapters. Please read the SCSI-HOWTO, available from
@@ -460,7 +468,7 @@ config SCSI_DTC3280 config SCSI_EATA tristate "EATA ISA/EISA/PCI (DPT and generic EATA/DMA-compliant boards) support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This driver supports all EATA/DMA-compliant SCSI host adapters. DPT ISA and all EISA I/O addresses are probed looking for the "EATA"
@@ -514,7 +522,7 @@ config SCSI_EATA_MAX_TAGS config SCSI_EATA_DMA tristate "EATA-DMA [Obsolete] (DPT, NEC, AT&T, SNI, AST, Olivetti, Alphatronix) support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This is support for the EATA-DMA protocol compliant SCSI Host Adapters like the SmartCache III/IV, SmartRAID controller families
@@ -532,7 +540,7 @@ config SCSI_EATA_DMA config SCSI_EATA_PIO tristate "EATA-PIO (old DPT PM2001, PM2012A) support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This driver supports all EATA-PIO protocol compliant SCSI Host Adapters like the DPT PM2001 and the PM2012A. EATA-DMA compliant
@@ -548,7 +556,7 @@ config SCSI_EATA_PIO config SCSI_FUTURE_DOMAIN tristate "Future Domain 16xx SCSI/AHA-2920A support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This is support for Future Domain's 16-bit SCSI host adapters (TMC-1660/1680, TMC-1650/1670, TMC-3260, TMC-1610M/MER/MEX) and
@@ -569,7 +577,7 @@ config SCSI_FUTURE_DOMAIN config SCSI_FD_MCS tristate "Future Domain MCS-600/700 SCSI support" - depends on MCA && SCSI + depends on MCA && SCSI && SCSI_LOWLEVEL ---help--- This is support for Future Domain MCS 600/700 MCA SCSI adapters. Some PS/2 computers are equipped with IBM Fast SCSI Adapter/A which
@@ -584,7 +592,7 @@ config SCSI_FD_MCS config SCSI_GDTH tristate "Intel/ICP (former GDT SCSI Disk Array) RAID Controller support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- Formerly called GDT SCSI Disk Array Controller Support.
@@ -600,7 +608,7 @@ config SCSI_GDTH config SCSI_GENERIC_NCR5380 tristate "Generic NCR5380/53c400 SCSI PIO support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This is a driver for the old NCR 53c80 series of SCSI controllers on boards using PIO. Most boards such as the Trantor T130 fit this
@@ -621,7 +629,7 @@ config SCSI_GENERIC_NCR5380 config SCSI_GENERIC_NCR5380_MMIO tristate "Generic NCR5380/53c400 SCSI MMIO support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This is a driver for the old NCR 53c80 series of SCSI controllers on boards using memory mapped I/O.
@@ -637,7 +645,7 @@ config SCSI_GENERIC_NCR5380_MMIO config SCSI_GENERIC_NCR53C400 bool "Enable NCR53c400 extensions" - depends on SCSI_GENERIC_NCR5380 + depends on SCSI_GENERIC_NCR5380 && SCSI_LOWLEVEL help This enables certain optimizations for the NCR53c400 SCSI cards. You might as well try it out. Note that this driver will only probe
@@ -648,7 +656,7 @@ config SCSI_GENERIC_NCR53C400 config SCSI_IBMMCA tristate "IBMMCA SCSI support" - depends on MCA && SCSI + depends on MCA && SCSI && SCSI_LOWLEVEL ---help--- This is support for the IBM SCSI adapter found in many of the PS/2 series computers. These machines have an MCA bus, so you need to
@@ -720,7 +728,7 @@ config IBMMCA_SCSI_DEV_RESET config SCSI_IPS tristate "IBM ServeRAID support" - depends on X86 && SCSI && PCI + depends on X86 && PCI && SCSI && SCSI_LOWLEVEL ---help--- This is support for the IBM ServeRAID hardware RAID controllers. See <http://www.developer.ibm.com/welcome/netfinity/serveraid.html>
@@ -736,7 +744,7 @@ config SCSI_IPS config SCSI_INITIO tristate "Initio 9100U(W) support" - depends on SCSI && PCI + depends on PCI && SCSI && SCSI_LOWLEVEL help This is support for the Initio 91XXU(W) SCSI host adapter. Please read the SCSI-HOWTO, available from
@@ -749,7 +757,7 @@ config SCSI_INITIO config SCSI_INIA100 tristate "Initio INI-A100U2W support" - depends on SCSI && PCI + depends on PCI && SCSI && SCSI_LOWLEVEL help This is support for the Initio INI-A100U2W SCSI host adapter. Please read the SCSI-HOWTO, available from
@@ -762,7 +770,7 @@ config SCSI_INIA100 config SCSI_PPA tristate "IOMEGA parallel port (ppa - older drives)" - depends on SCSI && PARPORT + depends on SCSI && PARPORT && SCSI_LOWLEVEL ---help--- This driver supports older versions of IOMEGA's parallel port ZIP drive (a 100 MB removable media device).
@@ -791,7 +799,7 @@ config SCSI_PPA config SCSI_IMM tristate "IOMEGA parallel port (imm - newer drives)" - depends on SCSI && PARPORT + depends on SCSI && PARPORT && SCSI_LOWLEVEL ---help--- This driver supports newer versions of IOMEGA's parallel port ZIP drive (a 100 MB removable media device).
@@ -820,7 +828,7 @@ config SCSI_IMM config SCSI_IZIP_EPP16 bool "ppa/imm option - Use slow (but safe) EPP-16" - depends on PARPORT && (SCSI_PPA || SCSI_IMM) + depends on PARPORT && (SCSI_PPA || SCSI_IMM) && SCSI_LOWLEVEL ---help--- EPP (Enhanced Parallel Port) is a standard for parallel ports which allows them to act as expansion buses that can handle up to 64
@@ -835,7 +843,7 @@ config SCSI_IZIP_EPP16 config SCSI_IZIP_SLOW_CTR bool "ppa/imm option - Assume slow parport control register" - depends on PARPORT && (SCSI_PPA || SCSI_IMM) + depends on PARPORT && (SCSI_PPA || SCSI_IMM) && SCSI_LOWLEVEL help Some parallel ports are known to have excessive delays between changing the parallel port control register and good data being
@@ -849,7 +857,7 @@ config SCSI_IZIP_SLOW_CTR config SCSI_NCR53C406A tristate "NCR53c406a SCSI support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL help This is support for the NCR53c406a SCSI host adapter. For user configurable parameters, check out <file:drivers/scsi/NCR53c406a.c>
@@ -863,7 +871,7 @@ config SCSI_NCR53C406A config SCSI_NCR_D700 tristate "NCR Dual 700 MCA SCSI support" - depends on MCA && SCSI + depends on MCA && SCSI && SCSI_LOWLEVEL help This is a driver for the MicroChannel Dual 700 card produced by NCR and commonly used in 345x/35xx/4100 class machines. It always
@@ -879,7 +887,7 @@ config 53C700_IO_MAPPED config SCSI_LASI700 tristate "HP LASI SCSI support for 53c700/710" - depends on PARISC && SCSI + depends on PARISC && SCSI && SCSI_LOWLEVEL help This is a driver for the lasi baseboard in some parisc machines which is based on the 53c700 chip. Will also support LASI subsystems
@@ -899,7 +907,7 @@ config 53C700_LE_ON_BE config SCSI_NCR53C7xx tristate "NCR53c7,8xx SCSI support" - depends on SCSI && PCI + depends on PCI && SCSI && SCSI_LOWLEVEL ---help--- This is a driver for the 53c7 and 8xx NCR family of SCSI controllers, not to be confused with the NCR 5380 controllers. It
@@ -953,7 +961,7 @@ config SCSI_NCR53C7xx_DISCONNECT config SCSI_SYM53C8XX_2 tristate "SYM53C8XX Version 2 SCSI support" - depends on PCI && SCSI + depends on PCI && SCSI && SCSI_LOWLEVEL ---help--- This driver supports the whole NCR53C8XX/SYM53C8XX family of PCI-SCSI controllers. It also supports the subset of LSI53C10XX
@@ -969,7 +977,7 @@ config SCSI_SYM53C8XX_2 config SCSI_ZALON tristate "Zalon SCSI support" - depends on GSC && SCSI + depends on GSC && SCSI && SCSI_LOWLEVEL help The Zalon is a GSC/HSC bus interface chip that sits between the PA-RISC processor and the NCR 53c720 SCSI controller on C100,
@@ -979,7 +987,7 @@ config SCSI_ZALON config SCSI_SYM53C8XX_DMA_ADDRESSING_MODE int "DMA addressing mode" - depends on SCSI_SYM53C8XX_2 + depends on SCSI_SYM53C8XX_2 && SCSI_LOWLEVEL default "1" ---help--- This option only applies to PCI-SCSI chip that are PCI DAC capable
@@ -1006,7 +1014,7 @@ config SCSI_SYM53C8XX_DMA_ADDRESSING_MOD config SCSI_SYM53C8XX_DEFAULT_TAGS int "default tagged command queue depth" - depends on SCSI_SYM53C8XX_2 + depends on SCSI_SYM53C8XX_2 && SCSI_LOWLEVEL default "16" help This is the default value of the command queue depth the driver will
@@ -1016,7 +1024,7 @@ config SCSI_SYM53C8XX_DEFAULT_TAGS config SCSI_SYM53C8XX_MAX_TAGS int "maximum number of queued commands" - depends on SCSI_SYM53C8XX_2 + depends on SCSI_SYM53C8XX_2 && SCSI_LOWLEVEL default "64" help This option allows you to specify the maximum number of commands
@@ -1026,14 +1034,14 @@ config SCSI_SYM53C8XX_MAX_TAGS config SCSI_SYM53C8XX_IOMAPPED bool "use normal IO" - depends on SCSI_SYM53C8XX_2 + depends on SCSI_SYM53C8XX_2 && SCSI_LOWLEVEL help If you say Y here, the driver will preferently use normal IO rather than memory mapped IO. config SCSI_NCR53C8XX tristate "NCR53C8XX SCSI support" - depends on PCI && SCSI_SYM53C8XX_2!=y && SCSI + depends on PCI && SCSI_SYM53C8XX_2!=y && SCSI && SCSI_LOWLEVEL ---help--- This is the BSD ncr driver adapted to Linux for the NCR53C8XX family of PCI-SCSI controllers. This driver supports parity checking,
@@ -1054,7 +1062,7 @@ config SCSI_NCR53C8XX config SCSI_SYM53C8XX tristate "SYM53C8XX SCSI support" - depends on PCI && SCSI_SYM53C8XX_2!=y && SCSI + depends on PCI && SCSI_SYM53C8XX_2!=y && SCSI && SCSI_LOWLEVEL ---help--- This driver supports all the features of recent 53C8XX chips (used in PCI SCSI controllers), notably the hardware phase mismatch
@@ -1081,7 +1089,7 @@ config SCSI_SYM53C8XX config SCSI_NCR53C8XX_DEFAULT_TAGS int "default tagged command queue depth" - depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) + depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && SCSI_LOWLEVEL default "8" ---help--- "Tagged command queuing" is a feature of SCSI-2 which improves
@@ -1107,7 +1115,7 @@ config SCSI_NCR53C8XX_DEFAULT_TAGS config SCSI_NCR53C8XX_MAX_TAGS int "maximum number of queued commands" - depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) + depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && SCSI_LOWLEVEL default "32" ---help--- This option allows you to specify the maximum number of commands
@@ -1124,7 +1132,7 @@ config SCSI_NCR53C8XX_MAX_TAGS config SCSI_NCR53C8XX_SYNC int "synchronous transfers frequency in MHz" - depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) + depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && SCSI_LOWLEVEL default "20" ---help--- The SCSI Parallel Interface-2 Standard defines 5 classes of transfer
@@ -1158,7 +1166,7 @@ config SCSI_NCR53C8XX_SYNC config SCSI_NCR53C8XX_PROFILE bool "enable profiling" - depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) + depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && SCSI_LOWLEVEL help This option allows you to enable profiling information gathering. These statistics are not very accurate due to the low frequency
@@ -1169,7 +1177,7 @@ config SCSI_NCR53C8XX_PROFILE config SCSI_NCR53C8XX_IOMAPPED bool "use normal IO" - depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX) && !SCSI_ZALON + depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX) && !SCSI_ZALON && SCSI_LOWLEVEL help If you say Y here, the driver will use normal IO, as opposed to memory mapped IO. Memory mapped IO has less latency than normal IO
@@ -1182,7 +1190,7 @@ config SCSI_NCR53C8XX_IOMAPPED config SCSI_NCR53C8XX_PQS_PDS bool "include support for the NCR PQS/PDS SCSI card" - depends on (SCSI_NCR53C8XX || SCSI_SYM53C8XX) && SCSI_SYM53C8XX + depends on (SCSI_NCR53C8XX || SCSI_SYM53C8XX) && SCSI_SYM53C8XX && SCSI_LOWLEVEL help Say Y here if you have a special SCSI adapter produced by NCR corporation called a PCI Quad SCSI or PCI Dual SCSI. You do not need
@@ -1194,7 +1202,7 @@ config SCSI_NCR53C8XX_PQS_PDS config SCSI_NCR53C8XX_NO_DISCONNECT bool "not allow targets to disconnect" - depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && SCSI_NCR53C8XX_DEFAULT_TAGS=0 + depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && SCSI_NCR53C8XX_DEFAULT_TAGS=0 && SCSI_LOWLEVEL help This option is only provided for safety if you suspect some SCSI device of yours to not support properly the target-disconnect
@@ -1204,7 +1212,7 @@ config SCSI_NCR53C8XX_NO_DISCONNECT config SCSI_NCR53C8XX_SYMBIOS_COMPAT bool "assume boards are SYMBIOS compatible (EXPERIMENTAL)" - depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && EXPERIMENTAL + depends on PCI && SCSI_SYM53C8XX_2!=y && (SCSI_NCR53C8XX || SCSI_SYM53C8XX || SCSI_ZALON) && EXPERIMENTAL && SCSI_LOWLEVEL && SCSI_LOWLEVEL ---help--- This option allows you to enable some features depending on GPIO wiring. These General Purpose Input/Output pins can be used for
@@ -1224,7 +1232,7 @@ config SCSI_NCR53C8XX_SYMBIOS_COMPAT config SCSI_MCA_53C9X tristate "NCR MCA 53C9x SCSI support" - depends on MCA && SCSI + depends on MCA && SCSI && SCSI_LOWLEVEL help Some MicroChannel machines, notably the NCR 35xx line, use a SCSI controller based on the NCR 53C94. This driver will allow use of
@@ -1237,7 +1245,7 @@ config SCSI_MCA_53C9X config SCSI_PAS16 tristate "PAS16 SCSI support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL ---help--- This is support for a SCSI host adapter. It is explained in section 3.10 of the SCSI-HOWTO, available from
@@ -1252,7 +1260,7 @@ config SCSI_PAS16 config SCSI_PCI2000 tristate "PCI2000 support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This is support for the PCI2000I EIDE interface card which acts as a SCSI host adapter. Please read the SCSI-HOWTO, available from
@@ -1265,7 +1273,7 @@ config SCSI_PCI2000 config SCSI_PCI2220I tristate "PCI2220i support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This is support for the PCI2220i EIDE interface card which acts as a SCSI host adapter. Please read the SCSI-HOWTO, available from
@@ -1278,7 +1286,7 @@ config SCSI_PCI2220I config SCSI_PSI240I tristate "PSI240i support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL help This is support for the PSI240i EIDE interface card which acts as a SCSI host adapter. Please read the SCSI-HOWTO, available from
@@ -1291,7 +1299,7 @@ config SCSI_PSI240I config SCSI_QLOGIC_FAS tristate "Qlogic FAS SCSI support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL ---help--- This is a driver for the ISA, VLB, and PCMCIA versions of the Qlogic FastSCSI! cards as well as any other card based on the FASXX chip
@@ -1313,7 +1321,7 @@ config SCSI_QLOGIC_FAS config SCSI_QLOGIC_ISP tristate "Qlogic ISP SCSI support" - depends on PCI && SCSI + depends on PCI && SCSI && SCSI_LOWLEVEL ---help--- This driver works for all QLogic PCI SCSI host adapters (IQ-PCI, IQ-PCI-10, IQ_PCI-D) except for the PCI-basic card. (This latter
@@ -1333,7 +1341,7 @@ config SCSI_QLOGIC_ISP config SCSI_QLOGIC_FC tristate "Qlogic ISP FC SCSI support" - depends on PCI && SCSI + depends on PCI && SCSI && SCSI_LOWLEVEL help This is a driver for the QLogic ISP2100 SCSI-FCP host adapter.
@@ -1352,7 +1360,7 @@ config SCSI_QLOGIC_FC_FIRMWARE config SCSI_QLOGIC_1280 tristate "Qlogic QLA 1280 SCSI support" - depends on PCI && SCSI + depends on PCI && SCSI && SCSI_LOWLEVEL help Say Y if you have a QLogic ISP1x80/1x160 SCSI host adapter.
@@ -1363,7 +1371,7 @@ config SCSI_QLOGIC_1280 config SCSI_SEAGATE tristate "Seagate ST-02 and Future Domain TMC-8xx SCSI support" - depends on X86 && ISA && SCSI + depends on X86 && ISA && SCSI && SCSI_LOWLEVEL ---help--- These are 8-bit SCSI controllers; the ST-01 is also supported by this driver. It is explained in section 3.9 of the SCSI-HOWTO,
@@ -1379,7 +1387,7 @@ config SCSI_SEAGATE # definitely looks note 64bit safe: config SCSI_SIM710 tristate "Simple 53c710 SCSI support (Compaq, NCR machines)" - depends on (EISA || MCA && !X86_64) && SCSI + depends on (EISA || MCA && !X86_64) && SCSI && SCSI_LOWLEVEL ---help--- This driver for NCR53c710 based SCSI host adapters.
@@ -1392,7 +1400,7 @@ config 53C700_IO_MAPPED config SCSI_SYM53C416 tristate "Symbios 53c416 SCSI support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL ---help--- This is support for the sym53c416 SCSI host adapter, the SCSI adapter that comes with some HP scanners. This driver requires that
@@ -1413,7 +1421,7 @@ config SCSI_SYM53C416 config SCSI_DC390T tristate "Tekram DC390(T) and Am53/79C974 SCSI support" - depends on PCI && SCSI + depends on PCI && SCSI && SCSI_LOWLEVEL ---help--- This driver supports PCI SCSI host adapters based on the Am53C974A chip, e.g. Tekram DC390(T), DawiControl 2974 and some onboard
@@ -1450,7 +1458,7 @@ config SCSI_DC390T_NOGENSUPP config SCSI_T128 tristate "Trantor T128/T128F/T228 SCSI support" - depends on SCSI && ISA + depends on ISA && SCSI && SCSI_LOWLEVEL ---help--- This is support for a SCSI host adapter. It is explained in section 3.11 of the SCSI-HOWTO, available from
@@ -1467,7 +1475,7 @@ config SCSI_T128 config SCSI_U14_34F tristate "UltraStor 14F/34F support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL ---help--- This is support for the UltraStor 14F and 34F SCSI-2 host adapters. The source at <file:drivers/scsi/u14-34f.c> contains some
@@ -1518,7 +1526,7 @@ config SCSI_U14_34F_MAX_TAGS config SCSI_ULTRASTOR tristate "UltraStor SCSI support" - depends on X86 && ISA && SCSI + depends on X86 && ISA && SCSI && SCSI_LOWLEVEL ---help--- This is support for the UltraStor 14F, 24F and 34F SCSI-2 host adapter family. This driver is explained in section 3.12 of the
@@ -1537,7 +1545,7 @@ config SCSI_ULTRASTOR config SCSI_NSP32 tristate "Workbit NinjaSCSI-32Bi/UDE support" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This is support for the Workbit NinjaSCSI-32Bi/UDE PCI/Cardbus SCSI host adapter. Please read the SCSI-HOWTO, available from
@@ -1550,7 +1558,7 @@ config SCSI_NSP32 config SCSI_DEBUG tristate "SCSI debugging host simulator" - depends on SCSI + depends on SCSI && SCSI_LOWLEVEL help This is a host adapter simulator that can simulate multiple hosts each with multiple dummy SCSI devices (disks). It defaults to one
@@ -1563,7 +1571,7 @@ config SCSI_DEBUG config SCSI_MESH tristate "MESH (Power Mac internal SCSI) support" - depends on ALL_PPC && SCSI + depends on ALL_PPC && SCSI && SCSI_LOWLEVEL help Many Power Macintoshes and clones have a MESH (Macintosh Enhanced SCSI Hardware) SCSI bus adaptor (the 7200 doesn't, but all of the
@@ -1594,7 +1602,7 @@ config SCSI_MESH_RESET_DELAY_MS config SCSI_MAC53C94 tristate "53C94 (Power Mac external SCSI) support" - depends on ALL_PPC && SCSI + depends on ALL_PPC && SCSI && SCSI_LOWLEVEL help On Power Macintoshes (and clones) with two SCSI buses, the external SCSI bus is usually controlled by a 53C94 SCSI bus adaptor. Older
@@ -1618,7 +1626,7 @@ config JAZZ_ESP config A3000_SCSI tristate "A3000 WD33C93A support" - depends on AMIGA && SCSI + depends on AMIGA && SCSI && SCSI_LOWLEVEL help If you have an Amiga 3000 and have SCSI devices connected to the built-in SCSI controller, say Y. Otherwise, say N. This driver is
@@ -1635,7 +1643,7 @@ config A4000T_SCSI config A2091_SCSI tristate "A2091/A590 WD33C93A support" - depends on ZORRO && SCSI + depends on ZORRO && SCSI && SCSI_LOWLEVEL help If you have a Commodore A2091 SCSI controller, say Y. Otherwise, say N. This driver is also available as a module ( = code which can
@@ -1645,7 +1653,7 @@ config A2091_SCSI config GVP11_SCSI tristate "GVP Series II WD33C93A support" - depends on ZORRO && SCSI + depends on ZORRO && SCSI && SCSI_LOWLEVEL ---help--- If you have a Great Valley Products Series II SCSI controller, answer Y. Also say Y if you have a later model of GVP SCSI
@@ -1660,7 +1668,7 @@ config GVP11_SCSI config CYBERSTORM_SCSI tristate "CyberStorm SCSI support" - depends on ZORRO && SCSI + depends on ZORRO && SCSI && SCSI_LOWLEVEL help If you have an Amiga with an original (MkI) Phase5 Cyberstorm accelerator board and the optional Cyberstorm SCSI controller,
@@ -1668,7 +1676,7 @@ config CYBERSTORM_SCSI config CYBERSTORMII_SCSI tristate "CyberStorm Mk II SCSI support" - depends on ZORRO && SCSI + depends on ZORRO && SCSI && SCSI_LOWLEVEL help If you have an Amiga with a Phase5 Cyberstorm MkII accelerator board and the optional Cyberstorm SCSI controller, say Y. Otherwise,
@@ -1676,7 +1684,7 @@ config CYBERSTORMII_SCSI config BLZ2060_SCSI tristate "Blizzard 2060 SCSI support" - depends on ZORRO && SCSI + depends on ZORRO && SCSI && SCSI_LOWLEVEL help If you have an Amiga with a Phase5 Blizzard 2060 accelerator board and want to use the onboard SCSI controller, say Y. Otherwise,
@@ -1684,7 +1692,7 @@ config BLZ2060_SCSI config BLZ1230_SCSI tristate "Blizzard 1230IV/1260 SCSI support" - depends on ZORRO && SCSI + depends on ZORRO && SCSI && SCSI_LOWLEVEL help If you have an Amiga 1200 with a Phase5 Blizzard 1230IV or Blizzard 1260 accelerator, and the optional SCSI module, say Y. Otherwise,
@@ -1692,7 +1700,7 @@ config BLZ1230_SCSI config FASTLANE_SCSI tristate "Fastlane SCSI support" - depends on ZORRO && SCSI + depends on ZORRO && SCSI && SCSI_LOWLEVEL help If you have the Phase5 Fastlane Z3 SCSI controller, or plan to use one in the near future, say Y to this question. Otherwise, say N.
@@ -1722,7 +1730,7 @@ config BLZ603EPLUS_SCSI config OKTAGON_SCSI tristate "BSC Oktagon SCSI support (EXPERIMENTAL)" - depends on ZORRO && EXPERIMENTAL && SCSI + depends on ZORRO && EXPERIMENTAL && SCSI && SCSI_LOWLEVEL help If you have the BSC Oktagon SCSI disk controller for the Amiga, say Y to this question. If you're in doubt about whether you have one,
drivers/scsi/aic7xxx/Kconfig.aic79xx +1 -1
@@ -4,7 +4,7 @@ # config SCSI_AIC79XX tristate "Adaptec AIC79xx U320 support" - depends on PCI + depends on PCI && SCSI_LOWLEVEL help This driver supports all of Adaptec's Ultra 320 PCI-X based SCSI controllers.
drivers/scsi/aic7xxx/Kconfig.aic7xxx +1 -0
@@ -4,6 +4,7 @@ # config SCSI_AIC7XXX tristate "Adaptec AIC7xxx Fast -> U160 support (New Driver)" + depends on SCSI_LOWLEVEL ---help--- This driver supports all of Adaptec's Fast through Ultra 160 PCI based SCSI controllers as well as the aic7770 based EISA and VLB
Quoted 1 line · Marc-Christian Petersen
so you can disable all SCSI lowlevel drivers at once.
Why? just disable CONFIG_SCSI instead of adding an artifical option
Quoted 4 lines · Christoph Hellwig
Quoted 1 line · Marc-Christian Petersen
so you can disable all SCSI lowlevel drivers at once.
Why? just disable
CONFIG_SCSIinstead of adding an artifical option
Isn't that going to disable all of SCSI? I think the intention may be to drop hardware drivers and just use ide-scsi, although I might be misreading the original intent.
There are a fair number of tape/CD/DVD devices out there which you might run SCSI. I many cases will run SCSI or not at all.
Signature · 3 lines
bill davidsen <[email protected]> CTO, TMR Associates, Inc Doing interesting things with little computers since 1979.
Quoted 5 lines · Bill Davidsen
Quoted 3 lines · Christoph Hellwig
Quoted 1 line · Marc-Christian Petersen
so you can disable all SCSI lowlevel drivers at once.
Quoted 8 lines
Quoted 1 line
Why? just disable
CONFIG_SCSIinstead of adding an artifical optionIsn't that going to disable all of SCSI? I think the intention may be to drop hardware drivers and just use ide-scsi, although I might be misreading the original intent.
There are a fair number of tape/CD/DVD devices out there which you might run SCSI. I many cases will run SCSI or not at all.
I thought the intent was to make it unnecessary to run ide-scsi at all. There was talk about it awhile back on the list. I've been burning CDs using ide cdrom support for several kernel revisions now.
Quoted 9 lines · Thomas Molina
Quoted 7 lines · Bill Davidsen
Quoted 4 lines · Christoph Hellwig
Quoted 1 line · Marc-Christian Petersen
so you can disable all SCSI lowlevel drivers at once.
Why? just disable
CONFIG_SCSIinstead of adding an artifical option
Quoted 8 lines
Quoted 6 lines
Isn't that going to disable all of SCSI? I think the intention may be to drop hardware drivers and just use ide-scsi, although I might be misreading the original intent.
There are a fair number of tape/CD/DVD devices out there which you might run SCSI. I many cases will run SCSI or not at all.
I thought the intent was to make it unnecessary to run ide-scsi at all.
I don't think it matters, the idea is to avoid all the low-level SCSI menus in one place, without disabling the ability to handle ATAPI devices. Using the ide-scsi or not still uses SCSI drivers AFAIK.
Quoted 2 lines
There was talk about it awhile back on the list. I've been burning CDs using ide cdrom support for several kernel revisions now.
Have you checked/used them? I kind of wrote that off after a while, I don't need more coasters :-( At the time I deferred testing the score was
CD: read okay burn failed, ide-floppy (ZIP in my case): ng, and tape: not even visible. That was back around 2.5.52 or so, since ide-scsi seems to work I haven't been motivated to care.
Signature · 3 lines
bill davidsen <[email protected]> CTO, TMR Associates, Inc Doing interesting things with little computers since 1979.
Quoted 4 lines · Bill Davidsen
I don't think it matters, the idea is to avoid all the low-level SCSI menus in one place, without disabling the ability to handle ATAPI devices. Using the ide-scsi or not still uses SCSI drivers AFAIK.
Quoted 8 lines
Quoted 2 lines
There was talk about it awhile back on the list. I've been burning CDs using ide cdrom support for several kernel revisions now.
Have you checked/used them? I kind of wrote that off after a while, I don't need more coasters :-( At the time I deferred testing the score was
CD: read okay burn failed, ide-floppy (ZIP in my case): ng, and tape: not even visible. That was back around 2.5.52 or so, since ide-scsi seems to work I haven't been motivated to care.
As I said, I've been using it successfully. I've not tested ide-floppy since I don't have one, nor a tape. I would rather not have to use ide-scsi if I can help it. ide cd support is incompatible with ide-scsi cdrom support, so things are simpler if I can just cut out the scsi support entirely.
Quoted 8 lines · Thomas Molina
Quoted 5 lines · Bill Davidsen
Have you checked/used them? I kind of wrote that off after a while, I don't need more coasters :-( At the time I deferred testing the score was
CD: read okay burn failed, ide-floppy (ZIP in my case): ng, and tape: not even visible. That was back around 2.5.52 or so, since ide-scsi seems to work I haven't been motivated to care.
Quoted 5 lines
As I said, I've been using it successfully. I've not tested ide-floppy since I don't have one, nor a tape. I would rather not have to use ide-scsi if I can help it. ide cd support is incompatible with ide-scsi cdrom support, so things are simpler if I can just cut out the scsi support entirely.
Since I have SCSI devices I'd rather make the ATAPI devices look SCSI than have two sets of tools to do things. And two sets of drivers loaded, two sources of possible bugs, etc. That just seems simpler to me.
Thanks for the input.
Signature · 3 lines
bill davidsen <[email protected]> CTO, TMR Associates, Inc Doing interesting things with little computers since 1979.
Quoted 15 lines · Bill Davidsen
Quoted 13 lines · Thomas Molina
Quoted 11 lines · Bill Davidsen
Quoted 4 lines · Christoph Hellwig
Quoted 1 line · Marc-Christian Petersen
so you can disable all SCSI lowlevel drivers at once.
Why? just disable
CONFIG_SCSIinstead of adding an artifical optionIsn't that going to disable all of SCSI? I think the intention may be to drop hardware drivers and just use ide-scsi, although I might be misreading the original intent.
Quoted 8 lines
Quoted 4 lines
Quoted 2 lines
There are a fair number of tape/CD/DVD devices out there which you might run SCSI. I many cases will run SCSI or not at all.
I thought the intent was to make it unnecessary to run ide-scsi at all.
I don't think it matters, the idea is to avoid all the low-level SCSI menus in one place, without disabling the ability to handle ATAPI devices. Using the ide-scsi or not still uses SCSI drivers AFAIK.
But as far as linux scsi is concerned, ide-scsi is a low-level SCSI driver.
IDE and USB have there own Kconfig options that enable low-level SCSI driver emulation outside of drivers/scsi, pcmcia does not, and there are probably other exceptions.
The following is simpler, though I'm not suggesting anything like this be applied, since we don't have consitency. If all of the low-level scsi drivers and options were under drivers/scsi, and we could separate emulated versus real, something like this might be OK:
drivers/scsi/Kconfig +9 -1
@@ -170,8 +170,16 @@ logging turned off. +config SCSI_LOW_LEVEL + bool "SCSI low level drivers" + + help + enables a list of additional SCSI low level drivers + + If you need one of the drivers here say Y, else say N ;-) + menu "SCSI low-level drivers" - depends on SCSI!=n + depends on SCSI!=n && SCSI_LOW_LEVEL!=n config SGIWD93_SCSI tristate "SGI WD93C93 SCSI Driver"
-- Patrick Mansfield
Quoted 8 lines · Patrick Mansfield
Quoted 3 lines · Bill Davidsen
I don't think it matters, the idea is to avoid all the low-level SCSI menus in one place, without disabling the ability to handle ATAPI devices. Using the ide-scsi or not still uses SCSI drivers AFAIK.
But as far as linux scsi is concerned, ide-scsi is a low-level SCSI driver.
Quoted 8 lines
IDE and USB have there own
Kconfigoptions that enable low-level SCSI driver emulation outside ofdrivers/scsi, pcmcia does not, and there are probably other exceptions.The following is simpler, though I'm not suggesting anything like this be applied, since we don't have consitency. If all of the low-level scsi drivers and options were under
drivers/scsi, and we could separate emulated versus real, something like this might be OK:
I think this is a very good idea. In the long run this is one of those matrix things, is SCSI on USB an entry in a menu of USB or SCSI? And until we can access the option from either place and still have exactly one option, we (someone) must decide which it is.
Clearly unless we do it both way at some time, some portion of the users will find either choice unintuitive. What you propose is a step forward, and if extensions are made in 2.7 which suggest rethinking, so be it.
Thanks for the patch, it's goin in my tree.
Signature · 3 lines
bill davidsen <[email protected]> CTO, TMR Associates, Inc Doing interesting things with little computers since 1979.