USB harddrive not working (2.4, 2.5)
Hi,
ISD200 based hard drive bay doesn't work with 2.4 & 2.5, can someone assist me with it?
Kernel message log appended.
Best regards.
Signature · 2 lines
Andrey Panin | Embedded systems software developer [email protected] | PGP key: wwwkeys.pgp.net
drivers/usb/core/usb.c: registered new driver hub drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.0
PCI: Found IRQ 11 for device 00:1f.2
PCI: Setting latency timer of device 00:1f.2 to 64
uhci-hcd 00:1f.2: Intel Corp. 82801AA USB
uhci-hcd 00:1f.2: irq 11, io base 0000d000
uhci-hcd 00:1f.2: new USB bus registered, assigned bus number 1
hub 1-0:0: USB hub found
hub 1-0:0: 2 ports detected
hub 1-0:0: debounce: port 2: delay 100ms stable 4 status 0x101
hub 1-0:0: new USB device on port 2, assigned address 2 Initializing USB Mass Storage driver...
usb-storage: act_altsetting is 0 usb-storage: id_index calculated to be: 32 usb-storage: Array length appears to be: 81 usb-storage: Vendor: In-System usb-storage: Product: USB/IDE Bridge (ATA/ATAPI) usb-storage: USB Mass Storage device detected usb-storage: Endpoints: In: 0xc336b934 Out: 0xc336b920 Int: 0xc336b948 (Period 32) usb-storage: GetMaxLUN command result is 1, data is 0 usb-storage: Transport: Bulk usb-storage: Protocol: ISD200 ATA/ATAPI usb-storage: Allocating usb_ctrlrequest usb-storage: Allocating URB usb-storage: Allocating scatter-gather request block usb-storage: ISD200 Initialization... usb-storage: Entering isd200_get_inquiry_data usb-storage: Entering isd200_manual_enum usb-storage: Entering isd200_read_config usb-storage: usb_stor_ctrl_transfer(): rq=02 rqtype=c0 value=0000 index=02 len=8 usb-storage: Status code 0; transferred 8/8 usb-storage: -- transfer complete usb-storage: Retrieved the following ISD200 Config Data: usb-storage: Event Notification: 0x0 usb-storage: External Clock: 0x0 usb-storage: ATA Init Timeout: 0x19 usb-storage: ATAPI Command Block Size: 0x0 usb-storage: Master/Slave Selection: 0x0 usb-storage: ATAPI Reset: 0x0 usb-storage: ATA Timing: 0x1 usb-storage: ATA Major Command: 0x24 usb-storage: ATA Minor Command: 0x24 usb-storage: Init Status: 0x0 usb-storage: Config Descriptor 2: 0x0 usb-storage: Skip Device Boot: 0x0 usb-storage: ATA 3 State Supsend: 0x0 usb-storage: Descriptor Override: 0x8 usb-storage: Last LUN Identifier: 0x0 usb-storage: SRST Enable: 0x0 usb-storage: Leaving isd200_read_config 00000000 usb-storage: isd200_action(ENUM,0xa0) usb-storage: Bulk command S 0x43425355 T 0x0 Trg 0 LUN 1 L 0 F 0 CL 0 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code -32; transferred 0/13 usb-storage: clearing endpoint halt for pipe 0xc0010280 usb-storage: usb_stor_clear_halt: result=0 usb-storage: Attempting to get CSW (2nd try)... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code -32; transferred 0/13 usb-storage: clearing endpoint halt for pipe 0xc0010280 usb-storage: usb_stor_clear_halt: result=0 usb-storage: Bulk status result = 2 usb-storage: isd200_action(0x04) error: 2 usb-storage: Setting Master/Slave selection to 0 usb-storage: Entering isd200_write_config usb-storage: Writing the following ISD200 Config Data: usb-storage: Event Notification: 0x0 usb-storage: External Clock: 0x0 usb-storage: ATA Init Timeout: 0x19 usb-storage: ATAPI Command Block Size: 0x0 usb-storage: Master/Slave Selection: 0x0 usb-storage: ATAPI Reset: 0x0 usb-storage: ATA Timing: 0x1 usb-storage: ATA Major Command: 0x24 usb-storage: ATA Minor Command: 0x24 usb-storage: Init Status: 0x0 usb-storage: Config Descriptor 2: 0x0 usb-storage: Skip Device Boot: 0x0 usb-storage: ATA 3 State Supsend: 0x0 usb-storage: Descriptor Override: 0x8 usb-storage: Last LUN Identifier: 0x0 usb-storage: SRST Enable: 0x0 usb-storage: usb_stor_ctrl_transfer(): rq=01 rqtype=40 value=0000 index=02 len=8 usb-storage: Status code 0; transferred 8/8 usb-storage: -- transfer complete usb-storage: ISD200 Config Data was written successfully usb-storage: Leaving isd200_write_config 00000000 usb-storage: Leaving isd200_manual_enum 00000000 usb-storage: Protocol changed to: Transparent SCSI usb-storage: Leaving isd200_get_inquiry_data 00000000 usb-storage: ISD200 Initialization complete usb-storage: *** thread sleeping. scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command INQUIRY (6 bytes) usb-storage: 12 00 00 00 24 00 usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 36 F 128 CL 6 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code -32; transferred 31/31 usb-storage: clearing endpoint halt for pipe 0xc0008200 usb-storage: usb_stor_clear_halt: result=0 usb-storage: Bulk command transfer result=2 usb-storage: -- transport indicates error, resetting usb-storage: Bulk reset requested usb-storage: command_abort() called usb-storage: usb_stor_abort_transport called usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 0 F 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk status Sig 0x53425355 T 0x1 R 0 Stat 0x2 usb-storage: -- transport indicates error, resetting usb-storage: Bulk reset requested usb-storage: command_abort() called usb-storage: usb_stor_abort_transport called usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: device_reset() called usb-storage: Bulk reset requested usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Command TEST_UNIT_READY (6 bytes) usb-storage: 00 00 00 00 00 00 usb-storage: Bulk command S 0x43425355 T 0x1 Trg 0 LUN 0 L 0 F 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf(): xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf(): xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk status Sig 0x53425355 T 0x1 R 0 Stat 0x2 usb-storage: -- transport indicates error, resetting usb-storage: Bulk reset requested usb-storage: command_abort() called usb-storage: usb_stor_abort_transport called usb-storage: Soft reset: clearing bulk-in endpoint halt usb-storage: Soft reset: clearing bulk-out endpoint halt usb-storage: Soft reset done usb-storage: scsi cmd done, result=0x70000 usb-storage: *** thread sleeping. usb-storage: bus_reset() called drivers/usb/core/hub.c: USB device not accepting new address (error=-22) usb-storage: usb_reset_device returns -22 scsi: Device offlined - not ready after error recovery: host 0 channel 0 id 0 lun 0 usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (1/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (2/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (3/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (4/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (5/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (6/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand() called usb-storage: *** thread awakened. usb-storage: Bad target number (7/0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2 drivers/usb/core/usb.c: registered new driver usb-storage USB Mass Storage support registered.
The error "USB device not accepting new address" can sometimes be a symptom of an interrupt problem. Do you see interrupts increasing for this device in /proc/interrupts? There is some more info on this in the FAQ at
http://www.linux-usb.org .
Quoted 10 lines · Andrey Panin
Hi,
ISD200 based hard drive bay doesn't work with 2.4 & 2.5, can someone assist me with it?
Kernel message log appended.
Best regards.
Signature · 6 lines
/------------------------------------+-------------------------\ |Stephen J. Gowdy | SLAC, MailStop 34, | |http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, | |http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA | |EMail: [email protected] | Tel: +1 650 926 3144 | \------------------------------------+-------------------------/
Quoted 4 lines · Andrey Panin
Hi,
ISD200 based hard drive bay doesn't work with 2.4 & 2.5, can someone assist me with it?
This looks like the same problem I was seeing with my Archos. The initial probes for ATA devices fail and the driver falls back to 'transparent scsi mode', where it passes everything along unchanged. Probably works fine when an ATAPI device is attached, but not with my drive.
Quoted 9 lines
usb-storage:
isd200_action(ENUM,0xa0)
usb-storage: Bulk command S0x43425355T0x0Trg 0 LUN 1 L 0 F 0 CL 0
usb-storage:usb_stor_bulk_transfer_buf(): xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage:usb_stor_bulk_transfer_buf(): xfer 13 bytes
usb-storage: Status code -32; transferred 0/13
The isd200 driver is not correctly initializing the srb.cmd_len field, which is the main reason why things fail. I also noticed that the usb_stor_bulk functions are interpreting the ATA commands as if they were scsi, so the packet was sent to the wrong lun, but that might not really matter much.
Here is a patch agains 2.5.64 that fixes both of these problems for me. It will probably apply to 2.5.65 as well.
Jan
usb/storage/isd200.c renamed from usb/storage/isd200.c.orig +5 -0
@@ -405,11 +405,14 @@ {union ata_cdb ata;struct scsi_cmnd srb; +struct scsi_device srb_dev;struct isd200_info *info = (struct isd200_info *)us->extra;int status;memset (&ata,0 ,sizeof (ata));memset (&srb,0 ,sizeof (srb)); +memset (&srb_dev,0 ,sizeof (srb_dev)); + srb.device = &srb_dev; ata.generic.SignatureByte0 = info->ConfigData.ATAMajorCommand; ata.generic.SignatureByte1 = info->ConfigData.ATAMinorCommand;
@@ -479,6 +482,7 @@ }memcpy (srb.cmnd, &ata,sizeof (ata.generic)); + srb.cmd_len =sizeof (ata.generic); status =usb_stor_Bulk_transport (&srb, us);if (status ==USB_STOR_TRANSPORT_GOOD ) status =ISD200_GOOD ;
@@ -538,6 +542,7 @@/* send the command to the transport layer */ srb->resid =0 ;memcpy (srb->cmnd, ataCdb,sizeof (ataCdb->generic)); + srb->cmd_len =sizeof (ataCdb->generic); transferStatus =usb_stor_Bulk_transport (srb, us);/* if the command gets aborted by the higher layers, we need to
usb/storage/transport.c renamed from usb/storage/transport.c.orig +1 -1
@@ -893,7 +893,7 @@ bcb.DataTransferLength =cpu_to_le32 (transfer_length); bcb.Flags = srb->sc_data_direction ==SCSI_DATA_READ ?1 <<7 :0 ; bcb.Tag = srb->serial_number; - bcb.Lun = srb->cmnd[1 ] >>5 ; + bcb.Lun = srb->device->lun;if (us->flags &US_FL_SCM_MULT_TARG ) bcb.Lun |= srb->device->id <<4 ; bcb.Length = srb->cmd_len;
Quoted 22 lines · Jan Harkes
Quoted 4 lines · Andrey Panin
Hi,
ISD200 based hard drive bay doesn't work with 2.4 & 2.5, can someone assist me with it?
This looks like the same problem I was seeing with my Archos. The initial probes for ATA devices fail and the driver falls back to 'transparent scsi mode', where it passes everything along unchanged. Probably works fine when an ATAPI device is attached, but not with my drive.
Quoted 9 lines
usb-storage:
isd200_action(ENUM,0xa0)
usb-storage: Bulk command S0x43425355T0x0Trg 0 LUN 1 L 0 F 0 CL 0
usb-storage:usb_stor_bulk_transfer_buf(): xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-storage:usb_stor_bulk_transfer_buf(): xfer 13 bytes
usb-storage: Status code -32; transferred 0/13
Quoted 8 lines
The isd200 driver is not correctly initializing the srb.cmd_len field, which is the main reason why things fail. I also noticed that the
usb_stor_bulkfunctions are interpreting the ATA commands as if they were scsi, so the packet was sent to the wrong lun, but that might not really matter much.Here is a patch agains 2.5.64 that fixes both of these problems for me. It will probably apply to 2.5.65 as well.
I don't have this drive at this time, but i'll test your patch and report results ASAP.
Signature · 2 lines
Andrey Panin | Embedded systems software developer [email protected] | PGP key: wwwkeys.pgp.net