CONFIG_SERIAL_TEXT_DEBUG causes exception
Thanks for the info -
It doesn't look to me like the 4xx has a BAT -
what would I use instead?
Jerry Walden
-----Original Message-----
From: Gary D. Thomas [mailto:[email protected]]
Sent: Wednesday, March 19, 2003 4:19 PM
To: Jerry Walden
Cc: linuxppc embedded
Subject: RE: CONFIG_SERIAL_TEXT_DEBUG causes exception
Quoted 7 lines · Jerry Walden
What other embedded board (hopefully a ppc) would you suggest - I don't see any special provisions in the kernel for a custom mapping of these registers based on a configuration option for any specific board - this appears to be generic code that meant for all platforms - I believe what you say regarding what I have to do:
Quoted 6 lines
1) I can't find sample code that you refer to.
2) I am confused as to why this code is in the kernel in the way it is because it seems to me that most embedded processors have an MMU, so why the comment in that section of code that says "assuming the firmware setup the board properly...."
As soon as the kernel starts, there are *no* mappings, other than RAM, unless explicitly set up.
Try looking at arch/ppc/platforms/pumaA.c (in the 2_4_devel kernel). This explicit mapping happens in the "platform_init" function, near the end.
n.b. it's polite to copy such dialogue to the mailing list so that everyone else can benefit. If you want (or need) private help, you can arrange for it.
Quoted 47 lines
Thanks Much for Your Help
Jerry Walden
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Gary D. Thomas
Sent: Wednesday, March 19, 2003 12:54 PM
To: [email protected]
Cc: linuxppc embedded
Subject: Re:CONFIG_SERIAL_TEXT_DEBUGcauses exceptionQuoted 11 lines · Jerry Walden
Hello:
I have a custom PPC405GPr board that I have successfully ported u-boot to.
I am now at the stage of trying to bring Linux up on the board.
I have
CONFIG_SERIAL_TEXT_DEBUGdefined for the kernel that I am trying to bring up. I would like to have this option so I can trace through the kernel.
The comments inppc4xx_setup.cin the functionserial_putcindicate thatas
Quoted 2 lines
long
as the firmware (in my case u-boot) has been initialized properly, thenthis
Quoted 8 lines
function
should work. I have verified the addresses that the function is trying to write to
and they are correct. However, whenserial_putccalls the first readb, I get an
exception.Can someone please provide some pointers as to what might be wrong?
You need to make sure that the serial registers are mapped at that point. I don't know the details of your U-boot implementation, but the kernel will most certainly not have this region mapped unless you make it happen explicitly. Look at some other embedded boards and you'll find code to set this up, typically using a BAT or some other special mapping.
Quoted 11 lines
--
.--------------------------------------------------------.| Mind: Embedded Linux and eCos Development | |--------------------------------------------------------| | Gary Thomas email: [email protected] | | Mind ( http://mind.be ) tel: +1 (970) 229-1963 | | gpg: http://www.chez-thomas.org/gary/gpg_key.asc |'--------------------------------------------------------'
--
--------------------------------------------------------.
| Mind: Embedded Linux and eCos Development | |--------------------------------------------------------| | Gary Thomas email: [email protected] | | Mind ( http://mind.be ) tel: +1 (970) 229-1963 | | gpg: http://www.chez-thomas.org/gary/gpg_key.asc |
'--------------------------------------------------------'
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Quoted 6 lines · On Wed, 2003-03-19 at 20:05, [email protected] wrote:
Thanks for the info -
It doesn't look to me like the 4xx has a BAT -
what would I use instead?
One way would be to use a locked TLB. I'm sure there are others.
Quoted 94 lines
Jerry Walden
-----Original Message-----
From: Gary D. Thomas [mailto:[email protected]]
Sent: Wednesday, March 19, 2003 4:19 PM
To: Jerry Walden
Cc: linuxppc embedded
Subject: RE:CONFIG_SERIAL_TEXT_DEBUGcauses exceptionQuoted 7 lines · Jerry Walden
What other embedded board (hopefully a ppc) would you suggest - I don't see any special provisions in the kernel for a custom mapping of these registers based on a configuration option for any specific board - this appears to be generic code that meant for all platforms - I believe what you say regarding what I have to do:
Quoted 6 lines
1) I can't find sample code that you refer to.
2) I am confused as to why this code is in the kernel in the way it is because it seems to me that most embedded processors have an MMU, so why the comment in that section of code that says "assuming the firmware setup the board properly...."As soon as the kernel starts, there are *no* mappings, other than RAM, unless explicitly set up.
Try looking at
arch/ppc/platforms/pumaA.c(in the 2_4_devel kernel). This explicit mapping happens in the "platform_init" function, near the end.n.b. it's polite to copy such dialogue to the mailing list so that everyone else can benefit. If you want (or need) private help, you can arrange for it.
Quoted 47 lines
Thanks Much for Your Help
Jerry Walden
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Gary D. Thomas
Sent: Wednesday, March 19, 2003 12:54 PM
To: [email protected]
Cc: linuxppc embedded
Subject: Re:CONFIG_SERIAL_TEXT_DEBUGcauses exceptionQuoted 11 lines · Jerry Walden
Hello:
I have a custom PPC405GPr board that I have successfully ported u-boot to.
I am now at the stage of trying to bring Linux up on the board.
I have
CONFIG_SERIAL_TEXT_DEBUGdefined for the kernel that I am trying to bring up. I would like to have this option so I can trace through the kernel.
The comments inppc4xx_setup.cin the functionserial_putcindicate thatas
Quoted 2 lines
long
as the firmware (in my case u-boot) has been initialized properly, thenthis
Quoted 8 lines
function
should work. I have verified the addresses that the function is trying to write to
and they are correct. However, whenserial_putccalls the first readb, I get an
exception.Can someone please provide some pointers as to what might be wrong?
You need to make sure that the serial registers are mapped at that point. I don't know the details of your U-boot implementation, but the kernel will most certainly not have this region mapped unless you make it happen explicitly. Look at some other embedded boards and you'll find code to set this up, typically using a BAT or some other special mapping.
Quoted 11 lines
--
.--------------------------------------------------------.| Mind: Embedded Linux and eCos Development | |--------------------------------------------------------| | Gary Thomas email: [email protected] | | Mind ( http://mind.be ) tel: +1 (970) 229-1963 | | gpg: http://www.chez-thomas.org/gary/gpg_key.asc |'--------------------------------------------------------'
Quoted 9 lines
--
--------------------------------------------------------.| Mind: Embedded Linux and eCos Development | |--------------------------------------------------------| | Gary Thomas email: [email protected] | | Mind ( http://mind.be ) tel: +1 (970) 229-1963 | | gpg: http://www.chez-thomas.org/gary/gpg_key.asc |'--------------------------------------------------------'
--
.--------------------------------------------------------.
| Mind: Embedded Linux and eCos Development | |--------------------------------------------------------| | Gary Thomas email: [email protected] | | Mind ( http://mind.be ) tel: +1 (970) 229-1963 | | gpg: http://www.chez-thomas.org/gary/gpg_key.asc |
'--------------------------------------------------------'
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/