addition to visor.c
First off, hi all and thanks for all the kernels. :D
I have fiddled together the following info for a sony clie nz90, which i believe should go in drivers/usb/serial/visor.{h,c}.
in visor.h:
#define SONY_CLIE_NZ90_ID 0x00E9
and in visor.c:
{ USB_DEVICE(SONY_VENDOR_ID, SONY_CLIE_NZ90_ID) },
in two places, both after the line
{ USB_DEVICE(SONY_VENDOR_ID, SONY_CLIE_4_1_ID) },
this is almost definitely an awful way of submitting these, but this is my first ever attempt at kernel hacking (and it barely counts as such (and it barely counts as something that barely counts...)) so please don't flame me too hard.
it just compiled, and assuming it boots && recognizes the device, i'll send this.
ok, it recognizes, but none of the apps i have seem to like the clie - i get 'please press hotsync button now' messages, despite the fact that the /dev/ttyUSB1 device is only there after the button has been pressed... :(
my sister's clie cries out for breakout, and an internet...
cheers,
iain
(scared and tired and wanting to PLAY WITH MY SISTER'S NEW CLIE DAMMIT :p)
PS: please CC: me on replies, i'm subscribed but have a tendency to not spot list replies. thanks.
Signature · 1 line
wh33, y1p33 3tc.
Quoted 4 lines · iain d broadfoot
First off, hi all and thanks for all the kernels. :D
I have fiddled together the following info for a sony clie nz90, which i believe should go in
drivers/usb/serial/visor.{h,c}.
Thanks, but this device is already supported in the latest 2.5 kernel :)
And it's in my queue of patches to send to Marcelo for 2.4, so it will show up there too eventually.
Quoted 4 lines
ok, it recognizes, but none of the apps i have seem to like the clie - i get 'please press hotsync button now' messages, despite the fact that the
/dev/ttyUSB1device is only there after the button has been pressed... :(
Try the latest version of pilot-link, from pilot-link.org. You need that. If that doesn't work, try ttyUSB0, that might be the correct port for this device.
Thanks,
greg k-h
Quoted 7 lines · * Greg KH ([email protected]) wrote:
Quoted 4 lines · iain d broadfoot
First off, hi all and thanks for all the kernels. :D
I have fiddled together the following info for a sony clie nz90, which i believe should go in
drivers/usb/serial/visor.{h,c}.Thanks, but this device is already supported in the latest 2.5 kernel :)
ah. ok-dok. :(
i felt so proud and manly and super-cool as well...
Quoted 3 lines
And it's in my queue of patches to send to Marcelo for 2.4, so it will show up there too eventually.
sweet.
i just need to remember not to bunzip the kernel source over my version now...
Quoted 9 lines
Quoted 5 lines
ok, it recognizes, but none of the apps i have seem to like the clie - i get 'please press hotsync button now' messages, despite the fact that the
/dev/ttyUSB1device is only there after the button has been pressed... :(Try the latest version of pilot-link, from pilot-link.org. You need that. If that doesn't work, try ttyUSB0, that might be the correct port for this device.
hmm, i've got the latest pilot-link, and i've tried both 0 and 1 (0 gets logged as the Generic, while 1 is logged as HotSync) so i think it's time to find a new list to harass. :D
cheers,
iain
Signature · 1 line
wh33, y1p33 3tc.
Quoted 3 lines · iain d broadfoot
PS: please CC: me on replies, i'm subscribed but have a tendency to not spot list replies. thanks.
Then don't set the Reply-To: field to only point to the list, as it's a bit tougher for responses to get to you :)
greg k-h