avm fritz pci
I have kernel 2.4.21-rc2 (I also tested 2.4.20 2.4.21-pre6, pre7 and rc1) and when I use 2 channels connect, system crash. Hisax modul is loaded with parametrs:
modprobe hisax protocol=2 type=27
System: Slackware 9.0
gcc 3.2.3 (only 2.4.21-rc2 was compiled by this version, rest by gcc-3.2.2 from slackware package)
isdn4k-utils-3.2p1
[root@slack:~#] lspci -vvv
00:0b.0 Network controller: AVM Audiovisuelles MKTG & Computer System
GmbH A1 ISDN [Fritz] (rev 02) Subsystem: AVM Audiovisuelles MKTG &
Computer System GmbH FRITZ!Card ISDN Controller Control: I/O+ Mem+ BusMaster-
SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap-
66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort-
Quoted 1 line
SERR- <PERR-
Interrupt: pin A routed to IRQ 5 Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=32] Region 1: I/O ports at 7400 [size=32]
Signature · 3 lines
registered Linux user 261525 | Wszystko jest trudne przy gg [email protected]| odpowiednim stopniu RMRMG signature version 0.0.2| abstrakcji
begin Rafał 'rmrmg' Roszak <[email protected]> quote:
Quoted 5 lines
I have kernel 2.4.21-rc2 (I also tested 2.4.20 2.4.21-pre6, pre7 and rc1) and when I use 2 channels connect, system crash. Hisax modul is loaded with parametrs:
modprobe hisax protocol=2 type=27
I have this problem also in 2.4.21-rc3
I compilded kernel with MAGIC_SYSRQ but I can't reboot system after crash use Alt+PrtScr+[s,u,b] ...
Signature · 3 lines
registered Linux user 261525 | Wszystko jest trudne przy gg [email protected]| odpowiednim stopniu RMRMG signature version 0.0.2| abstrakcji
Quoted 10 lines · Rafał 'rmrmg' Roszak
begin Rafał 'rmrmg' Roszak <[email protected]> quote:
Quoted 5 lines
I have kernel 2.4.21-rc2 (I also tested 2.4.20 2.4.21-pre6, pre7 and rc1) and when I use 2 channels connect, system crash. Hisax modul is loaded with parametrs:
modprobe hisax protocol=2 type=27
Quoted 3 lines
I have this problem also in 2.4.21-rc3
I compilded kernel withMAGIC_SYSRQbut I can't reboot system after crash use Alt+PrtScr+[s,u,b] ...
Did you enable SysRq with
echo 1 >/proc/sys/kernel/sysrq
If so, can you test if sysrq works while the system is not crashed?
In case SysRq doesn't work only after this crash, can you compile in the NMI watchdog and boot with parameter
nmi_watchdog=1
That should print a backtrace if your system hangs hard and SysRq does not work.
NOTE 1: You can see the backtrace only if you are not using X at that time. NOTE 2: Your system will be dead after the NMI watchdog triggers. Please write down the backtrace and pass it through ksymoops.
Regards,
Carl-Daniel
Signature · 1 line
http://www.hailfinger.org/
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 17 lines · Rafał 'rmrmg' Roszak
begin Carl-Daniel Hailfinger <[email protected]> quote:
Quoted 2 lines
Did you enable SysRq with
echo 1 >/proc/sys/kernel/sysrqdefault is 1 in this file
Quoted 1 line
If so, can you test if sysrq works while the system is not crashed?
yes, sysrq works
Quoted 6 lines
Quoted 2 lines
In case SysRq doesn't work only after this crash, can you compile in the NMI watchdog and boot with parameter
sorry I can't find this in make menuconfig
Could you help me?
It will be compiled in automatically if you select "Local APIC Support on Uniprocessors" and "IO-APIC support on uniprocessors", then boot with
nmi_watchdog=1
If your system hangs for longer than 5 seconds, the NMI watchdog will print a backtrace on the console.
HTH,
Carl-Daniel
Signature · 1 line
http://www.hailfinger.org/
Quoted 4 lines · Carl-Daniel Hailfinger
It will be compiled in automatically if you select "Local APIC Support on Uniprocessors" and "IO-APIC support on uniprocessors", then boot with
nmi_watchdog=1
He'd have more luck with nmi_watchdog=2 on UP (not a lot of UP motherboards have IOAPICs)
Zwane
Signature · 1 line
function.linuxpower.ca
begin Zwane Mwaikambo <[email protected]> quote:
Quoted 7 lines
Quoted 4 lines
It will be compiled in automatically if you select "Local APIC Support on Uniprocessors" and "IO-APIC support on uniprocessors", then boot with
nmi_watchdog=1He'd have more luck with nmi_watchdog=2 on UP (not a lot of UP motherboards have IOAPICs)
[root@slack:~#] dmesg | less
Kernel command line: vga=791 hdc=ide-scsi nmi_watchdog=2ide_setup: hdc=ide-scsi
No local APIC present or hardware disabled
my motherboard is aopen ax59pro
SysRq and NMI doesn't works
system crash after start download when use 2channel connection
Signature · 3 lines
registered Linux user 261525 | Wszystko jest trudne przy gg [email protected]| odpowiednim stopniu RMRMG signature version 0.0.2| abstrakcji