Hercules Gamesurround Fortissimo III 7.1
Hi...
During the last weeks, I tried to get that card to work with ALSA 0.9.3c. Here's what I found:
- The card is not properly recognized by the driver. I added the card to the
drivers hardware list (see attached patch) which seemed to help somewhat.
- Without the external_amp parameter, sound is sometimes OK, sometimes
distorted, sometimes not available at all.
- With external_amp set, the card basically works, but there are some quirks
The remaining quirks are:
- After a cold boot, the driver loads OK. After some 2-3 minutes uptime,
there's a very loud crackling noise, independent of sound output (like very high spikes in the output). This goes away after about 20 seconds. After that, sound is either "normal" (definition of normal follows...) or entirely gone.
- Unloading the driver module works. However, reloading the module fails the
first time. Trying to load the driver a second time is always successful. See the "reload-module.txt" attachment for output.
- Sometimes, sound is distorted at high PCM volume settings, sometimes it
isn't. I have not found any way to reproduce this, it just happens from time to time. (Lasts as long as the machine isn't power-cycled). Setting the PCM volume down to about 77% avoids this.
- After rebooting from Windows, sound dies with a "plop" afer some minutes.
Reloading the module gives another few minutes of sound. (repeat ad nauseam)
In conclusion, I think there's something wrong with the initialization. My configuration is similar to the one given on the alsa-project website. Are there any known bugs or workarounds?
Signature · 1 line
Got Backup?
home/nicos/systemcode/alsa-driver-0.9.3c/alsa-kernel/pci/cs46xx/cs46xx_lib.c renamed from alsa-driver/alsa-kernel/pci/cs46xx/cs46xx_lib.c +7 -0
@@ -3743,6 +3743,13 @@ .amp = amp_hercules, .mixer_init = hercules_mixer_init, }, + { + .vendor = 0x1681, + .id = 0xa011, + .name = "Hercules Fortissimo III 7.1", + .amp = amp_hercules, + .mixer_init = hercules_mixer_init, + },/* Teratec */ { .vendor = 0x153b,
--- loading the module after unloading ---
elysium:~# modprobe snd-cs46xx
Warning: ignoring device_gid=29, no such parameter in this module
Warning: ignoring device_uid=0, no such parameter in this module
Module snd loaded, with warnings
Module snd-seq-device loaded, with warnings
Module snd-rawmidi loaded, with warnings
Module snd-timer loaded, with warnings
Module snd-pcm loaded, with warnings
Module snd-ac97-codec loaded, with warnings
/lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o: init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters.
You may find more information in syslog or the output from dmesg
/lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o: insmod /lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o failed
/lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o: insmod snd-cs46xx failed
elysium:~# modprobe snd-cs46xx
Warning: ignoring device_gid=29, no such parameter in this module
Warning: ignoring device_uid=0, no such parameter in this module
Module snd loaded, with warnings
Module snd-seq-device loaded, with warnings
Module snd-rawmidi loaded, with warnings
Module snd-timer loaded, with warnings
Module snd-pcm loaded, with warnings
Module snd-ac97-codec loaded, with warnings
Module snd-cs46xx loaded, with warnings--- dmesg ---
PCI: Found IRQ 5 for device 00:0f.0
ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:416: cs46xx: failure waiting for FIFO command to complete ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3216: ERROR: snd-cs46xx: never read ISV3 & ISV4 from AC'97
ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3217: Try reloading the ALSA driver, if you find something ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3218: broken or not working on your soundcard upon ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3219: this message please report to [email protected]
Sound Fusion CS46xx soundcard not found or device busy
PCI: Found IRQ 5 for device 00:0f.0
ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:416: cs46xx: failure waiting for FIFO command to complete
Quoted 2 lines · Nicos Gollan
- With
external_ampset, the card basically works, but there are some
quirks
OK, forget about that. The card just decided to always drop dead after about a minute, no matter what I'm doing even after a cold boot. Without me changing the configuration. Great.
Signature · 9 lines
Got Backup? ------------------------------------------------------- This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET. http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01
Quoted 8 lines
- Without the
external_ampparameter, sound is sometimes OK, sometimes distorted, sometimes not available at all.- With
external_ampset, the card basically works, but there are some quirks
But, amp_hercules(...) and hercules_mixer_init(...) function have only been implemented to do some specific initializations to the Game Theater XP card, which probably is very similar to the Fortissimo card, but my guess is that something slight diferenent is needed on the initialization phase. (which can be hard to know course Hercules seems to be yet another company which dont releases any spec. about their soundcards ....)
If you say that it works better with the external_amp=1, then this card must have some similarity with the Santa Cruz card ... the amp_voyectra(...) function will also set some GPIO's on the seconary cs4294 codec, who knows if this is good or bad for the Fortissimo card ....
Quoted 7 lines
- After a cold boot, the driver loads OK. After some 2-3 minutes uptime,
there's a very loud crackling noise, independent of sound output (like very high spikes in the output). This goes away after about 20 seconds. After that, sound is either "normal" (definition of normal follows...) or entirely gone.- Unloading the driver module works. However, reloading the module fails the
first time. Trying to load the driver a second time is always successful. See the "reload-module.txt" attachment for output.
This card is not the only one that has initialization problems, I've got similar problems with the Terratec SixPack 5.1. Some of the initialization problems could probably be fixed having some time and pacience.
The other sound problems you're talking about seems to be new to the Fortissimo card ...
Quoted 4 lines
- Sometimes, sound is distorted at high PCM volume settings, sometimes it
isn't. I have not found any way to reproduce this, it just happens from time to time. (Lasts as long as the machine isn't power-cycled). Setting the PCM volume down to about 77% avoids this.
Well, and thoose distortion problems with cs46xx are not new either. Try having the master volume at 100% and 3D settings to "Post 3D" then play with the PCM volume, and check what's the behaviour.
Quoted 4 lines
- After rebooting from Windows, sound dies with a "plop" afer some minutes. Reloading the module gives another few minutes of sound. (repeat ad nauseam)
Who knows what the Windows driver does with the HW that the ALSA driver dont ....
What about the other functions on the card:
Have you tested the SPDIF output/input AC3 pass-through? the different outputs, center, rear, surround speakers ?
/Benny
Quoted 53 lines
------------------------------------------------------------------------
home/nicos/systemcode/alsa-driver-0.9.3c/alsa-kernel/pci/cs46xx/cs46xx_lib.c renamed from alsa-driver/alsa-kernel/pci/cs46xx/cs46xx_lib.c +7
-2@@ -3743,6 +3743,13 @@ .amp = amp_hercules, .mixer_init = hercules_mixer_init, }, + { + .vendor = 0x1681, + .id = 0xa011, + .name = "Hercules Fortissimo III 7.1", + .amp = amp_hercules, + .mixer_init = hercules_mixer_init, + },/* Teratec */ { .vendor = 0x153b, ------------------------------------------------------------------------ --- loading the module after unloading ---elysium:~# modprobe snd-cs46xx Warning: ignoring device_gid=29, no such parameter in this module Warning: ignoring device_uid=0, no such parameter in this module Module snd loaded, with warnings Module snd-seq-device loaded, with warnings Module snd-rawmidi loaded, with warnings Module snd-timer loaded, with warnings Module snd-pcm loaded, with warnings Module snd-ac97-codec loaded, with warnings /lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o: insmod /lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o failed /lib/modules/2.4.21-personal-alsa/alsa/snd-cs46xx.o: insmod snd-cs46xx failed elysium:~# modprobe snd-cs46xx Warning: ignoring device_gid=29, no such parameter in this module Warning: ignoring device_uid=0, no such parameter in this module Module snd loaded, with warnings Module snd-seq-device loaded, with warnings Module snd-rawmidi loaded, with warnings Module snd-timer loaded, with warnings Module snd-pcm loaded, with warnings Module snd-ac97-codec loaded, with warnings Module snd-cs46xx loaded, with warnings--- dmesg ---
PCI: Found IRQ 5 for device 00:0f.0
ALSA../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:416: cs46xx: failure waiting for FIFO command to complete ALSA../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3216: ERROR: snd-cs46xx: never read ISV3 & ISV4 from AC'97
Quoted 8 lines
ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3217: Try reloading the ALSA driver, if you find something ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3218: broken or not working on your soundcard upon ALSA ../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:3219: this message please report to [email protected]Sound Fusion CS46xx soundcard not found or device busy
PCI: Found IRQ 5 for device 00:0f.0
ALSA../../alsa-kernel/pci/cs46xx/cs46xx_lib.c:416: cs46xx: failure waiting for FIFO command to complete
-------------------------------------------------------
This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET.
http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01
Quoted 9 lines · Benny Sjostrand
But,
amp_hercules(...)andhercules_mixer_init(...)function have only been implemented to do some specific initializations to the Game Theater XP card, which probably is very similar to the Fortissimo card, but my guess is that something slight diferenent is needed on the initialization phase. [...]
If you say that it works better with the external_amp=1, then this card must have some similarity with the Santa Cruz card ... theamp_voyectra(...)function will also set some GPIO's on the seconary cs4294 codec, who knows if this is good or bad for the Fortissimo card ....
It worked for some time (with the mentioned distortion and crackling but seems to have stopped working now. Sound now dies after about a minute from module load, even after a cold reboot. Behaviour now is the same independent from external_amp. I don't have the slightest idea why this is so. I had the machine switched off for a week, turned it on and it was like this. The only thing that changed is the VGA card, but it does the same thing even in pure text mode, without DRM drivers or AGPGART modules loaded.
So in conclusion, I can only say that external_amp was good for the card but only for some time :-/
Also, the problems now seem to be somewhat independent from Windows drivers having seen the card before. In the past, I had all kinds of different side effects, ranging from the card running better after a reboot from Windows to complete inactivity.
Quoted 3 lines
What about the other functions on the card:
Have you tested the SPDIF output/input AC3 pass-through?
the different outputs, center, rear, surround speakers ?
Sorry, I don't have any hardware that knows SPDIF. The analog speaker outputs all seemed to be dead.
Signature · 9 lines
Got Backup? ------------------------------------------------------- This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET. http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01
Quoted 27 lines · Nicos Gollan
Quoted 9 lines · Benny Sjostrand
But,
amp_hercules(...)andhercules_mixer_init(...)function have only been implemented to do some specific initializations to the Game Theater XP card, which probably is very similar to the Fortissimo card, but my guess is that something slight diferenent is needed on the initialization phase. [...]
If you say that it works better with the external_amp=1, then this card must have some similarity with the Santa Cruz card ... theamp_voyectra(...)function will also set some GPIO's on the seconary cs4294 codec, who knows if this is good or bad for the Fortissimo card ....It worked for some time (with the mentioned distortion and crackling but seems to have stopped working now. Sound now dies after about a minute from module load, even after a cold reboot. Behaviour now is the same independent from
external_amp. I don't have the slightest idea why this is so. I had the machine switched off for a week, turned it on and it was like this. The only thing that changed is the VGA card, but it does the same thing even in pure text mode, without DRM drivers or AGPGART modules loaded.So in conclusion, I can only say that
external_ampwas good for the card but only for some time :-/Also, the problems now seem to be somewhat independent from Windows drivers having seen the card before. In the past, I had all kinds of different side effects, ranging from the card running better after a reboot from Windows to complete inactivity.
Quoted 7 lines
Quoted 3 lines
What about the other functions on the card:
Have you tested the SPDIF output/input AC3 pass-through?
the different outputs, center, rear, surround speakers ?Sorry, I don't have any hardware that knows SPDIF. The analog speaker outputs all seemed to be dead.
Are you sure it's not just the card that is dead/dying? I've been running the card since last year without any problems, except the "distortion at full pcm volume" problem.
Signature · 8 lines
Ronny V. Vindenes <[email protected]> ------------------------------------------------------- This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET. http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01
Quoted 3 lines · Ronny V. Vindenes
Are you sure it's not just the card that is dead/dying? I've been running the card since last year without any problems, except the "distortion at full pcm volume" problem.
The card is working perfectly in Windows, no matter what I do (music, games, ...). The only time that I saw similar problemis in Windows was when I had the card running with the stock drivers (Win2k, SP3) where sound was dying after a short time, but that was solved with the drivers on the CD. So I don't think it's a hardware problem.
Or perhaps it is a known problem that the drivers can work around.
Signature · 9 lines
Got Backup? ------------------------------------------------------- This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET. http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01
Quoted 8 lines
Quoted 7 lines
Are you sure it's not just the card that is dead/dying? I've been running the card since last year without any problems, except the "distortion at full pcm volume" problem.
Quoted 5 lines
The card is working perfectly in Windows, no matter what I do (music, games, ...). The only time that I saw similar problemis in Windows was when I had the card running with the stock drivers (Win2k, SP3) where sound was dying after a short time, but that was solved with the drivers on the CD. So I don't think it's a hardware problem.
Or perhaps it is a known problem that the drivers can work around.
Maybe the problem is not in the alsa-driver, maybe it's something else related to another comoponent of the kernel, PCI-bridge/ctrl ...
Is the soundcard the only thing causing problems in your system ??
/Benny
-------------------------------------------------------
This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET.
http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01
Quoted 5 lines · Benny Sjostrand
Maybe the problem is not in the alsa-driver, maybe it's something else related to
another comoponent of the kernel, PCI-bridge/ctrl ...Is the soundcard the only thing causing problems in your system ??
Yes, it is. And now that I've changed to a Creative SB Live 5.1, all is working fine.
Just a thought: could it be a problem with power management sending the card to sleep? If so, how could I avoid this (apart from disabling APM et al. everywhere I see it mentioned)?
Signature · 9 lines
Got Backup? ------------------------------------------------------- This SF.Net email sponsored by: Free pre-built ASP.NET sites including Data Reports, E-commerce, Portals, and Forums are available now. Download today and enter to win an XBOX or Visual Studio .NET. http://aspnet.click-url.com/go/psa00100006ave/direct;at.asp_061203_01/01