Skip to contentSkip to conversation

Realtek network card

DISCUSSION Stephan von Krawczynski 5 participants 5 messages Aug 13, 2003

lore
Share & tools
lore

Stephan von Krawczynski

author
#0 lore raw

Hello all,

does anybody know how to make the below work (neiter 2.2.25 nor 2.4.21 seem to recognise it):

lspci --vv:

00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8131 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd.: Unknown device 8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 min, 64 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800
Region 1: Memory at ee000000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Regards,
Stephan

#1 lore raw
Quoted 4 lines · Stephan von Krawczynski

Hello all,

does anybody know how to make the below work (neiter 2.2.25 nor 2.4.21 seem to recognise it):

Try modprobe 8139too
(if you are using a precompiled kernel you should have the driver its quite standard, otherwise make sure that you are building it).

Quoted 22 lines

lspci --vv:

00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8131 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd.: Unknown device 8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 min, 64 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800
Region 1: Memory at ee000000 (32-bit, non-prefetchable)
Capabilities: [50] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Regards,
Stephan
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Signature · 2 lines
Micha Feigin
[email protected]
#2 lore raw
In reply to Stephan von Krawczynski
Quoted 8 lines · Stephan von Krawczynski

Hello all,

does anybody know how to make the below work (neiter 2.2.25 nor 2.4.21 seem to recognise it):

lspci --vv:

00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8131 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd.: Unknown device 8139

The subsystem device id seems to indicate 8139, so you probably just need to add pci ids to 8139too.c.

Jeff

#3 lore raw
Quoted 8 lines · Jeff Garzik
Quoted 2 lines

00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8131 (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd.: Unknown device 8139

The subsystem device id seems to indicate 8139, so you probably just need to add pci ids to 8139too.c.

Jeff

8139 - 8131 = 8, think he might have the same problem i had a while ago that you found, where the card just wasn't inserted right, and one bit was off?

Mike

#4 lore raw
In reply to Stephan von Krawczynski
Quoted 10 lines · Stephan von Krawczynski

Hello all,

does anybody know how to make the below work (neiter 2.2.25 nor 2.4.21 seem to recognise it):

lspci --vv:

00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd.: Unknown device 8131 (rev 10) Subsystem: Realtek Semiconductor Co., Ltd.: Unknown device 8139

Do you know what make and model the card actually is? I know it what it appears to be, but it'd be best to know for sure.

Signature · 1 line
Ian.