Problem with 2.6-testXX and alcatel speedtouch usb modem
I try to make this modem working.
It works very well on kernel 2.4 series.
It work with some kernel 2.6 until test2-mm1.
But since test2-mm1, the newer kernel doesn't work anymore. There is 2 related drivers for this modem.
The one which is included in the kernel and which can be found here :
http://www.linux-usb.org/SpeedTouch/
and the one which I've always used until now :
speedtouch.sourceforge.net
when I notice that the old one doesn't work anymore, I try with the driver which included in the kernel, without success.
It crashed when I do "pppd call adsl".
I can load the firmware.
And here is messages in syslog :
Aug 19 22:00:26 serveur modem_run[337]: modem_run version 1.1 started by root uid 0 Aug 19 22:00:28 serveur kernel: usb 1-2: bulk timeout on ep5in Aug 19 22:00:28 serveur kernel: usbfs: USBDEVFS_BULK failed dev 2 ep 0x85 len 512 ret -110 Aug 19 22:00:43 serveur modem_run[337]: ADSL synchronization has been obtained Aug 19 22:00:43 serveur modem_run[337]: ADSL line is up (608 kbit/s down | 160 kbit/s up) Aug 19 22:00:43 serveur modprobe: FATAL: Module ipv6 not found. Aug 19 22:00:43 serveur pppd[345]: pppd 2.4.1 started by root, uid 0 Aug 19 22:00:43 serveur pppd[345]: Using interface ppp0 Aug 19 22:00:44 serveur pppd[345]: Connect: ppp0 <--> /dev/pts/0 Aug 19 22:00:44 serveur kernel: ip_conntrack version 2.1 (768 buckets, 6144 max) - 300 bytes per conntrack Aug 19 22:00:44 serveur pppoa3[346]: PPPoA3 version 1.1 started by root (uid 0) Aug 19 22:00:44 serveur pppoa3[346]: Control thread ready Aug 19 22:00:44 serveur pppoa3[352]: ppp(d) --> pppoa3 --> modem stream ready Aug 19 22:00:44 serveur pppoa3[353]: modem --> pppoa3 --> ppp(d) stream ready Aug 19 22:00:44 serveur pppoa3[353]: Error reading usb urb Aug 19 22:00:44 serveur pppoa3[346]: Woken by a sem_post event -> Exiting Aug 19 22:00:44 serveur pppoa3[346]: Read from ppp Canceled Aug 19 22:00:44 serveur pppoa3[346]: Write to ppp Canceled Aug 19 22:00:44 serveur pppoa3[346]: Exiting Aug 19 22:00:44 serveur pppd[345]: Modem hangup Aug 19 22:00:44 serveur pppd[345]: Connection terminated. Aug 19 22:00:44 serveur kernel: usbfs: usb_submit_urb returned -32 Aug 19 22:00:44 serveur kernel: Device class 'ppp0' does not have a release() function, it is broken and must be fixed. Aug 19 22:00:44 serveur kernel: Badness in class_dev_release at drivers/base/class.c:201 Aug 19 22:00:44 serveur kernel: Call Trace: Aug 19 22:00:44 serveur kernel: [kobject_cleanup+54/64] kobject_cleanup+0x36/0x40 Aug 19 22:00:44 serveur kernel: [netdev_run_todo+267/464] netdev_run_todo+0x10b/0x1d0 Aug 19 22:00:44 serveur kernel: [_end+114517535/1070384712] ppp_shutdown_interface+0x87/0xe0 [ppp_generic] Aug 19 22:00:44 serveur kernel: [_end+114504362/1070384712] ppp_ioctl+0x802/0x820 [ppp_generic] Aug 19 22:00:44 serveur kernel: [__fput+193/288] __fput+0xc1/0x120 Aug 19 22:00:44 serveur kernel: [sys_ioctl+263/640] sys_ioctl+0x107/0x280 Aug 19 22:00:44 serveur kernel: [syscall_call+7/11] syscall_call+0x7/0xb Aug 19 22:00:44 serveur kernel: Aug 19 22:00:44 serveur kernel: ip_tables: (C) 2000-2002 Netfilter core team Aug 19 22:00:44 serveur pppd[345]: Using interface ppp0 Aug 19 22:00:44 serveur pppd[345]: Connect: ppp0 <--> /dev/pts/0 Aug 19 22:00:44 serveur pppoa3[364]: PPPoA3 version 1.1 started by root (uid 0) Aug 19 22:00:44 serveur pppoa3[364]: Control thread ready Aug 19 22:00:44 serveur pppoa3[374]: ppp(d) --> pppoa3 --> modem stream ready Aug 19 22:00:44 serveur pppoa3[375]: modem --> pppoa3 --> ppp(d) stream ready Aug 19 22:00:44 serveur pppoa3[375]: Error reading usb urb Aug 19 22:00:44 serveur pppoa3[364]: Woken by a sem_post event -> Exiting Aug 19 22:00:44 serveur pppoa3[364]: Read from ppp Canceled Aug 19 22:00:44 serveur pppoa3[364]: Write to ppp Canceled Aug 19 22:00:44 serveur kernel: usbfs: usb_submit_urb returned -32 Aug 19 22:00:44 serveur pppoa3[364]: Exiting Aug 19 22:00:44 serveur pppd[345]: Modem hangup Aug 19 22:00:44 serveur pppd[345]: Connection terminated. Aug 19 22:00:44 serveur kernel: Device class 'ppp0' does not have a release() function, it is broken and must be fixed. Aug 19 22:00:44 serveur kernel: Badness in class_dev_release at drivers/base/class.c:201 Aug 19 22:00:44 serveur kernel: Call Trace: Aug 19 22:00:44 serveur kernel: [kobject_cleanup+54/64] kobject_cleanup+0x36/0x40 Aug 19 22:00:44 serveur kernel: [netdev_run_todo+267/464] netdev_run_todo+0x10b/0x1d0 Aug 19 22:00:44 serveur kernel: [_end+114517535/1070384712] ppp_shutdown_interface+0x87/0xe0 [ppp_generic] Aug 19 22:00:44 serveur kernel: [_end+114504362/1070384712] ppp_ioctl+0x802/0x820 [ppp_generic] Aug 19 22:00:44 serveur kernel: [__fput+193/288] __fput+0xc1/0x120 Aug 19 22:00:44 serveur kernel: [sys_ioctl+263/640] sys_ioctl+0x107/0x280 Aug 19 22:00:44 serveur kernel: [syscall_call+7/11] syscall_call+0x7/0xb Aug 19 22:00:44 serveur kernel: Aug 19 22:00:44 serveur pppoa3[386]: PPPoA3 version 1.1 started by root (uid 0) Aug 19 22:00:44 serveur pppoa3[386]: Control thread ready Aug 19 22:00:44 serveur pppoa3[389]: ppp(d) --> pppoa3 --> modem stream ready Aug 19 22:00:44 serveur pppoa3[390]: modem --> pppoa3 --> ppp(d) stream ready Aug 19 22:00:44 serveur pppoa3[390]: Error reading usb urb Aug 19 22:00:44 serveur pppoa3[386]: Woken by a sem_post event -> Exiting Aug 19 22:00:44 serveur pppoa3[386]: Read from ppp Canceled Aug 19 22:00:44 serveur pppoa3[386]: Write to ppp Canceled Aug 19 22:00:44 serveur kernel: usbfs: usb_submit_urb returned -32 Aug 19 22:00:44 serveur pppd[345]: Using interface ppp0 Aug 19 22:00:44 serveur pppoa3[386]: Exiting Aug 19 22:00:44 serveur pppd[345]: Connect: ppp0 <--> /dev/pts/0 Aug 19 22:00:44 serveur pppd[345]: ioctl(PPPIOCSASYNCMAP): Inappropriate ioctl for device(25) Aug 19 22:00:44 serveur pppd[345]: tcflush failed: Input/output error Aug 19 22:00:44 serveur kernel: Device class 'ppp0' does not have a release() function, it is broken and must be fixed. Aug 19 22:00:44 serveur kernel: Badness in class_dev_release at drivers/base/class.c:201 Aug 19 22:00:44 serveur kernel: Call Trace: Aug 19 22:00:44 serveur kernel: [kobject_cleanup+54/64] kobject_cleanup+0x36/0x40 Aug 19 22:00:44 serveur kernel: [netdev_run_todo+267/464] netdev_run_todo+0x10b/0x1d0 Aug 19 22:00:45 serveur kernel: [_end+114517535/1070384712] ppp_shutdown_interface+0x87/0xe0 [ppp_generic] Aug 19 22:00:45 serveur kernel: [_end+114504362/1070384712] ppp_ioctl+0x802/0x820 [ppp_generic] Aug 19 22:00:45 serveur kernel: [__fput+193/288] __fput+0xc1/0x120 Aug 19 22:00:45 serveur kernel: [sys_ioctl+263/640] sys_ioctl+0x107/0x280 Aug 19 22:00:45 serveur kernel: [syscall_call+7/11] syscall_call+0x7/0xb Aug 19 22:00:45 serveur kernel: Aug 19 22:00:45 serveur pppd[345]: Exit.
so, the last kernel which work with this adsl modem is test2-mm1. here is some informations when I'm running this kernel :
/proc/modules :ipt_state 1248 12 - Live 0xc70d8000ipt_multiport 1408 3 - Live 0xc70d6000ipt_MASQUERADE 2656 1 - Live 0xc70d4000iptable_filter 1952 1 - Live 0xc70cb000ip_nat_irc 3248 0 - Live 0xc70c9000ip_conntrack_irc 70100 1 ip_nat_irc, Live 0xc70b6000ip_nat_ftp 3824 0 - Live 0xc704d000iptable_nat 19436 4 ipt_MASQUERADE,ip_nat_irc,ip_nat_ftp, Live 0xc70a4000 ip_tables 15328 5 ipt_state,ipt_multiport,ipt_MASQUERADE,iptable_filter,iptable_nat, Live 0xc70aa000ip_conntrack_ftp 70708 1 ip_nat_ftp, Live 0xc7091000ip_conntrack 24336 7 ipt_state,ipt_MASQUERADE,ip_nat_irc,ip_conntrack_irc,ip_nat_ftp,iptable_nat,ip_conntrack_ftp, Live 0xc706f000n_hdlc 8228 1 - Live 0xc706b000ppp_async 8992 0 - Live 0xc705e000ppp_synctty 7040 1 - Live 0xc7015000ppp_generic 26416 6 ppp_async,ppp_synctty, Live 0xc7063000
slhc 5984 1 ppp_generic, Live 0xc7039000ohci_hcd 16064 0 - Live 0xc7048000
usbcore 92412 3 ohci_hcd, Live 0xc7076000
vfat 12448 0 - Live 0xc7043000
fat 39040 1 vfat, Live 0xc704f000
8139too 20064 0 - Live 0xc703d000
mii 3712 1 8139too, Live 0xc701a000
crc32 3776 1 8139too, Live 0xc7018000
unix 22064 16 - Live 0xc701d000
lspci -vvv :
00:00.0 Host bridge: Intel Corp. 430TX - 82439TX MTXC (rev 01)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at f000 [size=16]00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 6400 [size=32]00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 01)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:12.0 USB Controller: OPTi Inc. 82C861 (rev 10) (prog-if 10 [OHCI])
Subsystem: OPTi Inc. 82C861
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e3001000 (32-bit, non-prefetchable) [size=4K]
00:13.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at 6800 [size=256]
Region 1: Memory at e3000000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=64K]00:14.0 VGA compatible controller: Matrox Graphics, Inc. MGA 1064SG [Mystique] (rev 02) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 0
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=16K]
Region 1: Memory at e1000000 (32-bit, prefetchable) [size=8M]
Region 2: Memory at e2000000 (32-bit, non-prefetchable) [size=8M]
Expansion ROM at <unassigned> [disabled] [size=64K]Quoted 10 lines · jjluza
I try to make this modem working.
It works very well on kernel 2.4 series.
It work with some kernel 2.6 until test2-mm1.
But since test2-mm1, the newer kernel doesn't work anymore. There is 2 related drivers for this modem.
The one which is included in the kernel and which can be found here :
http://www.linux-usb.org/SpeedTouch/
and the one which I've always used until now :
speedtouch.sourceforge.net
Quoted 2 lines
when I notice that the old one doesn't work anymore, I try with the driver which included in the kernel, without success.
Take a look at a thread about this on the linux-usb-devel mailing list. People are working on narrowing down the patch that caused this problem and could probably use your help.
thanks,
greg k-h
Le Mercredi 20 Août 2003 02:34, vous avez écrit :
Quoted 14 lines · jjluza
Quoted 10 lines
I try to make this modem working.
It works very well on kernel 2.4 series.
It work with some kernel 2.6 until test2-mm1.
But since test2-mm1, the newer kernel doesn't work anymore. There is 2 related drivers for this modem.
The one which is included in the kernel and which can be found here :
http://www.linux-usb.org/SpeedTouch/
and the one which I've always used until now :
speedtouch.sourceforge.netQuoted 2 lines
when I notice that the old one doesn't work anymore, I try with the driver which included in the kernel, without success.
Quoted 7 lines
Take a look at a thread about this on the linux-usb-devel mailing list. People are working on narrowing down the patch that caused this problem and could probably use your help.
thanks,
greg k-h
ok, I find the mailing list you said
I find the thread too, but it seems that the problem they pointed has nothing to do with mine.
Anyway, I post a copy of my message on the user ml ;)
If you think I should post on the devel ml, I could post a copy on it too. thanks.
Quoted 3 lines · jjluza
ok, I find the mailing list you said
I find the thread too, but it seems that the problem they pointed has nothing to do with mine.
Why do you think that ? From your description, it's exactly the same:
the user-space speedtouch driver does not work after 2.6.0-test2
regards
john
Signature · 2 lines
Khendon's Law: If the same point is made twice by the same person, the thread is over.
Le Mercredi 20 Août 2003 03:38, vous avez écrit :
Quoted 10 lines · jjluza
Quoted 3 lines
ok, I find the mailing list you said
I find the thread too, but it seems that the problem they pointed has nothing to do with mine.Why do you think that ? From your description, it's exactly the same:
the user-space speedtouch driver does not work after 2.6.0-test2regards
john
hmm, it seems that my english is worse than I thought : I didn't understood what they said, the first time I read it.
Sorry, really
In fact, I haven't recognize the message error I got, but you're right, it seems to be the same problem.
So I hope my contribution will help the devels ;)
regards