Suspend to RAM problems

Hello,

I have got kernel 2.6.0-test5-mm1 on an Epox 8k9a9i Mainboard with KT400A and an Nvidia FX5200 using the nvidia-module and drivers. I use only onboard IDE and onboard ethernet.

I want to be able to use Suspend to RAM with my machine. I tried APM and ACPI, both with no success. I also tried with no X11.

1.) APM: (ACPI follows...)
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)

Sep 10 12:02:55 localhost apmd[441]: Suspending now
Sep 10 12:02:55 localhost kernel: hdc: start_power_step(step: 0)
Sep 10 12:02:55 localhost kernel: hdc: completing PM request, suspend
Sep 10 12:02:55 localhost kernel: hda: start_power_step(step: 0)
Sep 10 12:02:55 localhost kernel: hda: start_power_step(step: 1)
Sep 10 12:02:55 localhost kernel: hda: complete_power_step(step: 1, stat: 50, err: 0)
Sep 10 12:02:59 localhost kernel: hda: completing PM request, suspend
Sep 10 12:03:00 localhost kernel: hda: Wakeup request inited, waiting for !BSY...
Sep 10 12:03:00 localhost kernel: hda: start_power_step(step: 1000)
Sep 10 12:03:00 localhost kernel: blk: queue dfe03e00, I/O limit 4095Mb (mask 0xffffffff)
Sep 10 12:03:00 localhost kernel: hda: completing PM request, resume
Sep 10 12:03:00 localhost kernel: hdc: Wakeup request inited, waiting for !BSY...
Sep 10 12:03:00 localhost kernel: hdc: start_power_step(step: 1000)
Sep 10 12:03:00 localhost kernel: hdc: completing PM request, resume

I pressed the power button at the machines case, but it comes back to life straight away. I also tried with apm --verbose --suspend and --standby, but with no change.

2) ACPI
Thanks to Andrew de Quincey I can boot with ACPI without problems and I can read out my temp and so on, but when I do
echo -n "mem" >/sys/power/state
the machine goes into sleep (STR) but crashes after waking up again. And an
echo -n "S3" > /proc/acpi/sleep
doesn't work at all.
Also pressing the power button has NO effect. I think
it does not generate an event.

3) Questions
What can I do to get STR working straight?
Are these some stupid non-powersaving-aware drivers?
What makes my system wake up from apm suspend? How to debug? I can see the CPU temp with ACPI, but how do I see the case temp? Do I need to change things in the system BIOS or does linux ignore that?

Bye, claas

I also tried to suspend with ACPI in single user mode:

echo 3 >/proc/acpi/sleep

makes the system sleep within a second.

After waking it up by pressing a key or the power button the VGA Bios shows up for a second and afterwards I get this message:

APIC error on CPU0: 08(08)

...and it repeats endlessly :(

my keyboard is dead afterwards.

Hi!

Can you test on -test3 kernel?
Pavel

When do you have a heart between your knees?
[Johanka's followup: and *two* hearts?]

Ok, I will later today.

BTW: when I suspend from X11 with the nvidia-drivers, then the screen looks even worse :(

Hi!

Nvidia is binary only, right? I can't help with that.

Pavel

When do you have a heart between your knees?
[Johanka's followup: and *two* hearts?]

Unless he's using the opensource nv drivers that come with X?

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf

no, I can't, because I need Andrew De Quincey's linux-2.6.0-test4-acpi-picmode-5.patch to be able to boot acpi painless. :( But I could try with later test-kernels.

It's likely that if your system supports ACPI, the APM implementation will not work, especially if you boot with ACPI enabled.

What exactly does it do on wakeup?

Would you please try the patch at:

http://developer.osdl.org/~mochel/patches/test5-pm1/test5-pm2.diff.bz2

against 2.6.0-test5 and report whether or not it works?

Also, please try removing all modules before suspending and reinserting them after resuming.

Do you have any of the following enabled:

SMP?

Preempt?

APIC?

That should be:

	echo "3" > /proc/acpi/sleep

But, please use the sysfs interface.

Thanks,

Pat

Sure. That was with an APM-only enabled kernel.

When the system sleeps, it the power LED blinks. I call it wake-up when the system starts again. I press a key or the power button. Then the system beeps once and it comes back...

i will try it and report about my experiences later.

I did that. But I have a lot inside the kernel. I will try to modularise more.

no

no

yes:
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y

alright. but that has the same effects.

bye, claas

Mine crashes before suspending. It says something like:
Stoppings tasks
===========================================================
critical region / count pages [XXXXXXXXXXXX]

I'll give it a try too.

$ ls /proc/acpi
ac_adapter  battery  dsdt                 event  fan   power_resource  thermal_zone
alarm       button   embedded_controller  fadt   info  processor

It hangs the computer.

Pau

Hi!

This looks like swsusp, not S3.
Pavel

When do you have a heart between your knees?
[Johanka's followup: and *two* hearts?]

[...]
CC drivers/acpi/sleep/proc.o
drivers/acpi/sleep/proc.c: In function `acpi_system_write_sleep':
drivers/acpi/sleep/proc.c:72: error: void value not ignored as it ought to be
make[3]: *** [drivers/acpi/sleep/proc.o] Error 1 make[2]: *** [drivers/acpi/sleep] Error 2
make[1]: *** [drivers/acpi] Error 2
make: *** [drivers] Error 2

Is there an incremental patch from -pm1 to -pm2?
I would apply it to -test5-mm1 then

claas

Patch below. Sorry about that.

Pat

diff -Nru a/drivers/acpi/sleep/proc.c b/drivers/acpi/sleep/proc.c
@@ -69,7 +69,7 @@
 	state = simple_strtoul(str, NULL, 0);
 #ifdef CONFIG_SOFTWARE_SUSPEND
 	if (state == 4) {
-		error = software_suspend();
+		software_suspend();
 		goto Done;
 	}
 #endif

Also, no success. It's still the same.

I also tried with 2.4.22-ac2 with ACPI and also with APM. I was only able to APM suspend the machine. Everything else did not work :( I also tried without IO-APIC.

regards, claas

-------------------
some logs:
-------------------

# cat /proc/interupts
           CPU0       
  0:   13882622    IO-APIC-edge  timer
  1:       3569    IO-APIC-edge  i8042
  2:          0          XT-PIC  cascade
  8:          4    IO-APIC-edge  rtc
  9:          0    IO-APIC-edge  acpi
 12:      35791    IO-APIC-edge  i8042
 14:      78195    IO-APIC-edge  ide0
 15:         27    IO-APIC-edge  ide1
 16:    1043206   IO-APIC-level  nvidia
 21:         16   IO-APIC-level  ehci_hcd, uhci-hcd, uhci-hcd, uhci-hcd
 22:          0   IO-APIC-level  VIA8233
 23:     167984   IO-APIC-level  eth0
NMI:          0 
LOC:   13881222 
ERR:          0
MIS:          0

# lspci -v
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge (rev 80)
	Subsystem: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
	Flags: bus master, 66Mhz, medium devsel, latency 8
	Memory at d0000000 (32-bit, prefetchable) [size=128M]
	Capabilities: [80] AGP version 3.5
	Capabilities: [c0] Power Management version 2

00:01.0 PCI bridge: VIA Technologies, Inc.: Unknown device b198 (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e0000000-e1ffffff
Prefetchable memory behind bridge: d8000000-dfffffff
Capabilities: [80] Power Management version 2

00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])

	Subsystem: Unknown device 1695:3005
	Flags: bus master, medium devsel, latency 32, IRQ 21
	I/O ports at d000 [size=32]
	Capabilities: [80] Power Management version 2

00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])

	Subsystem: Unknown device 1695:3005
	Flags: bus master, medium devsel, latency 32, IRQ 21
	I/O ports at d400 [size=32]
	Capabilities: [80] Power Management version 2

00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])

	Subsystem: Unknown device 1695:3005
	Flags: bus master, medium devsel, latency 32, IRQ 21
	I/O ports at d800 [size=32]
	Capabilities: [80] Power Management version 2

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])

	Subsystem: Unknown device 1695:3005
	Flags: bus master, medium devsel, latency 32, IRQ 21
	Memory at e2000000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [80] Power Management version 2

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])

	Subsystem: Unknown device 1695:3005
	Flags: bus master, medium devsel, latency 32, IRQ 20
	I/O ports at dc00 [size=16]
	Capabilities: [c0] Power Management version 2

00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233 AC97 Audio Controller (rev 50)

	Subsystem: Unknown device 1695:3005
	Flags: medium devsel, IRQ 22
	I/O ports at e000 [size=256]
	Capabilities: [c0] Power Management version 2

00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74)

	Subsystem: Unknown device 1695:3005
	Flags: bus master, medium devsel, latency 32, IRQ 23
	I/O ports at e400 [size=256]
	Memory at e2001000 (32-bit, non-prefetchable) [size=256]
	Capabilities: [40] Power Management version 2

01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0322 (rev a1) (prog-if 00 [VGA])
Subsystem: ABIT Computer Corp.: Unknown device 8f15
Flags: bus master, 66Mhz, medium devsel, latency 248, IRQ 16
Memory at e0000000 (32-bit, non-prefetchable) [size=16M]
Memory at d8000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [44] AGP version 3.0

# dmesg

Linux version 2.6.0-test5-mm1 (root@zoo) (gcc version 3.3.2 20030831 (Debian prerelease)) #4 Fri Sep 12 00:01:52 CEST 2003 Video mode to be used for restore is ffff
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f5a10
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f1000 reserved twice.
hm, page 000f2000 reserved twice.
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 KT400A ) @ 0x000f7410
ACPI: RSDT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 KT400A AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7000
ACPI: DSDT (v001 KT400A AWRDACPI 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:8 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x1] trigger[0x1] lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0xe] global_irq[0xe] polarity[0x1] trigger[0x1])
ACPI: INT_SRC_OVR (bus[0] irq[0xf] global_irq[0xf] polarity[0x1] trigger[0x1])
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Building zonelist for node : 0
Kernel command line: root=/dev/hda1 devfs=mount
current: c04169c0
current->thread_info: c0474000
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes)
Detected 1533.329 MHz processor.
Console: colour VGA+ 80x25
Memory: 514172k/524224k available (2715k kernel code, 9304k reserved, 819k data, 352k init, 0k highmem) zapping low mappings.
Calibrating delay loop... 3022.84 BogoMIPS
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
-> /dev
-> /dev/console
-> /root

CPU:     After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU:     After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU:     After all inits, caps: 0383fbff c1c3fbff 00000000 00000020

Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Athlon(tm) XP 1800+ stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000

.......    : physical APIC id: 02
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 00178003
.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0003
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 001 01  0    0    0   0   0    1    1    71
 0a 001 01  0    0    0   0   0    1    1    79
 0b 001 01  0    0    0   0   0    1    1    81
 0c 001 01  0    0    0   0   0    1    1    89
 0d 001 01  0    0    0   0   0    1    1    91
 0e 001 01  0    0    0   0   0    1    1    99
 0f 001 01  0    0    0   0   0    1    1    A1
 10 000 00  1    0    0   0   0    0    0    00
 11 000 00  1    0    0   0   0    0    0    00
 12 000 00  1    0    0   0   0    0    0    00
 13 000 00  1    0    0   0   0    0    0    00
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00

IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1532.0959 MHz.
..... host bus clock speed is 266.0601 MHz.
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfb370, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20030813
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20)
ACPI: PCI Interrupt Link [ALKB] (IRQs 21)
ACPI: PCI Interrupt Link [ALKC] (IRQs 22)
ACPI: PCI Interrupt Link [ALKD] (IRQs 23)
Linux Plug and Play Support v0.97 (c) Adam Belay
SCSI subsystem initialized
drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1) 00:00:08[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1) 00:00:08[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1) 00:00:08[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1) 00:00:08[D] -> 2-19 -> IRQ 19
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
_CRS returns NULL! Using IRQ 21 for device (PCI Interrupt Link [ALKB]).
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
IOAPIC[0]: Set PCI routing entry (2-21 -> 0xc9 -> IRQ 21 Mode:1 Active:1) 00:00:10[A] -> 2-21 -> IRQ 21
Pin 2-21 already programmed
Pin 2-21 already programmed
Pin 2-21 already programmed
_CRS returns NULL! Using IRQ 20 for device (PCI Interrupt Link [ALKA]).
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
IOAPIC[0]: Set PCI routing entry (2-20 -> 0xd1 -> IRQ 20 Mode:1 Active:1) 00:00:11[A] -> 2-20 -> IRQ 20
Pin 2-21 already programmed
_CRS returns NULL! Using IRQ 22 for device (PCI Interrupt Link [ALKC]).
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
IOAPIC[0]: Set PCI routing entry (2-22 -> 0xd9 -> IRQ 22 Mode:1 Active:1) 00:00:11[C] -> 2-22 -> IRQ 22
_CRS returns NULL! Using IRQ 23 for device (PCI Interrupt Link [ALKD]).
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xe1 -> IRQ 23 Mode:1 Active:1) 00:00:11[D] -> 2-23 -> IRQ 23
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-23 already programmed
Pin 2-23 already programmed
Pin 2-23 already programmed
Pin 2-23 already programmed
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
ikconfig 0.6 with /proc/config*
devfs: v1.22 (20021013) Richard Gooch ([email protected])
devfs: boot_options: 0x1
udf: registering filesystem
SGI XFS for Linux with no debug enabled
Initializing Cryptographic API
PCI: Via IRQ fixup for 0000:00:10.0, from 11 to 5
PCI: Via IRQ fixup for 0000:00:10.1, from 11 to 5
PCI: Via IRQ fixup for 0000:00:10.2, from 10 to 5
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Thermal Zone [THRM] (26 C)
request_module: failed /sbin/modprobe -- parport_lowlevel. error = -16
lp: driver loaded but no devices found
Real Time Clock Driver v1.12
Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
lp0: using parport0 (polling).
Using anticipatory scheduling io scheduler
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
via-rhine.c:v1.10-LK1.1.19-2.5 July-12-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6102 Rhine-II at 0xe2001000, 00:04:61:46:e7:38, IRQ 23.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 41e1. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1

    ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:pio

hda: ST3120023A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: TOSHIBA DVD-ROM SD-R5112, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2
hdc: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: irq 21, pci mem e080f000
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-13
hub 1-0:0: USB hub found
hub 1-0:0: 6 ports detected
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
uhci-hcd 0000:00:10.0: UHCI Host Controller
uhci-hcd 0000:00:10.0: irq 21, io base 0000d000
uhci-hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
hub 2-0:0: USB hub found
hub 2-0:0: 2 ports detected
uhci-hcd 0000:00:10.1: UHCI Host Controller
uhci-hcd 0000:00:10.1: irq 21, io base 0000d400
uhci-hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
hub 3-0:0: USB hub found
hub 3-0:0: 2 ports detected
uhci-hcd 0000:00:10.2: UHCI Host Controller
uhci-hcd 0000:00:10.2: irq 21, io base 0000d800
uhci-hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
hub 4-0:0: USB hub found
hub 4-0:0: 2 ports detected
drivers/usb/core/usb.c: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
drivers/usb/core/usb.c: registered new driver usb-storage
USB Mass Storage support registered.
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: PC Speaker
input: PS2++ Logitech Wheel Mouse on isa0060/serio1
serio: i8042 AUX port at 0x60,0x64 irq 12
input: AT Set 2 keyboard on isa0060/serio0
serio: i8042 KBD port at 0x60,0x64 irq 1
Advanced Linux Sound Architecture Driver Version 0.9.6 (Wed Aug 20 20:27:13 2003 UTC).
request_module: failed /sbin/modprobe -- snd-card-0. error = -16
PCI: Setting latency timer of device 0000:00:11.5 to 64
hub 1-0:0: debounce: port 3: delay 100ms stable 4 status 0x501
hub 3-0:0: debounce: port 1: delay 100ms stable 4 status 0x101
hub 3-0:0: new USB device on port 1, assigned address 2
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0317 ALSA device list:
#0: VIA 8235 at 0xe000, irq 22
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
BIOS EDD facility v0.09 2003-Jan-22, 1 devices found
PM: Reading swsusp image.
PM: Resume from disk failed.
ACPI: (supports S0 S3 S4 S5)
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 352k freed
EXT3 FS on hda1, internal journal
nvidia: module license 'NVIDIA' taints kernel.
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4496 Wed Jul 16 19:03:09 PDT 2003 kjournald starting. Commit interval 5 seconds
EXT3 FS on hda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: Setting full-duplex based on MII #1 link partner capability of 41e1.

Hi again,

or do I need to setup something particular in my system BIOS?

Claas