Patch to get cpqphp working with IOAPIC (2.6.0-test5)
Hi,
Here is a patch for 2.6.0-test5 to get cpqphp working with IOAPIC. My earlier statement that a kernel patch is not needed for 2.6 is true only when ACPI is enabled. A similar patch is needed in pcibios_enable_irq() for 2.4 kernel and I will send it out later.
The fix is in pirq_enable_irq(). This function is called indirectly by pci_enable_device(). For device present during boot up, it should get the proper dev->irq for pcibios_fixup_irqs() has been called to get the dev->irq from MP table. If the value is still zero, then this is properly caused by "buggy MP table". For hot-plug device, its dev->irq is 0 when the pci_enable_device() is called for it hasn't gone through the fixup. Therefore, the code (similiar to the code in pcibios_fixup_irqs) is needed here.
Thanks,
Dely
arch/i386/pci/irq.c +30 -3
@@ -812,9 +812,36 @@pci_read_config_byte (dev,PCI_INTERRUPT_PIN , &pin);if (pin && !pcibios_lookup_irq (dev,1 ) && !dev->irq) {char *msg; -if (io_apic_assign_pci_irqs) - msg =" Probably buggy MP table." ; -else if (pci_probe &PCI_BIOS_IRQ_SCAN ) +if (io_apic_assign_pci_irqs) { +int irq; + + pin--;/* interrupt pins are numbered starting from 1 */ + irq =IO_APIC_get_PCI_irq_vector (dev->bus->number,PCI_SLOT (dev->devfn), pin); +/* +* Busses behind bridges are typically not listed in the MP-table. +* In this case we have to look up the IRQ based on the parent bus, +* parent slot, and pin number. The SMP code detects such bridged +* busses itself so we should get into this branch reliably. +*/ +if (irq <0 && dev->bus->parent) {/* go back to the bridge */ +struct pci_dev * bridge = dev->bus->self; + + pin = (pin +PCI_SLOT (dev->devfn)) %4 ; + irq =IO_APIC_get_PCI_irq_vector (bridge->bus->number, +PCI_SLOT (bridge->devfn), pin); +if (irq >=0 ) { +printk (KERN_WARNING "PCI: using PPB(B%d,I%d,P%d) to get irq %d\n" , + bridge->bus->number,PCI_SLOT (bridge->devfn), pin, irq); + } + } +if (irq >=0 ) { +printk (KERN_INFO "PCI->APIC IRQ transform: (B%d,I%d,P%d) -> %d\n" , + dev->bus->number,PCI_SLOT (dev->devfn), pin, irq); + dev->irq = irq; +return 0 ; + }else + msg =" Probably buggy MP table." ; + }else if (pci_probe &PCI_BIOS_IRQ_SCAN ) msg ="" ;else msg =" Please try using pci=biosirq." ;
drivers/pci/hotplug/cpqphp_ctrl.c +3 -1
@@ -2446,7 +2446,7 @@ u8 behind_bridge, struct resource_lists * resources) { int cloop; -u8 IRQ ; +u8 IRQ =0 ;u8 temp_byte;u8 device;u8 class_code;
@@ -3021,6 +3021,7 @@ } }// End of base register loop +#if !defined(CONFIG_X86_IO_APIC )// Figure out which interrupt pin this function uses rc =pci_bus_read_config_byte (pci_bus, devfn,PCI_INTERRUPT_PIN , &temp_byte);
@@ -3045,6 +3046,7 @@// IRQ Line rc =pci_bus_write_config_byte (pci_bus, devfn,PCI_INTERRUPT_LINE ,IRQ ); +#endif if (!behind_bridge) { rc =cpqhp_set_irq (func->bus, func->device, temp_byte +0x09 ,IRQ );
drivers/pci/hotplug/cpqphp_pci.c +2 -0
@@ -151,6 +151,7 @@*/ int cpqhp_set_irq (u8 bus_num,u8 dev_num,u8 int_pin,u8 irq_num) { +#if !defined(CONFIG_X86_IO_APIC )int rc;u16 temp_word;struct pci_dev fakedev;
@@ -175,6 +176,7 @@// This should only be for x86 as it sets the Edge Level Control Register outb ((u8) (temp_word &0xFF ),0x4d0 );outb ((u8) ((temp_word &0xFF00 ) >>8 ),0x4d1 ); +#endif return 0 ; }
Quoted 8 lines · Dely Sy
Hi,
Here is a patch for 2.6.0-test5 to get cpqphp working with IOAPIC. My earlier statement that a kernel patch is not needed for 2.6 is true only when ACPI is enabled. A similar patch is needed in
pcibios_enable_irq()for 2.4 kernel and I will send it out later.
Quoted 8 lines
The fix is in
pirq_enable_irq(). This function is called indirectly bypci_enable_device(). For device present during boot up, it should get the properdev->irqforpcibios_fixup_irqs()has been called to get thedev->irqfrom MP table. If the value is still zero, then this is properly caused by "buggy MP table". For hot-plug device, itsdev->irqis 0 when thepci_enable_device()is called for it hasn't gone through the fixup. Therefore, the code (similiar to the code inpcibios_fixup_irqs) is needed here.
Wow, very sorry for the long delay here. I took the patch you sent me for the irq.c file in your previous big SHPC patch and added it to the rest of the cpqphp changes you made here, and applied it to my trees.
thanks,
greg k-h