DAC960: Bad Data Block Found
If there's some place better to post this, please let me know. Since the DAC960 driver has been orphaned, I haven't heard of anyone stepping up to take it over, so I don't know where to go for help other than linux-kernel.
Basically, the problem here is that I've got a mission-critical box running on this controller and I'm starting to get some odd errors. The controller and disks are about 3 years old, so I'm thinking this might be an EOL issue but I'm hoping, of course, that that's not the case. I see in my kernel msgs:
DAC960#0: Error Condition MEDIUM ERROR on READ:
DAC960#0: /dev/rd/c0d0: absolute blocks 405095..405102
DAC960#0: /dev/rd/c0d0p1: relative blocks 405032..405039
DAC960#0: Error Condition MEDIUM ERROR on READ:
DAC960#0: /dev/rd/c0d0: absolute blocks 405095..405102
DAC960#0: /dev/rd/c0d0p1: relative blocks 405032..405039
DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found
Sounds bad, but the drives are still ticking and I haven't noticed any fs corruption. How serious is the error? Can it be ignored? Is it time to move to another array? Would dropping everything, scrubbing, and restoring be sufficient?
Thanks,
John
More info:
Kernel: 2.4.21, stock build
Controller: Mylex 160LP, 16MB
# cat /proc/rd/c0/initial_status ***** DAC960 RAID Driver Version 2.4.11 of 11 October 2001 ***** Copyright 1998-2001 by Leonard N. Zubkoff <[email protected]> Configuring Mylex AcceleRAID 160 PCI RAID Controller Firmware Version: 6.00-03, Channels: 1, Memory Size: 16MB PCI Bus: 0, Device: 11, Function: 1, I/O Address: Unassigned PCI Address: 0xDD000000 mapped at 0xE0800000, IRQ Channel: 16 Controller Queue Depth: 512, Maximum Blocks per Command: 2048 Driver Queue Depth: 511, Scatter/Gather Limit: 128 of 257 Segments Physical Devices: 0:0 Vendor: HP Model: 18.2GB C 80-S60R Revision: S60R Wide Synchronous at 80 MB/sec Serial Number: TEL49262 Disk Status: Online, 35532800 blocks 0:1 Vendor: HP Model: 18.2GB C 80-S60R Revision: S60R Wide Synchronous at 80 MB/sec Serial Number: TEL34793 Disk Status: Online, 35532800 blocks 0:2 Vendor: IBM Model: DDYS-T18350M Revision: S94N Wide Synchronous at 160 MB/sec Serial Number: TEFX1786 Disk Status: Online, 35807232 blocks 0:3 Vendor: HP Model: 18.2GB C 80-S60R Revision: S60R Wide Synchronous at 80 MB/sec Serial Number: TEL34013 Disk Status: Online, 35532800 blocks 0:4 Vendor: IBM Model: DDYS-T18350M Revision: S94N Wide Synchronous at 160 MB/sec Serial Number: 4EFTK069 Disk Status: Online, 35807232 blocks 0:7 Vendor: MYLEX Model: AcceleRAID 160 Revision: 0600 Wide Synchronous at 160 MB/sec Serial Number: Logical Drives: /dev/rd/c0d0: RAID-5, Online, 142082048 blocks Logical Device Initialized, BIOS Geometry: 255/63 Stripe Size: 64KB, Segment Size: 8KB Read Cache Disabled, Write Cache Enabled
Signature · 4 lines
# John Madden [email protected] # MailandFiles.com: Your mail, your files: http://www.mailandfiles.com # FreeLists: Free mailing lists for all: http://www.freelists.org # Linux, Apache, Perl and C: All the best things in life are free!
On Monday 22 September 2003 02:30, John Madden wrote:
Hi John,
Quoted 4 lines
If there's some place better to post this, please let me know. Since the DAC960 driver has been orphaned, I haven't heard of anyone stepping up to take it over, so I don't know where to go for help other than linux-kernel.
well, take a look at: http://www.osdl.org/archive/dmo/DAC960/
I use that driver for some months now w/o any problems at all where 2.4.11 driver version has some problems. I use these controllers:
- Mylex DAC1164P PCI RAID Controller, 64MB cache
- Mylex DAC960PTL1 PCI RAID Controller, 8MB cache
Quoted 5 lines
DAC960#0: Error Condition MEDIUM ERROR on READ:
DAC960#0:/dev/rd/c0d0: absolute blocks 405095..405102
DAC960#0:/dev/rd/c0d0p1: relative blocks 405032..405039
DAC960#0: Error Condition MEDIUM ERROR on READ:
DAC960#0:/dev/rd/c0d0: absolute blocks 405095..405102
Quoted 8 lines
DAC960#0:
/dev/rd/c0d0p1: relative blocks 405032..405039
DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found Sounds bad, but the drives are still ticking and I haven't noticed any fs corruption. How serious is the error? Can it be ignored? Is it time to move to another array? Would dropping everything, scrubbing, and restoring be sufficient?
hmm, never saw those messages. Already fsck -f'ed? Anyway, those messages would scare me :)
ciao, Marc
Quoted 6 lines · John Madden
DAC960#0: Error Condition MEDIUM ERROR on READ:
DAC960#0:/dev/rd/c0d0: absolute blocks 405095..405102
DAC960#0:/dev/rd/c0d0p1: relative blocks 405032..405039
DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found DAC960#0: Logical Drive 0 (/dev/rd/c0d0) Bad Data Block Found
Your controller seems to be logging disk errors. I guess run whatever diagnostics the controller manual recommends and replace any dud drives