TWEAK/PATCH for 2.4.22: Fixing yenta with ToPIC95 on resume from swsusp

PCMCIA in a Toshiba libretto L2 failed to work on resume from swsusp/S4. Modules were unloaded on suspend and reloaded on resume.

Firstly, the controller ends up being disabled and secondly shared interrupts break.

This is an applicable chipset.

00:12.0 CardBus bridge: Toshiba America Info Systems ToPIC95 PCI to Cardbus Bridge with ZV Support (rev 32)

        Subsystem: Toshiba America Info Systems: Unknown device 0001
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR-
        Latency: 168
        Interrupt: pin A routed to IRQ 3
        Region 0: Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        Memory window 0: 10400000-107ff000
        Memory window 1: 10800000-10bff000
        I/O window 0: 00004000-000040ff
        I/O window 1: 00004400-000044ff
        BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt- PostWrite-
        16-bit legacy interface ports at 0001

To reenable the controller on resume:

# pcitweak -w 00:12:0 0x84 -b 0

It also had trouble with shared interrupts on resume.

Applicable chipset:

0:07.0 ISA bridge: ALi Corporation M1533 PCI to ISA Bridge [Aladdin IV]
Subsystem: Toshiba America Info Systems: Unknown device 0004
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [a0] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 Bridge: ALi Corporation M7101 PMU
Subsystem: Toshiba America Info Systems: Unknown device 0001
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-

The patch below fixes that by preventing interrupt sharing but may break things, so use it only when it does not work and with interrupts being shared.

@@ -517,7 +517,7 @@
                        acpi_device_bid(link->device));
                return_VALUE(-ENODEV);
        } else {
-               acpi_irq_penalty[link->irq.active] += 100;
+               acpi_irq_penalty[link->irq.active] += 1000000;
                printk(PREFIX "%s [%s] enabled at IRQ %d\n",
                        acpi_device_name(link->device),
                        acpi_device_bid(link->device), link->irq.active);

With the tweaks presented, this machine is fully functional on resume from swsusp/S4 including PCMCIA, USB and network using swsusp-1.1-rc9 on 2.4.22.

Regards
Michael

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
_______________________________________________
swsusp-devel mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/swsusp-devel

-------------------------------------------------------

-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf