Skip to contentSkip to conversation

ENS1371 joystick problem, bug in driver?

DISCUSSION Juan Linietsky 3 participants 3 messages Oct 11, 2003 – Oct 13, 2003

lore
Share & tools
lore
#0 lore raw

I cant seem to get the joystick port to run under this card (Ensoniq 1371) under alsa 0.9.rc6.

jstest on /dev/js0 (and others) returns no such device.

However it seems to work fine on the OSS/Free driver 'es1371.o' with parameter 'joystick=1'

Relevant sections to /etc/asound.state:

state.AudioPCI {
        control.1 {
                comment.access 'read write'
                comment.type BOOLEAN
                iface CARD
                name 'Joystick Enable'
                value true
        }
        control.2 {
                comment.access 'read write'
                comment.type ENUMERATED
                comment.item.0 'port 0x200'
                comment.item.1 'port 0x208'
                comment.item.2 'port 0x210'
                iface CARD
                name 'Joystick Address'
                value 'port 0x200'
        }

I tried using all the values above, but nothing works, and higher values are ignored (error is reported).

However, when using the OSS/Free driver, by doing cat /proc/ioports shows the follownig

0218-021f : es1371

I can however, as mentioned above, not set such value on /etc/asound.state.

Regards

Juan Linietsky.

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php

#1 lore raw
Quoted 2 lines · Juan Linietsky

I cant seem to get the joystick port to run under this card (Ensoniq 1371) under alsa 0.9.rc6.

You might have better luck with 0.9.7c.

Quoted 19 lines
state.AudioPCI {
        control.1 {
                comment.access 'read write'
                comment.type BOOLEAN
                iface CARD
                name 'Joystick Enable'
                value true
        }
        control.2 {
                comment.access 'read write'
                comment.type ENUMERATED
                comment.item.0 'port 0x200'
                comment.item.1 'port 0x208'
                comment.item.2 'port 0x210'
                iface CARD
                name 'Joystick Address'
                value 'port 0x200'
        }
Quoted 2 lines

I tried using all the values above, but nothing works, and higher values are ignored (error is reported).

The driver cannot change the gameport's port address while it's enabled, so you have to disable the joystick, then change the port, then enable it again.

HTH
Clemens

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php

#2 lore raw

At Mon, 13 Oct 2003 14:28:04 +0200 (METDST),

Quoted 26 lines · Clemens Ladisch
Quoted 2 lines · Juan Linietsky

I cant seem to get the joystick port to run under this card (Ensoniq 1371) under alsa 0.9.rc6.

You might have better luck with 0.9.7c.

Quoted 19 lines
state.AudioPCI {
        control.1 {
                comment.access 'read write'
                comment.type BOOLEAN
                iface CARD
                name 'Joystick Enable'
                value true
        }
        control.2 {
                comment.access 'read write'
                comment.type ENUMERATED
                comment.item.0 'port 0x200'
                comment.item.1 'port 0x208'
                comment.item.2 'port 0x210'
                iface CARD
                name 'Joystick Address'
                value 'port 0x200'
        }
Quoted 6 lines
Quoted 2 lines

I tried using all the values above, but nothing works, and higher values are ignored (error is reported).

The driver cannot change the gameport's port address while it's enabled, so you have to disable the joystick, then change the port, then enable it again.

i'm working on taking the joystick stuffs back to the module parameters again. will be finished in a couple of days. keep tuned.

Takashi

-------------------------------------------------------
This SF.net email is sponsored by: SF.net Giveback Program. SourceForge.net hosts over 70,000 Open Source Projects. See the people who have HELPED US provide better services:
Click here: http://sourceforge.net/supporters.php