start_threshold having no effect
Hi,
I am trying to build an application using ALSA, and which requires low playback delays.
My first idea was to have a small hardware buffer to limit the playout delays. But then if for some reason the buffer gets full, the card stops, and the next writei will block for about one second.
My second idea was to have a rather big hw buffer (500ms), and then set the start_threshold to a low value (32 frames for instance). But whatever my parameters were, I always got a playout delay of about the hw buffer size.
I think the best way is the second one, but I can't figure out what I did wrong. Here are the parameters I'm using:
20/10 18:56 /proc/asound/card0/pcm0p/sub0% cat hw_params
access: RW_INTERLEAVED
format: S16_LE
subformat: STD
channels: 1
rate: 8000 (8000/1)period_size: 32buffer_size: 4000tick_time: 1000
20/10 19:12 /proc/asound/card0/pcm0p/sub0% cat sw_paramststamp_mode: NONEperiod_step: 1sleep_min: 0avail_min: 16xfer_align: 32start_threshold: 32stop_threshold: 4000silence_threshold: 0silence_size: 0
boundary: 2097152000
I am using a 2.6.0-test3 kernel (preemptive) with the 0.9.6 libasound. My soundcard is a USB Plantronics Headset. The card is open both in PLAYBACK and CAPTURE mode.
Thanks,
Signature · 8 lines
Jobi ------------------------------------------------------- This SF.net email is sponsored by OSDN developer relations Here's your chance to show off your extensive product knowledge We want to know what you know. Tell us and you have a chance to win $100 http://www.zoomerang.com/survey.zgi?HRPT1X3RYQNC5V4MLNSV3E54
Quoted 4 lines
My second idea was to have a rather big hw buffer (500ms), and then set the
start_thresholdto a low value (32 frames for instance). But whatever my parameters were, I always got a playout delay of about the hw buffer size.
the output latency is always roughly the size of the hardware buffer. there is no way to avoid this. the best you could ever do would be one period, where there are two periods per buffer (i.e half the buffer size). when i say "the best you could do", the truth is that you probably can't do it. the very first sample you deliver to the hardware will have a delay of 1 period, each subsequent sample has a steadily increasing delay all the way up to the last sample, which is delayed by the length of the entire hardware buffer (2 periods). this assumes that delivery is basically instaneous:
obviously, if you take time to deliver it, the delay drops, but the total delay (from when you could have written to when the sound is audible) is the same.
i don't know what you're doing, but you might to investigate JACK, which does precisely what you're hoping for, supports the lowest latencies of any supported hardware (with an appropriate kernel), but also bundles it all up in an easy to use API. jackit.sf.net. if nothing else, you can study JACK's ALSA code to see how it does it. its not simple.
--p
-------------------------------------------------------
This SF.net email is sponsored by OSDN developer relations Here's your chance to show off your extensive product knowledge We want to know what you know. Tell us and you have a chance to win $100
http://www.zoomerang.com/survey.zgi?HRPT1X3RYQNC5V4MLNSV3E54
Quoted 4 lines · Paul Davis
the output latency is always roughly the size of the hardware buffer. there is no way to avoid this. the best you could ever do would be one period, where there are two periods per buffer (i.e half the buffer size). when i say "the best you could do", the truth is
Quoted 8 lines
that you probably can't do it. the very first sample you deliver to the hardware will have a delay of 1 period, each subsequent sample has a steadily increasing delay all the way up to the last sample, which is delayed by the length of the entire hardware buffer (2 periods). this assumes that delivery is basically instaneous:
obviously, if you take time to deliver it, the delay drops, but the total delay (from when you could have written to when the sound is audible) is the same.
I am working on a voice over IP application. We would like delays from the write to soundcard to the actual playout lower than 50ms. Do you think it is impossible with ALSA ? With OSS free the delay we got were quite good, without any tweaking. But ALSA is said to have better support for full-duplex.
Maybe using a small buffer on the sound card should then be a better solution ? I tried with a buffer of 50 ms, and the playout is fine until for some reason the buffer gets full. At that point I get an EPIPE error on the next write, I then do a snd_pcm_prepare, can write again, but after that both reading and writing give a lot of errors, and after a very short while a write will block for more than one second. Are those ALSA related problems, or hardware ones ?
Thanks,
Signature · 9 lines
Jobi Please excuse me for the dupplicate previous e-mail ------------------------------------------------------- This SF.net email is sponsored by OSDN developer relations Here's your chance to show off your extensive product knowledge We want to know what you know. Tell us and you have a chance to win $100 http://www.zoomerang.com/survey.zgi?HRPT1X3RYQNC5V4MLNSV3E54
Quoted 14 lines · Johan Bilien
Quoted 4 lines · Paul Davis
the output latency is always roughly the size of the hardware buffer. there is no way to avoid this. the best you could ever do would be one period, where there are two periods per buffer (i.e half the buffer size). when i say "the best you could do", the truth is
Quoted 8 lines
that you probably can't do it. the very first sample you deliver to the hardware will have a delay of 1 period, each subsequent sample has a steadily increasing delay all the way up to the last sample, which is delayed by the length of the entire hardware buffer (2 periods). this assumes that delivery is basically instaneous:
obviously, if you take time to deliver it, the delay drops, but the total delay (from when you could have written to when the sound is audible) is the same.
Quoted 5 lines
I am working on a voice over IP application. We would like delays from the write to soundcard to the actual playout lower than 50ms. Do you think it is impossible with ALSA ? With OSS free the delay we got were quite good, without any tweaking. But ALSA is said to have better support for full-duplex.
Comparing to OSS: OSS does not have any xrun detection (overrun/underrun).
Quoted 3 lines
Maybe using a small buffer on the sound card should then be a better solution ? I tried with a buffer of 50 ms, and the playout is fine until for some reason the buffer gets full. At that point I get an EPIPE error
If you get EPIPE error, then the buffer is empty and you've reached an underrun.
Quoted 2 lines
on the next write, I then do a
snd_pcm_prepare, can write again, but after that both reading and writing give a lot of errors, and after a
Sure. You need to resync here for full duplex. At this point, you have much more data captured than played, so you need to flush also the capture buffer.
Quoted 2 lines
very short while a write will block for more than one second. Are those ALSA related problems, or hardware ones ?
You said that you're using an USB device. It might be a problem with our USB driver. Also, USB devices are working with 1ms periods at the physical level, so transferring 32 frames does not make probably sense anyway.
For a voice IP applications, it probably make sense to work without over and underrun detection (yes, if CPU is busy, there will be some scratches, but you'll avoid resyncing). Simply set stop_threshold to boundary for the no-xrun detection.
Jaroslav
-----
Jaroslav Kysela <[email protected]>
Linux Kernel Sound Maintainer
ALSA Project, SuSE Labs
-------------------------------------------------------
This SF.net email is sponsored by OSDN developer relations Here's your chance to show off your extensive product knowledge We want to know what you know. Tell us and you have a chance to win $100
http://www.zoomerang.com/survey.zgi?HRPT1X3RYQNC5V4MLNSV3E54
At Tue, 21 Oct 2003 13:32:10 +0200 (CEST),
Quoted 7 lines · Jaroslav
Quoted 3 lines
very short while a write will block for more than one second. Are those ALSA related problems, or hardware ones ?
You said that you're using an USB device. It might be a problem with our USB driver. Also, USB devices are working with 1ms periods at the physical level, so transferring 32 frames does not make probably sense anyway.
this should be ok, since the sample rate is 8k Hz (although RT-scheduling would be needed for 4ms periods.)
but 1ms period alignment is important: if you want a RT process with the USB audio device, choose the sample rate with multiple of 1000. for example, avoid 44.1kHz, but use 48k instead.
Takashi
-------------------------------------------------------
This SF.net email is sponsored by OSDN developer relations Here's your chance to show off your extensive product knowledge We want to know what you know. Tell us and you have a chance to win $100
http://www.zoomerang.com/survey.zgi?HRPT1X3RYQNC5V4MLNSV3E54
Quoted 4 lines · Jaroslav Kysela
For a voice IP applications, it probably make sense to work without over and underrun detection (yes, if CPU is busy, there will be some scratches, but you'll avoid resyncing). Simply set
stop_thresholdto boundary for the no-xrun detection.
Thanks a lot, I did this and was then able to run the application with delays of about 10 ms.
Signature · 8 lines
Jobi ------------------------------------------------------- This SF.net email is sponsored by OSDN developer relations Here's your chance to show off your extensive product knowledge We want to know what you know. Tell us and you have a chance to win $100 http://www.zoomerang.com/survey.zgi?HRPT1X3RYQNC5V4MLNSV3E54
Quoted 5 lines
I am working on a voice over IP application. We would like delays from the write to soundcard to the actual playout lower than 50ms. Do you think it is impossible with ALSA ? With OSS free the delay we got were quite good, without any tweaking. But ALSA is said to have better support for full-duplex.
JACK routinely works with 5ms latency on low latency kernels, and 20ms on regular kernels. its easy, as long as you understand how to write software correctly.
Quoted 7 lines
Maybe using a small buffer on the sound card should then be a better solution ? I tried with a buffer of 50 ms, and the playout is fine until for some reason the buffer gets full. At that point I get an EPIPE error on the next write, I then do a
snd_pcm_prepare, can write again, but after that both reading and writing give a lot of errors, and after a very short while a write will block for more than one second. Are those ALSA related problems, or hardware ones ?
OSS has *NO* xrun detection. ALSA has it, and its turned on by default. you need to set the stop threshold to -1, so that ALSA never stops for xruns and never reports them.
But please note: if you get EPIPE, it means there was an xrun, which in turn means that your application was *not keeping up with the audio interface*. you will normally never know this under OSS, whereas ALSA offers you the chance to find out.
-------------------------------------------------------
This SF.net email is sponsored by OSDN developer relations Here's your chance to show off your extensive product knowledge We want to know what you know. Tell us and you have a chance to win $100
http://www.zoomerang.com/survey.zgi?HRPT1X3RYQNC5V4MLNSV3E54