2.6.0-test9 breaks cdrecord w. ide-scsi device
Just rebooted my long-running machine and now strongly suspect that it is a kernel bug:
I try to burn (dummy mode) 20 tracks of audio on a 'PIONEER DVD-RW DVR-106D' drive.
At -test8 it would work (tested 4 times now, several with even older kernels). On -test 9 I always (> 15 times tested) get the messages quoted. The drive is on ide-scsi [M], sg is built-in, sr is a module. Ask me anything else you may want me to try..
cdrecord 2.01.xx :
Track 01: 31 of 38 MB written (fifo 100%) [buf 90%] 19.8x.cdrecord:
Input/output error. write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 36 F3 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 D3 10 FA 0E 26 01 30 FE 08 01 00 00 Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x01 (logical unit communication time-out) Fru 0x0 Sense flags: Blk 13832442 (not valid)
cmd finished after 2.004s timeout 200s
write track data: error after 33085584 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
Writing time: 28.974s
Average write speed 154.5x.
Min drive buffer fill was 79%
Fixating...
cdrecord 1.10:
Track 04: 1 of 33 MB written (fifo 98%).cdrecord.old: Input/output error.
write_g1: scsi sendcmd: no error CDB: 2A 00 00 00 BE 9D 00 00 1B 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 D3 10 FA 0E 26 01 30 FE 08 01 00 00 Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x01 (logical unit communication time-out) Fru 0x0 Sense flags: Blk 13832442 (not valid)
cmd finished after 2.004s timeout 200s
write track data: error after 1460592 bytes
Sense Bytes: 70 00 00 00 00 00 00 0E 00 00 00 00 00 00 00 00 00 00
Writing time: 57.892s
Fixating...
A message that is not in the archive (sent off-list or not yet received): [email protected]
Quoted 15 lines
Hello
I don't really know what the problem with ide-scsi is (I'm not much of a programmer) but is there any particular reason you're clinging to the old ide-scsi method for CD writing? This has been broken a few times now in the 2.5/2.6 tree. Even when it is working, it's still somewhat broken and they know it. I have found that the maximum speed I can get is 16x using ide-scsi in the 2.6 tree.
There is now ide-cd writing support, and cdrecord 2 supports it. I build that stuff modular, so I just load the ide-cd and isofs modules (modprobe takes care of the rest). I achieve the fastest writing speeds I've ever had, using this driver. Far better than ide-scsi or even Sleazy CD Creator in Windows.
Quoted 8 lines
In the cdrecord command, everything is the same except you use dev=/dev/hdxx instead of the dev=x,x,x scsi target notation. For example:
cdrecord -v speed=48 dev=/dev/hdd -data filename.iso
Just in case you didn't know this or have never tried this. I hope it helps you.
It's true that I hadn't tried the native ATAPI method lately.
My point, however, was that there is a regression from -test8 to -test9 about cdrecord-ing.
Quoted 11 lines
Hello
...
There is now ide-cd writing support, and cdrecord 2 supports it. I build that stuff modular, so I just load the ide-cd and isofs modules (modprobe takes care of the rest). I achieve the fastest writing speeds I've ever had, using this driver. Far better than ide-scsi or even Sleazy CD Creator in Windows.
...
Tried it. Now used /dev/hdd there..
This time it worked a few times and some other times it failed. It now seems that I got a buffer underrun, although I do have 'realtime priority' for the process.
Note that I'm not using 'burnfree'. That's why I have linux anyway :) .
Can anybody examine why is the buffer of cdrecord less than 100% with RR-scheduling? That would never happen in 2.4, cdrecord 1.10 ..
Track 10: 25 of 32 MB written (fifo 25%) [buf 94%] 15.8x.cdrecord: Success. write_g1: scsi sendcmd: no error CDB: 2A 00 00 02 3C 76 00 00 1B 00 status: 0x2 (CHECK CONDITION) Sense Bytes: F1 00 05 00 32 35 73 0E 00 00 00 00 21 02 00 00 Sense Key: 0x5 Illegal Request, deferred error, Segment 0 Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0 Sense flags: Blk 3290483 (valid) resid: 63504
cmd finished after 0.006s timeout 200s
write track data: error after 27179712 bytes
cdrecord: The current problem looks like a buffer underrun.
cdrecord: Try to use 'driveropts=burnfree'.
cdrecord: Make sure that you are root, enable DMA and check your HW/OS set up.
cdrecord: Success. test unit ready: scsi sendcmd: no error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0E 00 00 00 00 30 00 00 00 Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x30 Qual 0x00 (incompatible medium installed) Fru 0x0 Sense flags: Blk 0 (not valid)
cmd finished after 0.005s timeout 200s
Writing time: 139.113s
Average write speed 32.0x.
Min drive buffer fill was 80%
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
cdrecord: Success. flush cache: scsi sendcmd: no error
CDB: 35 00 00 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0E 00 00 00 00 30 00 00 00 Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x30 Qual 0x00 (incompatible medium installed) Fru 0x0 Sense flags: Blk 0 (not valid)
cmd finished after 0.005s timeout 200s
Trouble flushing the cache
cdrecord: Success. test unit ready: scsi sendcmd: no error
CDB: 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 02 00 00 00 00 0E 00 00 00 00 30 00 00 00 Sense Key: 0x2 Not Ready, Segment 0
Sense Code: 0x30 Qual 0x00 (incompatible medium installed) Fru 0x0 Sense flags: Blk 0 (not valid)
cmd finished after 0.006s timeout 200s
Fixating time: 26.117s
hdparm:IO_support = 3 (32-bit w/sync)
unmaskirq = 1 (on) using_dma = 1 (on) keepsettings = 0 (off) readonly = 1 (on)
In article <[email protected]>,
P. Christeas <[email protected]> wrote:
| > Hello | > | > ... | > | > There is now ide-cd writing support, and cdrecord 2 supports it. I build | > that stuff modular, so I just load the ide-cd and isofs modules (modprobe | > takes care of the rest). I achieve the fastest writing speeds I've ever | > had, using this driver. Far better than ide-scsi or even Sleazy CD Creator | > in Windows. | > | >... | | Tried it. Now used /dev/hdd there.. | This time it worked a few times and some other times it failed. | It now seems that I got a buffer underrun, although I do have 'realtime | priority' for the process. | Note that I'm not using 'burnfree'. That's why I have linux anyway :) . | | Can anybody examine why is the buffer of cdrecord less than 100% with | RR-scheduling? That would never happen in 2.4, cdrecord 1.10 ..
If you haven't solved this yet (firmware current?) you might try using a large fifo, starting a burn, then looking at the system with vmstat to see if there's a lot of system time. If so, I suspect the you are using PIO in spite of the new method and selection of DMA for the device.
In any case it will provide a data point.
Signature · 3 lines
bill davidsen <[email protected]> CTO, TMR Associates, Inc Doing interesting things with little computers since 1979.