framebuffer drawing incorrectly ?
i've been trying to get the framebuffer to work but so far havent had any luck ... i was unable to locate anyone who had a similar problem ...
Display controller: Hewlett-Packard Comp A4977A Visualize EG (rev 3). machine is a C360 ... STI Console works great ...
tried 2.4.22-pa13 and 2.6.0-test9-pa5 with same exact results
the frame buffer draws all messed up however ... it only draws on the right quarter of the screen ... the rest of the screen still contains the buffered video as found when the computer was booted (firmware output along with palo stuff) ... the colors are all skewed, basically white is purple along with a few other bit inversions of some sort ...
also, each line is drawn incorrectly ... it's like each has been split in half horizontally and then swapped ...
i can get X to load, but again it draws it all messed up in the right quarter on the screen
i wish i could post a frame buffer grab, but fbgrab doesnt support 8bit and fbscreenshot likes to segfault when writing the png to disk.
any ideas what i'm missing ?
or is the fbdriver the only way i can get X and running ? -mike
please send your xfonfig-4 and your dmesg file.
Joel
Quoted 15 lines · Mike Frysinger
i've been trying to get the framebuffer to work but so far havent had any luck ... i was unable to locate anyone who had a similar problem ...
Display controller: Hewlett-Packard Comp A4977A Visualize EG (rev 3). machine is a C360 ... STI Console works great ...
tried 2.4.22-pa13 and 2.6.0-test9-pa5 with same exact resultsthe frame buffer draws all messed up however ... it only draws on the right quarter of the screen ... the rest of the screen still contains the buffered video as found when the computer was booted (firmware output along with palo stuff) ... the colors are all skewed, basically white is purple along with a few other bit inversions of some sort ... also, each line is drawn incorrectly ... it's like each has been split in half horizontally and then swapped ...
i can get X to load, but again it draws it all messed up in the right quarter on the screeni wish i could post a frame buffer grab, but fbgrab doesnt support 8bit and fbscreenshot likes to segfault when writing the png to disk.
any ideas what i'm missing ?
or is the fbdriver the only way i can get X and running ? -mike
Quoted 2 lines · Mike Frysinger
the frame buffer draws all messed up however ... it only draws on the right quarter of the screen ... the rest of the screen still contains the buffered
try to turn off double buffering.
Quoted 1 line
or is the fbdriver the only way i can get X and running ?
yes.
Thomas.
Signature · 2 lines
Crap can work. Given enough thrust pigs will fly, but it's not necessary a good idea. [ Alexander Viro on linux-kernel ]
Le lundi, 10 nov 2003, =E0 22:46 Europe/Paris, Mike Frysinger a =E9crit = :
Quoted 5 lines
i wish i could post a frame buffer grab, but fbgrab doesnt support=20 8bit and
fbscreenshot likes to segfault when writing the png to disk.
you can try to take pics with a digital camera or a webcam, if you have any...
see: this is what we got with sticon init on 64bit kernel on B2000:
http://www.pateam.org/images/cell/pictures/B2000/B2000_sti_init800.jpg
Maybe this could help illustrating what you see?
Thibaut VARENE
The PA/Linux ESIEE Team
http://www.pateam.org/
Quoted 1 line · you
please send your xfonfig-4 and your dmesg file.
http://wh0rd.de/mike/hppa-dmesg
http://wh0rd.de/mike/hppa-XF86Config-4
http://wh0rd.de/mike/hppa-fbcon-pic.jpg
the pic is a little blurry but you can see that the white text is from the hppa firmware/palo while the purple text is from the bootup ... also, it seems that the buffer is swapped in the middle ... the lower half of the purple text is actually displayed first when scrolling back through the buffer ...
-mike
Mike,
Quoted 7 lines · Mike Frysinger
Quoted 1 line · you
please send your xfonfig-4 and your dmesg file.
http://wh0rd.de/mike/hppa-dmesg
http://wh0rd.de/mike/hppa-XF86Config-4
All seems ok. I just notice a small difference with my "Display" definition:
[...]
Section "Screen"
Identifier "Default Screen"
Device "HPA208LC1024"
Monitor "Targa"
DefaultDepth 8
SubSection "Display"
Depth 1
Modes "1280x1024"
EndSubSectionEndSection
[...]
you added:
Virtual 0 0 ViewPort 0 0
well I don't know exactely what is realy makes and I presume that you already test without (commented) those lines?
Quoted 3 lines
http://wh0rd.de/mike/hppa-fbcon-pic.jpg
the pic is a little blurry but you can see that the white text is from the hppafirmware/palowhile the purple text is from the bootup ... also, it seems that the buffer is swapped in the middle ... the lower half of the purple text is actually displayed first when scrolling back through the buffer ... -mike
hmm, i never see such behaviour before but it seems that electronic signals emitted by hp system are not compatible with your screen (bad cable, adapter?)??
[For my part I also try, here at home with a foreign screen (not hp, i mean) but it doesn't work very well (at each reboot I was obliged to fix the pdc screen definition but it was working fine with a hp screen), so i don't even test XFree more then the time of a login...)] Before you install Linux, do you have the opportunity to check if it was working with hpux X11 hpview or cde?
Or do you have some opportunity to test with a hp screen?
(or the graphical controler is broken?)
Sorry couldn't help you more.
Good luck,
Joel
Joel
Quoted 2 lines · Joel Soete
well I don't know exactely what is realy makes and I presume that you already test without (commented) those lines?
well the fb is messed up w/out X ... i just mentioned X because thats the real reason i'm messing around with it ;)
and yes, the viewport settings make no difference
Quoted 11 lines
hmm, i never see such behaviour before but it seems that electronic signals emitted by hp system are not compatible with your screen (bad cable, adapter?)??
[For my part I also try, here at home with a foreign screen (not hp, i mean) but it doesn't work very well (at each reboot I was obliged to fix the pdc screen definition but it was working fine with a hp screen), so i don't even test XFree more then the time of a login...)] Before you install Linux, do you have the opportunity to check if it was working with hpux X11 hpview or cde?
Or do you have some opportunity to test with a hp screen? (or the graphical controler is broken?)
i didnt have a chance to test it ... the box was a server that was given to me thus no display and i didnt really feel like brute forcing the passwords to get to the installed HPUX ...
as for the monitor, it's a 19" trintron that i've done resolutions much greater than 1600x1200 with before so i know it's a pretty good monitor ... i dunno about the signals as you mentioned ... but i know the STI Console works just dandy :)
perhaps i'll try some random pci cards i got laying around (voodoo/ati) and see if i have any luck with them
-mike
Quoted 8 lines · Joel Soete
Quoted 2 lines
well I don't know exactely what is realy makes and I presume that you already test without (commented) those lines?
well the fb is messed up w/out X ... i just mentioned X because thats the r= eal=20
reason i'm messing around with it ;)
and yes, the viewport settings make no difference
The X config and the mode setting for the card have to match. You probably have the card in double buffered mode. This isn't compatible with the frame buffer driver. The selected resolutions also have to match.
Dave
Signature · 2 lines
J. David Anglin [email protected] National Research Council of Canada (613) 990-0752 (FAX: 952-6602)
Quoted 1 line · you
try to turn off double buffering.
that did the trick, thanks everyone
-mike