405EP peripheral bus
Has anyone messed around with accessing the peripheral bus on a 405EP PPC? I've already written a driver to allow me to read/write to the EBC (external bus control) registers from userspace, but I can't seem to toggle CS0\, OE\, R/W, etc. Is there anything special about CS0\ (after boot)?
By default, Intrinsyc/Linux sets ups the EBC registers as follows:
EBC0_B0CR : 0xffe3a000EBC0_B1CR : 0x60018000EBC0_B2CR : 0x00000000EBC0_B3CR : 0x00000000EBC0_B4CR : 0x00000000EBC0_B0AP : 0x04002480EBC0_B1AP : 0x04005480EBC0_B2AP : 0x00000000EBC0_B3AP : 0x00000000EBC0_B4AP : 0x00000000EBC0_BEAR : 0x00000000EBC0_BESR0 : 0x00000000EBC0_BESR1 : 0x00000000EBC0_CFG : 0x80400000
and I changed B0CR to 0x0043a000 and I'm trying to use mmap like:
#define MAP_BASE (0x00400000)
#define MAP_LENGTH 0x10
#define MAP_PROT (PROT_READ | PROT_WRITE)
#define MAP_FLAGS (MAP_SHARED)
volatile unsigned char *init_map(int *file)
{
volatile unsigned char *map;
if ((*file = open("/dev/mem", O_RDWR | O_SYNC)) == -1) {
puts("Failure opening device.");
return NULL;
}
map = (unsigned char *) mmap(NULL, MAP_LENGTH, MAP_PROT, MAP_FLAGS, *file, MAP_BASE);
if (map == (void *) -1) {
puts("Failure mapping memory.");
close(*file);
return NULL;
}
return map;
}then reading/writing to the returned map address. ... any suggestions?
I have an oscilloscope and digital logical analyzer available to probe signals.
Thanks!
-Paul
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Am Mittwoch, 19. November 2003 21:43 schrieb Paul Miller:
Quoted 1 line
and I changed B0CR to
0x0043a000and I'm trying to use mmap like:
How many RAM is in your System? Less than 64MiB? Or more? Maybe there is an overlapping?
JB
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
Intrinsyc will not provide the physical address locations for anything on their board, which is ridiculous. I have determined, based on the DCR registers, that the following memory addresses are used:
SDRAM is located at 0x00000000 with 32MB size.
(NOR??) located at 0xFFE000000 with size 2MB
(NAND??) located at 0x60000000 with size 1MB
Based on Intrinsyc's code, they appear to use 0x60000000 as the base address for the NAND flash, but the register reads a 1MB size instead of 32MB. I suspect the other location is the NOR flash.
So now I'm trying to use address 0x04000000 with CS2\.
How do I map the phyiscal address?
/* EBC0 Registers */EBC0_B0CR : 0xffe3a000EBC0_B1CR : 0x60018000EBC0_B2CR : 0x00000000EBC0_B3CR : 0x00000000EBC0_B4CR : 0x00000000EBC0_B0AP : 0x04002480EBC0_B1AP : 0x04005480EBC0_B2AP : 0x00000000EBC0_B3AP : 0x00000000EBC0_B4AP : 0x00000000EBC0_BEAR : 0x00000000EBC0_BESR0 : 0x00000000EBC0_BESR1 : 0x00000000EBC0_CFG : 0x80400000
/* SDRAM0 Registers */SDRAM0_CFG : 0x80a00000SDRAM0_STATUS: 0x80000000SDRAM0_RTR : 0x07e80000SDRAM0_PMIT : 0x07c00000SDRAM0_B0CR : 0x00062001SDRAM0_B1CR : 0x00000000SDRAM0_TR : 0x010bc01b
Setting up EBC registers...EBC0_B2CR: 0x0403a000EBC0_B2AP: 0x04002480
Thanks!
-Paul
Quoted 9 lines · Juergen Beisert
Am Mittwoch, 19. November 2003 21:43 schrieb Paul Miller:
Quoted 1 line
and I changed B0CR to
0x0043a000and I'm trying to use mmap like:How many RAM is in your System? Less than 64MiB? Or more? Maybe there is an overlapping?
JB
** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/