2.6.0-test11, PCMCIA,, Cirrus CL 6729 bridge not working
I've been trying to get my PCMCIA bridge to work with 2.6.0-test11, but without any luck sofar. My bridge works perfectly with 2.4.X series kernels and pcmcia-cs-3.2.5 kernel modules (i82365, with module options: irq_mode=1 fast_pci=1).
It is a PCI-to-PCMCIA bridge based on Cirrus Logic CL 6729 (rev 07).
Is there a way to get it working under 2.6 series kernels ? (as pcmcia-cs is not going to be supported for 2.6 series kernels).
Some dumps from the session:
root@flamepygmy flame # modprobe yenta_socket
root@flamepygmy flame # cardmgr
cardmgr[3834]: no sockets found!
root@flamepygmy flame # modprobe i82092
root@flamepygmy flame # cardmgr
cardmgr[3839]: no sockets found!
root@flamepygmy flame # modprobe tcic
FATAL: Error inserting tcic (/lib/modules/2.6.0-test11/kernel/drivers/pcmcia/tcic.ko): No such device
root@flamepygmy flame # pcic_probe
PCI bridge probe: Cirrus Logic CL 6729 found, 2 sockets.
root@flamepygmy flame # pcic_probe -m
i82365
root@flamepygmy flame # lspci
00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:09.0 USB Controller: VIA Technologies, Inc. USB (rev 50)
00:09.1 USB Controller: VIA Technologies, Inc. USB (rev 50)
00:09.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51)
00:0d.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 00:0e.0 PCMCIA bridge: Cirrus Logic CL 6729 (rev 07)
00:0f.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
00:0f.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
00:10.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) 00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 23)
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 23)
01:00.0 VGA compatible controller: ATI Technologies Inc: Unknown device 4150
01:00.1 Display controller: ATI Technologies Inc: Unknown device 4170
root@flamepygmy flame # lspci -vvx
<clipped>
00:0e.0 PCMCIA bridge: Cirrus Logic CL 6729 (rev 07)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at a400 [disabled] [size=4]
00: 13 10 00 11 80 00 00 04 07 00 05 06 00 00 00 00
10: 01 a4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
--jani;
Quoted 2 lines · Jani Vaarala
It is a PCI-to-PCMCIA bridge based on Cirrus Logic CL 6729 (rev 07).
Whee. Those are getting rare.
Anyway, it really looks like it's a _PCMCIA_ bridge, not a cardbus one, so you can forget about the yenta module. Basically, "yenta" is for the newer 32-bit-capable Cardbus bridges (which do have an i82365 compatible legacy mode), and i82365 is for the old legacy-_only_ 16-bit PCMCIA bridges.
It should be an i82365-compatible chip (they almost always are - it's either yenta or i82365 in the normal case, and the others are for some really odd-ball things or non-PC-compatibles).
It looks like you tried every single module _except_ for the i82365.
Give that one a whirl. Just "modprobe i82365"
Linus