dpt/adaptec i2o trouble (long)
Hi,
I own a dpt smart raid v (1554U2) scsi controller, for wich i used the dpt_i2o driver under kernel 2.4, wich is currently broken in 2.6. I googled a bit around, and found out that the suggested solution is to use use the i2o-scsi driver:
http://marc.theaimsgroup.com/?l=linux-scsi&m=106046024506801&w=2
also see this thread:
http://marc.theaimsgroup.com/?t=106191158100004&r=1&w=2
So i compiled a fresh 2.6.0-test11 kernel, and build i2o-core, i2o-proc, i2o-scsi and i2o-block as modules.
While modprobing i2o-core without parameters it told me:
"Skipping Adaptec/DPT I2O raid with preferred native driver."
with "dpt=1" the module loads, but it complains that it cant
get the size of the device:
--
Activating I2O controllers...
This may take a few minutes if there are many devices i2o/iop0: LCT has 15 entries.i2o_scsi.c: Version 0.1.2
chain_pool: 2048 bytes @ df1a7800
(512 byte buffers X 4 can_queue X 1 i2o controllers)
--> PARAMS_GET - Error:
--> ErrorInfoSize = 0x01, BlockStatus = 0x08, BlockSize = 0x0002
scsi1 : i2o/iop0
Vendor: IBM Model: DDRS-39130W Rev: S97B
Type: Direct-Access ANSI SCSI revision: 02
--> sda : READ CAPACITY failed. --> sda : status=0, message=00, host=7, driver=00 --> sda : sense not available.
SCSI device sda: drive cache: write back
sda: sda1
Attached scsi disk sda at scsi1, channel 0, id 2, lun 0 Attached scsi generic sg1 at scsi1, channel 0, id 2, lun 0, type 0 --
in this state fdisk tells me the following:
--
Disk /dev/sda: 1073 MB, 1073741824 bytes
255 heads, 63 sectors/track, 130 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Device Boot Start End Blocks Id System
/dev/sda1 1 1111 8924076 83 Linux
Partition 1 has different physical/logical endings:
phys=(1023, 254, 63) logical=(1110, 254, 63)--
which is wrong, because the attached harddisk (i dont use the raid features of this controller) is an ibm ddrs-39130w -> size = 9.1 gb
on 2.4, using the dpt_i2o driver, i dont experience this problems:
--
Loading Adaptec I2O RAID: Version 2.4 Build 5
Detecting Adaptec I2O RAID controllers...
PCI: Found IRQ 5 for device 00:0d.1
Adaptec I2O RAID controller 0 at e14b0000 size=100000 irq=5
dpti: If you have a lot of devices this could take a few minutes.
dpti0: Reading the hardware resource table.
TID 008 Vendor: SYMBIOS Device: SYM53C895 Rev: 00000001
TID 515 Vendor: IBM Device: DDRS-39130W Rev: S97B
scsi2 : Vendor: Adaptec Model: PM1554U2 FW:3013
Vendor: IBM Model: DDRS-39130W Rev: S97B
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi disk sda at scsi2, channel 0, id 2, lun 0 SCSI device sda: 17849983 512-byte hdwr sectors (9139 MB)
sda: sda1
--
i´ve put up further information (log entries,...) here:
http://segfault.info/simon/i2o/
my .config:
http://segfault.info/simon/i2o/2.6.0-test11.config
best regards,
simon.