CD-ROMs not working in 2.6
Hi all,
I'd appreciate a CC as I'm not subbed.
I'm running 2.6.0 from the Debian source packages. All is good, except my CDROM drives don't work. Here's some relevant output from /var/log/dmesg:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0x8800-0x8807, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x8808-0x880f, BIOS settings: hdc:DMA, hdd:piohdc: 54X CD-ROM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15end_request: I/O error, dev hdc, sector 0
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
libata version 0.81 loaded.sata_promise version 0.86
ata1: SATA max UDMA/133 cmd 0xE0824200 ctl 0xE0824238 bmdma 0x0 irq 17
ata2: SATA max UDMA/133 cmd 0xE0824280 ctl 0xE08242B8 bmdma 0x0 irq 17
Now lspci:
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
Can anyone shed any light on this? I've tried a different IDE cable. I disconnected the other drive that was the slave, but no dice. hdc and hdd both reported the I/O error when they were both connected. The system doesn't recognise data or audio discs.
I won't post my kernel config without request as it's 1151 lines long.
A
Quoted 31 lines · Antony Gelberg
Hi all,
I'd appreciate a CC as I'm not subbed.
I'm running 2.6.0 from the Debian source packages. All is good, except my CDROM drives don't work. Here's some relevant output from
/var/log/dmesg:Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: No IRQ known for interrupt pin A of device 0000:00:11.1 - using IRQ 255VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1ide0: BM-DMA at 0x8800-0x8807, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x8808-0x880f, BIOS settings: hdc:DMA, hdd:piohdc: 54X CD-ROM, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15end_request: I/O error, dev hdc, sector 0
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
libata version 0.81 loaded.sata_promiseversion 0.86
ata1: SATA max UDMA/133 cmd0xE0824200ctl0xE0824238bmdma0x0irq 17
ata2: SATA max UDMA/133 cmd0xE0824280ctl0xE08242B8bmdma0x0irq 17
Quoted 8 lines
Now lspci:
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)Can anyone shed any light on this? I've tried a different IDE cable. I disconnected the other drive that was the slave, but no dice. hdc and hdd both reported the I/O error when they were both connected. The system doesn't recognise data or audio discs.
Maybe if you would let us know what doesn't work?! At least post the full boot messages and make sure you aren't doing anything like passing hdc/d=ide-scsi through lile/grub.
Signature · 1 line
Jens Axboe