tg3 error
A machine at a customer's site (running kernel 2.4.21) has stopped answering over Ethernet today. The machine itself was still there and the customer could log in at the console. A reboot fixed the problem.
The machine has had these error messages in the syslog about once per hour for about 24 hours:
Mar 9 16:17:38 mail2 kernel: tg3: eth0: transmit timed out, resetting Mar 9 16:17:38 mail2 kernel: tg3: tg3_stop_block timed out, ofs=3400 enable_bit=2 Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=2400 enable_bit=2 Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=1400 enable_bit=2 Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=c00 enable_bit=2
The hardware is on-board on an IBM eServer pizza box, a dual broadcom gigabit ethernet NIC. Any ideas what might have caused this and what we should do to prevent this from happening again?
Thanks,
Felix
Quoted 4 lines · Felix von Leitner
A machine at a customer's site (running kernel 2.4.21) has stopped answering over Ethernet today. The machine itself was still there and the customer could log in at the console. A reboot fixed the problem.
Quoted 8 lines
The machine has had these error messages in the syslog about once per hour for about 24 hours:
Mar 9 16:17:38 mail2 kernel: tg3: eth0: transmit timed out, resetting Mar 9 16:17:38 mail2 kernel: tg3: tg3_stop_block timed out, ofs=3400 enable_bit=2 Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=2400 enable_bit=2 Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=1400 enable_bit=2 Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=c00 enable_bit=2
AFAIK this is fixed in the latest upstream tg3...
Jeff
Quoted 10 lines
Quoted 9 lines · Felix von Leitner
A machine at a customer's site (running kernel 2.4.21) has stopped answering over Ethernet today. The machine itself was still there and the customer could log in at the console. A reboot fixed the problem.
The machine has had these error messages in the syslog about once per hour for about 24 hours:
Mar 9 16:17:38 mail2 kernel: tg3: eth0: transmit timed out, resetting Mar 9 16:17:38 mail2 kernel: tg3: tg3_stop_block timed out, ofs=3400
enable_bit=2
Quoted 1 line
Quoted 1 line
Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=2400
enable_bit=2
Quoted 1 line
Quoted 1 line
Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=1400
enable_bit=2
Quoted 1 line
Quoted 1 line
Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=c00
enable_bit=2
Quoted 3 lines
AFAIK this is fixed in the latest upstream tg3...
I have exactly the same problems in 2.4.25 - the log says exactly the same as for Felix.
I'm running two identical HP ProLiant servers but have this problem only on one of them.
It's happening approximately twice a week.
Any ideas?
Thank you,
--
C.
Quoted 21 lines · Kamil Srot
Quoted 10 lines
Quoted 9 lines · Felix von Leitner
A machine at a customer's site (running kernel 2.4.21) has stopped answering over Ethernet today. The machine itself was still there and the customer could log in at the console. A reboot fixed the problem.
The machine has had these error messages in the syslog about once per hour for about 24 hours:
Mar 9 16:17:38 mail2 kernel: tg3: eth0: transmit timed out, resetting Mar 9 16:17:38 mail2 kernel: tg3: tg3_stop_block timed out, ofs=3400enable_bit=2
Quoted 1 line
Quoted 1 line
Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=2400enable_bit=2
Quoted 1 line
Quoted 1 line
Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=1400enable_bit=2
Quoted 1 line
Quoted 1 line
Mar 9 16:17:39 mail2 kernel: tg3: tg3_stop_block timed out, ofs=c00enable_bit=2
Quoted 3 lines
AFAIK this is fixed in the latest upstream tg3...
Quoted 8 lines
I have exactly the same problems in 2.4.25 - the log says exactly the same as for Felix.
I'm running two identical HP ProLiant servers but have this problem only on one of them.
It's happening approximately twice a week.Any ideas?
Just to pipe in; I have a machine (HP 530cmt) running RHEL3 no the latest kernel, running with the tg3-driver for the onboard eth, and if requires the i/f to be taken down and up again to start speaking, or even negotiating an eth-link. Hardware at the other end is a cisco switch.
mvh,
A
Signature · 3 lines
Alexander Hoogerhuis | [email protected] CCNP - CCDP - MCNE - CCSE | +47 908 21 485 "You have zero privacy anyway. Get over it." --Scott McNealy