Problems running latencytest: "error setting freq 1024"
Hallo,
I'd like to test my system's 2.6.4 latency using Takashi's
http://www.alsa-project.org/~iwai/latencytest-0.5.2.tar.gz
suite.
Building and installing so far went fine, I can run all the tests but no output is created. But I get a spurious error message which could be the reason for this. If I run "measure" by hand as it is called by "run_tests" like this:
$ measure -p ./out/x11.png -o ./out/x11.out -c 0 -f 1024 -n 2 -t 2 I get this error message: "error setting freq 1024"
This seems to have something to do with the rtc-clock, but I have no idea, what could be wrong here. Maybe it's something with my kernel config? It looks like this:
$ grep -i rtc /boot/config-2.6.4 # CONFIG_HPET_EMULATE_RTC is not set # CONFIG_APM_RTC_IS_GMT is not set CONFIG_RTC=m CONFIG_GEN_RTC=m CONFIG_GEN_RTC_X=y CONFIG_SND_RTCTIMER=m
Modules latency_test and rtc are loaded.
Any ideas?
ciao
Signature · 8 lines
Frank Barknecht _ ______footils.org__ ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 2 lines
$ measure -p ./out/x11.png -o ./out/x11.out -c 0 -f 1024 -n 2 -t 2 I get this error message: "error setting freq 1024"
probably a permissions problem. try it as root.
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Hallo,
Quoted 4 lines · Paul Davis hat gesagt: // Paul Davis wrote:
Quoted 2 lines
$ measure -p ./out/x11.png -o ./out/x11.out -c 0 -f 1024 -n 2 -t 2 I get this error message: "error setting freq 1024"probably a permissions problem. try it as root.
This is while runng at root. (Sorry for the "$" I typed that one by hand).
A tip from Tim Goetze to do:
# echo 2048 > /proc/sys/dev/rtc/max-user-freq (^ sic!)
didn't help either yet. I did a strace on the measure run now, which showed something equally strange (to my eyes):
mlockall(MCL_CURRENT|MCL_FUTURE) = 0
sched_get_priority_max(0x1) = 99
sched_setscheduler(0, 0x1, 0xbfffe254) = 0
open("/dev/midi0", O_RDWR) = 3
ioctl(3, 0x40047401, 0x400) = -1 ENOTTY (Inappropriate ioctl for device)write(2, "error setting freq 1024\n", 24) = 24exit_group(1) = ?
I'm still puzzled. Why "/dev/midi0"?
ciao
Signature · 8 lines
Frank Barknecht _ ______footils.org__ ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 21 lines
Quoted 4 lines
Quoted 2 lines
$ measure -p ./out/x11.png -o ./out/x11.out -c 0 -f 1024 -n 2 -t 2 I get this error message: "error setting freq 1024"probably a permissions problem. try it as root.
This is while runng at root. (Sorry for the "$" I typed that one by hand).
A tip from Tim Goetze to do:
# echo 2048 > /proc/sys/dev/rtc/max-user-freq (^ sic!)didn't help either yet. I did a strace on the measure run now, which showed something equally strange (to my eyes):
mlockall(MCL_CURRENT|MCL_FUTURE) = 0 sched_get_priority_max(0x1) = 99 sched_setscheduler(0, 0x1, 0xbfffe254) = 0 open("/dev/midi0", O_RDWR) = 3 ioctl(3, 0x40047401, 0x400) = -1 ENOTTY (Inappropriate ioctl for device)
Quoted 4 lines
write(2, "error setting freq 1024\n", 24)= 24exit_group(1)= ?I'm still puzzled. Why "
/dev/midi0"?
Takashi is apparently using that to communicate with the latency test kernel module (I think he mentions it in the README :-)
I have it running here with no problems, will post pointers to some results (2.6.4 + 2.6.5rc2 + bk2 + lsm + drm lowlat patches, w and w/o preempt).
-- Fernando
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 6 lines · Frank Barknecht
Hallo,
I'd like to test my system's 2.6.4 latency using Takashi's
http://www.alsa-project.org/~iwai/latencytest-0.5.2.tar.gz
suite.
Quoted 6 lines
Building and installing so far went fine, I can run all the tests but no output is created. But I get a spurious error message which could be the reason for this. If I run "measure" by hand as it is called by "
run_tests" like this:$ measure -p ./out/x11.png -o ./out/x11.out -c 0 -f 1024 -n 2 -t 2 I get this error message: "error setting freq 1024"
Frequency should be equal or greater than 5000Hz.
Jaroslav
-----
Jaroslav Kysela <[email protected]>
Linux Kernel Sound Maintainer
ALSA Project, SuSE Labs
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Quoted 4 lines · Jaroslav Kysela
Quoted 2 lines
$ measure -p ./out/x11.png -o ./out/x11.out -c 0 -f 1024 -n 2 -t 2 I get this error message: "error setting freq 1024"Frequency should be equal or greater than 5000Hz.
Sorry, it appears to be the rtc frequency, of course. I was referring to the PCM rate.
Jaroslav
-----
Jaroslav Kysela <[email protected]>
Linux Kernel Sound Maintainer
ALSA Project, SuSE Labs
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
At Tue, 23 Mar 2004 22:42:05 +0100,
Quoted 20 lines · Frank Barknecht
Hallo,
Quoted 4 lines · Paul Davis hat gesagt: // Paul Davis wrote:
Quoted 2 lines
$ measure -p ./out/x11.png -o ./out/x11.out -c 0 -f 1024 -n 2 -t 2 I get this error message: "error setting freq 1024"probably a permissions problem. try it as root.
This is while runng at root. (Sorry for the "$" I typed that one by hand).
A tip from Tim Goetze to do:
# echo 2048 > /proc/sys/dev/rtc/max-user-freq (^ sic!)didn't help either yet. I did a strace on the measure run now, which showed something equally strange (to my eyes):
Quoted 7 lines
mlockall(MCL_CURRENT|MCL_FUTURE) = 0 sched_get_priority_max(0x1) = 99 sched_setscheduler(0, 0x1, 0xbfffe254) = 0 open("/dev/midi0", O_RDWR) = 3 ioctl(3, 0x40047401, 0x400) = -1 ENOTTY (Inappropriate ioctl for device)
write(2, "error setting freq 1024\n", 24)= 24exit_group(1)= ?
please make sure that you loaded latency-test module.
Quoted 1 line
I'm still puzzled. Why "
/dev/midi0"?
that's because the latency-test kernel module requires a device file for ioctls. i chose it simply because the file is unused (it's for tclmidi).
BTW, i uploaded latencytest-0.5.3. it includes i/o workloads in parallel.
http://www.alsa-project.org/~iwai/latencytest-0.5.3.tar.gz
Takashi
-------------------------------------------------------
This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click
Hallo,
Quoted 11 lines · Takashi Iwai hat gesagt: // Takashi Iwai wrote:
At Tue, 23 Mar 2004 22:42:05 +0100,
Quoted 7 lines · Frank Barknecht
mlockall(MCL_CURRENT|MCL_FUTURE) = 0 sched_get_priority_max(0x1) = 99 sched_setscheduler(0, 0x1, 0xbfffe254) = 0 open("/dev/midi0", O_RDWR) = 3 ioctl(3, 0x40047401, 0x400) = -1 ENOTTY (Inappropriate ioctl for device)
write(2, "error setting freq 1024\n", 24)= 24exit_group(1)= ?please make sure that you loaded latency-test module.
Yes, it is loaded.
Quoted 5 lines
Quoted 1 line
I'm still puzzled. Why "
/dev/midi0"?that's because the latency-test kernel module requires a device file for ioctls. i chose it simply because the file is unused (it's for tclmidi).
Maybe that is my problem. Here, /dev/midi is a link to /dev/midi0:
$ ls -l /dev/midi lrwxrwxrwx 1 root root 10 Jul 30 2003 /dev/midi -> /dev/midi0 $ ls -l /dev/midi0 crw-rw---- 1 root audio 14, 2 Jul 30 2003 /dev/midi0
I don't know why it is set up this way, but on another machine I can ssh to it looks different:
$ ls -l /dev/midi lrwxrwxrwx 1 root root 6 May 27 2003 /dev/midi -> midi00 $ ls -l /dev/midi0 crw-rw-rw- 1 root audio 35, 0 Mar 14 2003 /dev/midi0
Here I get the device number 35 for midi0, and another symlink.
Did I mess up big time?
ciao
Signature · 8 lines
Frank Barknecht _ ______footils.org__ ------------------------------------------------------- This SF.Net email is sponsored by: IBM Linux Tutorials Free Linux tutorial presented by Daniel Robbins, President and CEO of GenToo technologies. Learn everything from fundamentals to system administration.http://ads.osdn.com/?ad_id=1470&alloc_id=3638&op=click