Problems with my parport (and printer)
Hi all :)
I have a printer connected thru my parallel port, supported in
the kernel by parport+parport_pc+lp:
kernel: parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
kernel: parport0: Printer, Lexmark International Lexmark Optra E312
kernel: lp0: using parport0 (interrupt-driven).
kernel: lp0: console ready
It works ok, BTW... The problem is that, when the printer is
switched of and I try to print something, the print command just blocks, no error, no messages, nothing. I use a shell function to print, which sends a control command to the printer and after that sends the file I want to print. It stops (forever) at the reset command, something like "echo -n '\eE' > /dev/printer".
Why this operation doesn't fail? IMHO, it should fail with
ENODEV, because parport can work (the parallel port is there...), but lp shouldn't (the printer is switched off...).
BTW, I would swear I have the parallel port configured as EPP+ECP
with DMA3 and irq 7 :??? Why is it detected as PCSPP?
Any help? Thanks in advance :)
Raúl Núñez de Arenas Coronado
Signature · 2 lines
Linux Registered User 88736 http://www.pleyades.net & http://raul.pleyades.net/
On Thu, 2004-03-25 12:51:31 +0100, DervishD <[email protected]> wrote in message <20040325115131.GA12195@DervishD>:
Quoted 5 lines
Hi all :)
I have a printer connected thru my parallel port, supported in
the kernel by parport+parport_pc+lp:
Quoted 8 lines
kernel: parport0: PC-style at
0x378(0x778), irq 7 [PCSPP,TRISTATE]
kernel: parport0: Printer, Lexmark International Lexmark Optra E312
kernel: lp0: using parport0 (interrupt-driven).
kernel: lp0: console readyIt works ok, BTW... The problem is that, when the printer is
switched of and I try to print something, the print command just blocks, no error, no messages, nothing. I use a shell function to
First of all, if you want to do normal printing, you shouldn't switch on LP console. From there on, all kernel debug output (as seen in /var/log/kern.log and outputted with "dmesg") would be sent to the printer, what isn't exactly what you want to have.
Quoted 3 lines
Why this operation doesn't fail? IMHO, it should fail with
ENODEV, because parport can work (the parallel port is there...), but lp shouldn't (the printer is switched off...).
Another gotcha may be that your printer doesn't easily accept commands. Many printers don't do that nowadays. Some are dumb GDI-Printerts (Windows-only, that is...), some nees specific wake-up sequences.
MfG, JBG
Signature · 4 lines
Jan-Benedict Glaw [email protected] . +49-172-7608481 "Eine Freie Meinung in einem Freien Kopf | Gegen Zensur | Gegen Krieg fuer einen Freien Staat voll Freier Bürger" | im Internet! | im Irak! ret = do_actions((curr | FREE_SPEECH) & ~(NEW_COPYRIGHT_LAW | DRM | TCPA));
Hi Jan :)
* Jan-Benedict Glaw <[email protected]> dixit:
Quoted 11 lines
Quoted 7 lines
kernel: parport0: PC-style at
0x378(0x778), irq 7 [PCSPP,TRISTATE]
kernel: parport0: Printer, Lexmark International Lexmark Optra E312
kernel: lp0: using parport0 (interrupt-driven).
kernel: lp0: console ready
It works ok, BTW... The problem is that, when the printer is
switched of and I try to print something, the print command just blocks, no error, no messages, nothing. I use a shell function toFirst of all, if you want to do normal printing, you shouldn't switch on LP console. From there on, all kernel debug output (as seen in
/var/log/kern.logand outputted with "dmesg") would be sent to the printer, what isn't exactly what you want to have.
That's right, but LP console must be activated at boot time (or
at module-loading time) AFAIK, so this is not the problem.
Quoted 6 lines
Quoted 3 lines
Why this operation doesn't fail? IMHO, it should fail with
ENODEV, because parport can work (the parallel port is there...), but lp shouldn't (the printer is switched off...).Another gotcha may be that your printer doesn't easily accept commands. Many printers don't do that nowadays. Some are dumb GDI-Printerts (Windows-only, that is...), some nees specific wake-up sequences.
This printer (Lexmark Optra E312) is not a winprinter, and the
problem is not related to commands. The printer works fine, I have no problems with that. My problem arises when the printer is offline:
when I send data to the printer and it is not connected, the command used to send that data doesn't fail, just waits forever...
Thanks for your answer anyway :) Really I'm not familiar with the
parallel port :(
Raúl Núñez de Arenas Coronado
Signature · 2 lines
Linux Registered User 88736 http://www.pleyades.net & http://raul.pleyades.net/