Skip to contentSkip to conversation

PATCH: First cut at fixing the 3c59x power mismanagment

PATCH Alan Cox 2 participants 2 messages May 30, 2004 Networking

lore
Share & tools
lore

Alan Cox

author
#0 lore raw

In Fedora 2 there have been lots of problem reports with 3c59x mostly apparently linked to power handling errors. In particular tools query the MII state of down interfaces.

The changes here

- Power the chip up when doing MII, much as e100 does
- Fix a case where the error handling issued commands to the chip
while it was in D3 state
- Fixed a case where shutdown handling issued commands to the chip
while it was in D3 state

I don't have enough suitable hardware to do good coverage testing on these changes so test reports would be appreciated.

Alan

net/3c59x.c renamed from linux.vanilla-2.6.6/drivers/net/3c59x.c +34 -9
@@ -884,7 +884,7 @@
 static int vortex_probe1(struct device *gendev, long ioaddr, int irq,
 				   int chip_idx, int card_idx);
 static void vortex_up(struct net_device *dev);
-static void vortex_down(struct net_device *dev);
+static void vortex_down(struct net_device *dev, int final);
 static int vortex_open(struct net_device *dev);
 static void mdio_sync(long ioaddr, int bits);
 static int mdio_read(struct net_device *dev, int phy_id, int location);
@@ -948,7 +948,7 @@
 	if (dev && dev->priv) {
 		if (netif_running(dev)) {
 			netif_device_detach(dev);
-			vortex_down(dev);
+			vortex_down(dev, 1);
 		}
 	}
 	return 0;
@@ -2059,7 +2059,8 @@
 				printk(KERN_ERR "%s: PCI bus error, bus status %8.8x\n", dev->name, bus_status);
 
 			/* In this case, blow the card away */
-			vortex_down(dev);
+			/* Must not enter D3 or we can't legally issue the reset! */
+			vortex_down(dev, 0);
 			issue_and_wait(dev, TotalReset | 0xff);
 			vortex_up(dev);		/* AKPM: bug.  vortex_up() assumes that the rx ring is full. It may not be. */
 		} else if (fifo_diag & 0x0400)
@@ -2656,7 +2657,7 @@
 }
 
 static void
-vortex_down(struct net_device *dev)
+vortex_down(struct net_device *dev, int final_down)
 {
 	struct vortex_private *vp = netdev_priv(dev);
 	long ioaddr = dev->base_addr;
@@ -2685,7 +2686,7 @@
 	if (vp->full_bus_master_tx)
 		outl(0, ioaddr + DownListPtr);
 
-	if (VORTEX_PCI(vp) && vp->enable_wol) {
+	if (final_down && VORTEX_PCI(vp) && vp->enable_wol) {
 		pci_save_state(VORTEX_PCI(vp), vp->power_state);
 		acpi_set_WOL(dev);
 	}
@@ -2699,7 +2700,7 @@
 	int i;
 
 	if (netif_device_present(dev))
-		vortex_down(dev);
+		vortex_down(dev, 1);
 
 	if (vortex_debug > 1) {
 		printk(KERN_DEBUG"%s: vortex_close() status %4.4x, Tx status %2.2x.\n",
@@ -2869,7 +2870,7 @@
 	.get_drvinfo =		vortex_get_drvinfo,
 };
 
-static int vortex_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+static int vortex_do_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
 {
 	struct vortex_private *vp = netdev_priv(dev);
 	long ioaddr = dev->base_addr;
@@ -2904,6 +2905,30 @@
 	return retval;
 }
 
+/*
+ *	Must power the device up to do MDIO operations
+ */
+static int vortex_ioctl(struct net_device *dev, struct ifreq *rq, int cmd)
+{
+	int err;
+	struct vortex_private *vp = netdev_priv(dev);
+	int state = 0;
+	
+	if(VORTEX_PCI(vp))
+		state = VORTEX_PCI(vp)->current_state;
+
+	/* The kernel core really should have pci_get_power_state() */
+
+	if(state != 0)
+		pci_set_power_state(VORTEX_PCI(vp), 0);	
+	err = vortex_do_ioctl(dev, rq, cmd);
+	if(state != 0)
+		pci_set_power_state(VORTEX_PCI(vp), state);	
+	
+	return err;
+}
+
+
 /* Pre-Cyclone chips have no documented multicast filter, so the only
    multicast setting is to receive all multicast frames.  At least
    the chip has a very clean way to set the mode, unlike many others. */
@@ -3059,14 +3084,14 @@
 	 * here
 	 */
 	unregister_netdev(dev);
-	/* Should really use issue_and_wait() here */
-	outw(TotalReset|0x14, dev->base_addr + EL3_CMD);
 
 	if (VORTEX_PCI(vp) && vp->enable_wol) {
 		pci_set_power_state(VORTEX_PCI(vp), 0);	/* Go active */
 		if (vp->pm_state_valid)
 			pci_restore_state(VORTEX_PCI(vp), vp->power_state);
 	}
+	/* Should really use issue_and_wait() here */
+	outw(TotalReset|0x14, dev->base_addr + EL3_CMD);
 
 	pci_free_consistent(pdev,
 						sizeof(struct boom_rx_desc) * RX_RING_SIZE
#1 lore raw
Quoted 11 lines · Alan Cox

In Fedora 2 there have been lots of problem reports with 3c59x mostly apparently linked to power handling errors. In particular tools query the MII state of down interfaces.

The changes here

(quoted diff) +0 -2
-	Power the chip up when doing MII, much as e100 does
-	Fix a case where the error handling issued commands to the chip

while it was in D3 state

(quoted diff) +0 -1
-	Fixed a case where shutdown handling issued commands to the chip

while it was in D3 state

Quoted 2 lines

I don't have enough suitable hardware to do good coverage testing on these changes so test reports would be appreciated.

Initial review of the patch looks good, FWIW.

Thanks for poking at this,

Jeff