Skip to contentSkip to conversation

the "cisco vs. Linux" thread

LARTC Glen Mabey 11 participants 21 messages Jul 8, 2004 – Jul 13, 2004

lore
Share & tools
lore

Glen Mabey

author
#0 lore raw
Quoted 3 lines · Jos? Ildefonso Camargo Tolosa

you can use an Athlon
64 with DDR RAM and very good network hardware (that is very, very important)

Regarding NICs, are there any recommendations out there for which manufacturers to go with? I don't need anything faster than 100baseT.

I would think that Intel and 3Com would be in the "reliable" category, and RTL-based cards in the "forget it" category.

On the Intel note, I wonder what experience y'all have had with the two different drivers for the EtherExpressPro/100 card. That is, eepro100 versus e100. I would think that noone would take the time to rewrite a driver if there wasn't anything wrong with the original one.

Thank you--
Glen Mabey

Signature · 8 lines
******************************************************************
Glen W. Mabey
[email protected]
http://mabeys.homelinux.com/glen/
******************************************************************
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#1 lore raw
Quoted 13 lines · Glen Mabey
Quoted 3 lines · Jos? Ildefonso Camargo Tolosa

you can use an Athlon
64 with DDR RAM and very good network hardware (that is very, very important)

Regarding NICs, are there any recommendations out there for which manufacturers to go with? I don't need anything faster than 100baseT.

I would think that Intel and 3Com would be in the "reliable" category, and RTL-based cards in the "forget it" category.

Quoted 8 lines

On the Intel note, I wonder what experience y'all have had with the two different drivers for the EtherExpressPro/100 card. That is, eepro100 versus e100. I would think that noone would take the time to rewrite a driver if there wasn't anything wrong with the original one.

Thank you--
Glen Mabey

I have had some good luck with Intel cards using either drivers. I haven't noticed much difference between them but I haen't done a lot of stress testing on them.

On a side note has anyone built a linux router with dual/quad port ethernet cards (ie Intel PRO/1000 MT Quad Port Server Adapter)?
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Glen Mabey
Quoted 13 lines · Glen Mabey
Quoted 3 lines · Jos? Ildefonso Camargo Tolosa

you can use an Athlon
64 with DDR RAM and very good network hardware (that is very, very important)

Regarding NICs, are there any recommendations out there for which manufacturers to go with? I don't need anything faster than 100baseT.

I would think that Intel and 3Com would be in the "reliable" category, and RTL-based cards in the "forget it" category.

Quoted 8 lines

On the Intel note, I wonder what experience y'all have had with the two different drivers for the EtherExpressPro/100 card. That is, eepro100 versus e100. I would think that noone would take the time to rewrite a driver if there wasn't anything wrong with the original one.

Thank you--
Glen Mabey

I have had some good luck with Intel cards using either drivers. I haven't noticed much difference between them but I haen't done a lot of stress testing on them.

On a side note has anyone built a linux router with dual/quad port ethernet cards (ie Intel PRO/1000 MT Quad Port Server Adapter)?

--Nick Erkert
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#3 lore raw
In reply to Glen Mabey

FYI this topic has been covered on the Zebra and Quagga lists

- hardware processors, memory, NICs, etc
- software OS (Linux, *BSD), drivers, etc

I've been running a couple of Linux routers for about 2 years now, I'm using
them as core routers so I bought a couple of rackmount "server" boxes with
redundant PSUs and h/w RAID (1) for hotswap disks.

I'm using a couple of Adaptec Quartet66 NICs in each, that gives me 2 x 1GbE (on mobo) and 8 x 10/100 Mb ports per box.

Regards,

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Nicholas Erkert
Sent: 08 July 2004 22:44
To: [email protected]
Subject: Re: [LARTC] the "cisco vs. Linux" thread

Quoted 1 line · Glen Mabey

On Thu, Jul 08, 2004 at 12:07:57PM -0400, Jos? Ildefonso Camargo

Quoted 13 lines · Tolosa
Quoted 4 lines

you can use an Athlon
64 with DDR RAM and very good network hardware (that is very, very important)

Regarding NICs, are there any recommendations out there for which manufacturers to go with? I don't need anything faster than 100baseT.

I would think that Intel and 3Com would be in the "reliable" category,

and RTL-based cards in the "forget it" category.

Quoted 9 lines

On the Intel note, I wonder what experience y'all have had with the two different drivers for the EtherExpressPro/100 card. That is, eepro100 versus e100. I would think that noone would take the time to

rewrite a driver if there wasn't anything wrong with the original one.

Thank you--
Glen Mabey

I have had some good luck with Intel cards using either drivers. I haven't noticed much difference between them but I haen't done a lot of stress testing on them.

On a side note has anyone built a linux router with dual/quad port ethernet cards (ie Intel PRO/1000 MT Quad Port Server Adapter)?

--Nick Erkert
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

------------------------------------------------------------------------
Confidentiality Note: The information contained in this email and
document(s) attached are for the exclusive use of the addressee and may contain confidential, privileged and non-disclosable information. If the recipient of this email is not the addressee, such recipient is strictly prohibited from reading, photocopying, distribution or otherwise using this email or its contents in any way. Please notify the Sapiens (UK) Ltd. Systems Administrator via e-mail immediately at [email protected], if you have received this email in error.

Disclaimer: The views, opinions and guidelines contained in this confidential e-mail are those of the originating author and may not be representative of Sapiens (UK) Ltd.
------------------------------------------------------------------------
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

author
#5 lore raw
In reply to Glen Mabey
Quoted 3 lines · Alfie Viechweg

Regarding building your own router/switch. You might want to check out www.routerboard.com for a
really reasonably priced 4 port NIC.

I had no idea this type of board existed! (forgive my excitement)

Alfie, have you used the Routerboard 230 or 240 products? Anyone else?

Could anyone else recommend other manufacturers of this type of
hardware: an embedded system board with
* a couple of NICs
* PCMCIA
* runs linux

Thanks --
Glen

Signature · 8 lines
******************************************************************
Glen W. Mabey
[email protected]
http://mabeys.homelinux.com/glen/
******************************************************************
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
author
#6 lore raw
In reply to Glen Mabey
Quoted 1 line · glen

Alfie, have you used the Routerboard 230 or 240 products?

Whoops, I meant 220 or 230 ...

Glen

Signature · 8 lines
******************************************************************
Glen W. Mabey
[email protected]
http://mabeys.homelinux.com/glen/
******************************************************************
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#7 lore raw
In reply to Glen Mabey

Runs good on Linux and has many (perhaps too many) different extras. Performance is sufficient for most cases unless you are working with data rates of more than 30-40Mbit/s (well, IPsec with a kind of strong encryption goes only with some 3-5 megabits...). You may want to check out the site after a while - more HW products to come soon.

You might also want to check out the manufacturer's routing software based on Linux kernel with some proprietary extensions (like wireless driver that is undoubtedly better than the anything else for Atheros cards).

(don't look on my e-mail address :)

Feel free to ask me more on these products.

Dmitry

Quoted 6 lines · Glen Mabey
Quoted 1 line · glen

Alfie, have you used the Routerboard 230 or 240 products?

Whoops, I meant 220 or 230 ...

Glen

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#8 lore raw
In reply to Glen Mabey

You could try the following:
1. http://www.axiomtech.com.tw
2. http://www.soekris.com
3. http://www.pcengines.com
4. http://www.nexedi.org
5. http://www.nagasaki.com.tw
6. http://www.iei.com.tw
7. http://www.advantech.com
8. http://www.lannerinc.com

An a lot more. Nagasaki is good and has a few good options. Cheapest of the lot. Most of these are Taiwanese/Chinese companies with US offices.

Warm regards
Mohan

Quoted 26 lines

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Glen Mabey
Sent: Sunday, July 11, 2004 4:22 AM
To: LARTC Mailing List
Subject: Re: [LARTC] the "cisco vs. Linux" thread

Quoted 1 line · Alfie Viechweg

Regarding building your own router/switch. You might want

to check out

Quoted 1 line

www.routerboard.com for a really reasonably priced 4 port NIC.

I had no idea this type of board existed! (forgive my excitement)

Alfie, have you used the Routerboard 230 or 240 products? Anyone else?

Could anyone else recommend other manufacturers of this type of
hardware: an embedded system board with
* a couple of NICs
* PCMCIA
* runs linux

Thanks --
Glen

Quoted 10 lines

--
******************************************************************
Glen W. Mabey
[email protected]
http://mabeys.homelinux.com/glen/
******************************************************************
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#9 lore raw
In reply to Glen Mabey
Quoted 5 lines · Glen Mabey

Could anyone else recommend other manufacturers of this type of
hardware: an embedded system board with
* a couple of NICs
* PCMCIA
* runs linux

Try Soekris or Acrosser. Both make boards that work with Linux.

http://www.soekris.com/
http://www.acrosser.com/

-James

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#10 lore raw
In reply to Glen Mabey

Hi!

Quoted 9 lines
Quoted 3 lines · Alfie Viechweg
Quoted 3 lines

Regarding building your own router/switch. You might want to check out www.routerboard.com for a
really reasonably priced 4 port NIC.

I had no idea this type of board existed! (forgive my excitement)

Quoted 8 lines

Alfie, have you used the Routerboard 230 or 240 products? Anyone else?

Could anyone else recommend other manufacturers of this type of
hardware: an embedded system board with
* a couple of NICs
* PCMCIA
* runs linux

This one, and its cheaper:

http://www.soekris.com/

you may want to check out:

http://www.netgate.com/ (good wireless stuff).

I'm trying to buy some of the soekris hardware, but still need to get some more money. :(

Quoted 5 lines

Thanks --
Glen

-- ****************************************************************** Glen W. Mabey [email protected] http://mabeys.homelinux.com/glen/ ******************************************************************

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#11 lore raw
In reply to Glen Mabey
Quoted 2 lines · Nicholas Erkert

On a side note has anyone built a linux router with dual/quad port ethernet cards (ie Intel PRO/1000 MT Quad Port Server Adapter)?

I have bulit a linux router with quad D-Link DFE-580TX nics. It works like a charm and is routing between four local LANs. But had to use kernel patch for those cards because in-kernel driver wasn't good enough.

przemol
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#12 lore raw
In reply to Glen Mabey

Hi przemolicc >@2004.07.12_09:18:07_+0200

Quoted 7 lines
Quoted 2 lines

On a side note has anyone built a linux router with dual/quad port ethernet cards (ie Intel PRO/1000 MT Quad Port Server Adapter)?

I have bulit a linux router with quad D-Link DFE-580TX nics. It works like a charm and is routing between four local LANs. But had to use kernel patch for those cards because in-kernel driver wasn't good enough.

Could you please post a link to the driver for that nic?

Signature · 16 lines
Regards
 Abraham

TODAY the Pond!
TOMORROW the World!
                -- Frogs (1972)

___________________________________________________
 Abraham vd Merwe - Frogfoot Networks CC
 1st Floor, Albion Springs, 183 Main Road, Newlands
 Phone: +27 21 689 3876 Cell: +27 82 565 4451
 Http: http://www.frogfoot.net/ Email: [email protected]

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
#13 lore raw
In reply to Glen Mabey
Quoted 11 lines · Abraham van der Merwe

Hi przemolicc >@2004.07.12_09:18:07_+0200

Quoted 7 lines
Quoted 2 lines

On a side note has anyone built a linux router with dual/quad port ethernet cards (ie Intel PRO/1000 MT Quad Port Server Adapter)?

I have bulit a linux router with quad D-Link DFE-580TX nics. It works like a charm and is routing between four local LANs. But had to use kernel patch for those cards because in-kernel driver wasn't good enough.

Could you please post a link to the driver for that nic?

This is part of a header:

/* These identify the driver base version and may not be removed. */
static const char version1[] "sundance.c:v1.11 2/4/2003 Written by Donald Becker <[email protected]>\n"; static const char version2[] " http://www.scyld.com/network/sundance.html\n";
/* Updated to recommendations in pci-skeleton v2.12. */

przemol
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#14 lore raw
In reply to Glen Mabey
Quoted 9 lines · Abraham vd Merwe
Quoted 6 lines

This is part of a header:

/* These identify the driver base version and may not be removed. */
static const char version1[] > > "sundance.c:v1.11 2/4/2003 Written by Donald Becker <[email protected]>\n"; static const char version2[] > > " http://www.scyld.com/network/sundance.html\n";
/* Updated to recommendations in pci-skeleton v2.12. */

That looks rather outdated. The link is stale and Donald Becker hasn't worked on network drivers in ages.

I don't remember exact link. But you can look for string "sundance.c:v1.11" in google.

Please don't send me cc copy - I am on the list.

przemol
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#15 lore raw
In reply to Glen Mabey

Hi!

Quoted 9 lines
Quoted 3 lines · Alfie Viechweg
Quoted 3 lines

Regarding building your own router/switch. You might want to check out www.routerboard.com for a
really reasonably priced 4 port NIC.

I had no idea this type of board existed! (forgive my excitement)

Quoted 8 lines

Alfie, have you used the Routerboard 230 or 240 products? Anyone else?

Could anyone else recommend other manufacturers of this type of
hardware: an embedded system board with
* a couple of NICs
* PCMCIA
* runs linux

This one, and its cheaper:

http://www.soekris.com/

you may want to check out:

http://www.netgate.com/ (good wireless stuff).

I'm trying to buy some of the soekris hardware, but still need to get some more money. :(

Quoted 5 lines

Thanks --
Glen

-- ****************************************************************** Glen W. Mabey [email protected] http://mabeys.homelinux.com/glen/ ******************************************************************

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#16 lore raw
In reply to Glen Mabey
Quoted 9 lines
Quoted 7 lines

Alfie, have you used the Routerboard 230 or 240 products? Anyone else?

Could anyone else recommend other manufacturers of this type of
hardware: an embedded system board with * a couple of NICs
* PCMCIA
* runs linux

Quoted 3 lines

This one, and its cheaper:

http://www.soekris.com/

Actually, I am really interested in this kind of hardware. But it's actually not really as cheap as it looks. (Bear in mind I am based in the UK so I am looking post-shipping price)

Most of these tiny embeded devices need $20-30 or powersupply, and same again for a case, and a bit of RAM... It looks like around £300 sterling to me all in. However, you can often pickup a bottom of the range Compaq/HP server for that price... (OK, not as small and neat!)

There are some really nice and neat little boxes, which would be good for a mid-priced box where you need the grunt.

...But for low end hardware it seems hard to beat the Linksys WRT54GS which is around £50 GPB from ebuyer.... This gets you 32Mb and a 200Mhz processor! (and 2 net cards, a small switch and a wireless radio!)

The "S" model is only starting to arrive in the UK so mine's on backorder, but I think it's easily available in the US?

Ed W
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#17 lore raw
In reply to Glen Mabey
Quoted 16 lines · Ed Wildgoose
Quoted 10 lines
Quoted 7 lines

Alfie, have you used the Routerboard 230 or 240 products? Anyone else?

Could anyone else recommend other manufacturers of this type of
hardware: an embedded system board with * a couple of NICs
* PCMCIA
* runs linux

Quoted 3 lines

This one, and its cheaper:

http://www.soekris.com/

Quoted 6 lines

Actually, I am really interested in this kind of hardware. But it's actually not really as cheap as it looks. (Bear in mind I am based in the UK so I am looking post-shipping price)

Most of these tiny embeded devices need $20-30 or powersupply, and same again for a case, and a bit of RAM... It looks like around £300

No, it have RAM on board (and some of them, flash memory), the power supply is unregulated AC (read the specs), so you can buy it on your country.

Quoted 8 lines

sterling to me all in. However, you can often pickup a bottom of the range Compaq/HP server for that price... (OK, not as small and neat!)

There are some really nice and neat little boxes, which would be good for a mid-priced box where you need the grunt.
...But for low end hardware it seems hard to beat the Linksys WRT54GS which is around £50 GPB from ebuyer.... This gets you 32Mb and a 200Mhz processor! (and 2 net cards, a small switch and a wireless radio!)

I have used linksys (what a piece of crab), and I still preffer to buy a soekris card and a mini-PCI 802.11g card from netgate. I can install Linux on it, an get a very powerfull router/firewall/vpn. And due that I need it for outdoor mounting, I would buy a nema box.

Can you Install Linux/OpenBSD/FreeBSD on it?

Quoted 6 lines

The "S" model is only starting to arrive in the UK so mine's on backorder, but I think it's easily available in the US?

Ed W

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#18 lore raw
In reply to Glen Mabey

I just saw a post on the wrt54g yahoo list which was quite interesting. It's mainly a list of tiny routers, but at the bottom they list some of the other boards like those being discussed here:

http://www.seattlewireless.net/index.cgi/HardwareComparison

The main page here is where I came in. I'm interested in getting a Linksys wrt54gs first for testing. Looks like a 200Mhz processor with 32Mb ram that runs a linux distro. You can install pretty much what you want, although bear in mind it's a mips architecture.

http://www.seattlewireless.net/index.cgi/LinksysWrt54g
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#19 lore raw
In reply to Glen Mabey

I haven't tried routerboard as yet. Seem like one of the most cost effective way to add more ports to your
own switch/router/brouter device.

Another probably more complicated way is to use a USB hub, multiport USB card or the ports built into
your PC with USB ethernet devices.

The USB ethernet devices a quite expensive compared to plain ethernet - even gigabit - but if you use
an embeded board or a mico atx with a shotage of slots this a solution for getting up to a staggering
128 ethernet ports - in theory.

Wireless USB would make things even more interesting in this arena.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#20 lore raw
In reply to Glen Mabey
Quoted 4 lines

Another probably more complicated way is to use a USB hub, multiport USB card or the ports built into
your PC with USB ethernet devices.

USB 1 has a 12 Mbit bandwidth though. And you won't be able to use all of that in practice either. USB 2 is a lot higher, several hundred mbits, but again you will probably find it hard to completely saturate it.

USB drivers also tend to be nasty and flaky in my experience... Should get better in time though.

Now a motherboard with several gigabit connections in the southbridge, or perhaps even multiple PCI Express interfaces... Now you would be talking about something cheap that could knock even a top end CISCO sideways...!

Some of these new Asus P4 boards look extremely close now.

P.S. Doesn't look that hot, but no one mentioned the "open brick" yet as a possibility
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/