non hw pcm's and jackd (was: Fw: [Alsa-devel] emu10k1 device naming)
Quoted 19 lines · Florian Schmidt
Begin forwarded message:
Date: Sun, 25 Jul 2004 12:53:10 +0200
From: Florian Schmidt <[email protected]>
To: Lee Revell <[email protected]>
Cc: alsa-devel <[email protected]>, [email protected], [email protected]
Subject: Re: [Alsa-devel] emu10k1 device namingQuoted 6 lines · On Sun, 25 Jul 2004 00:29:27 -0400 Lee Revell <[email protected]> wrote:
Now that the emu10k1 driver supports low latency, multichannel capture, it would be useful to rearrange the devices. Currently you have to use hw:0,0 for playback, and hw:0,2 for capture. This works down to 32 frames (you have to record more than 2 channels to get 32 frames, because 512 bytes is the smallest period JACK supports). JACK requires the playback and capture device to be the same for both directions.
Quoted 4 lines
Actually jack supports period sizes smaller than 512 frames. I can easily start jackd with a period size of 64 frames. This is not a limitation of jackd but rather of your soundcard.
I said 512 *bytes*, not 512 frames. I should have been clearer: 512 bytes is the largest *capture* period size that JACK and the hardware both support. The hardware can go down to 384 frames, but JACK only supports power of two period sizes, so 512 *bytes* is the smallest usable capture period. If you capture 4 channels you can go down to 64 frames, 8 channels lets you go down to 32 frames.
The ALSA driver also had this wrong until I submitted a patch to fix it, because the constraints are confusingly names SND_PCM_PERIOD_SIZE (value in frames) and SND_PCM_PERIOD_BYTES (self-explanatory). Maybe the former should be changed to SND_PCM_PERIOD_FRAMES.
Quoted 17 lines
Quoted 11 lines
The current hw:0,0 device could be moved to hw:0,2. This is the best arrangement, because these are the only two devices that it makes sense to use for full-duplex. The hw:0,2 playback device is a special AC3 passthrough device, there is no capture device that corresponds to it. The same applies to the current hw:0,0 (ADC capture) and hw:0,1 (mic capture - 8000 Hz) devices, there is no corresponding playback device.
It was suggsted to use the 'asym' PCM plugin for this, but JACK does not support using a PCM as the device name, you need to give it a hardware device.
jackd also supports using non hw pcm devices. it should only spit out a warning to the user.. I just tried and besides some other weird behaviour it hardlocked my machine.. So this might be a bug that should be reported to the jack people.. But by design it should work..
Quoted 5 lines
One other thing that bothers me about jack is that it requires a ctl device by the same name as the used pcm device [which is only needed in the case of hw monitoring].. For people who don't need hw monitoring, this should not be required.. I'll write to jackit-devel about this [forwarding this mail :)]..
OK, I am also on jackit-devel, we can continue this discussion there.
I was told on this list I could put the following in my .asoundrc:
pcm.fx {
type asym
playback.pcm "hw:0,0"
capture.pcm "hw:0,2"
}then use the PCM 'pcm.fx' for JACK.
This is what happens when I try it:
rlrevell@mindpipe:~$ jackd -d alsa -d pcm.fx jackd 0.98.1 Copyright 2001-2003 Paul Davis and others. jackd comes with ABSOLUTELY NO WARRANTY This is free software, and you are welcome to redistribute it under certain conditions; see the file COPYING for details
JACK compiled with System V SHM support
loading driver ..
creating alsa driver ... pcm.fx|pcm.fx|1024|2|48000|0|0|nomon|swmeter|-|32bit ALSA lib dlmisc.c:107:(snd_dlsym_verify) unable to verify version for symbol _snd_ctl_asym_open ALSA lib control.c:629:(snd_ctl_open_conf) symbol _snd_ctl_asym_open is not defined inside (null) control open "pcm.fx" (No such device or address)
cannot load driver module alsa
Lee
-------------------------------------------------------
This SF.Net email is sponsored by BEA Weblogic Workshop FREE Java Enterprise J2EE developer tools!
Get your free copy of BEA WebLogic Workshop 8.1 today.
http://ads.osdn.com/?ad_id=4721&alloc_id=10040&op=click