Installed alsa (1.0.5)into 2.6.7 kernel:says nosoundcards
Quoted 6 lines · On Tue, 10 Aug 2004 Giuliano Pochini wrote :
Quoted 1 line · On 10 Aug 2004 06:56:28 -0000 "SailajaReddy K" <[email protected]>…
*I have installed alsa driver,lib, utilities successfully. But I couldn't see any cards in my system. Please see below outputs:
Did you check if there is something useful in the logs ?
Which logs I should check? Please suggest.
Thanks,
Sailaja
Quoted 4 lines
--
Giuliano.
Hi,.
*I have installed alsa driver,lib, utilities successfully. But I couldn't see any cards in my system. Please see below outputs:
**[root@aims-pc-100 alsa]# cat /proc/asound/cards
--- no soundcards ---
**[root@aims-pc-100 alsa]# cat /proc/asound/devices
1: : sequencer
33: : timer
**[root@aims-pc-100 alsa]# alsamixer
alsamixer: function snd_ctl_open failed for default: No such device
**[root@aims-pc-100 root]# lsmod
Module Size Used by
snd_seq_oss 35712 -
snd_seq_midi_event 7396 -
snd_seq 55824 -
snd_pcm_oss 52556 -
snd_mixer_oss 19076 -
snd_ice1712 65316 -
snd_ice17xx_ak4xxx 4004 -
snd_pcm 96736 -
snd_page_alloc 11500 -
snd_timer 25028 -
snd_ak4xxx_adda 5860 -
snd_cs8427 10660 -
snd_ac97_codec 71048 -
snd_i2c 5668 -
snd_mpu401_uart 7716 -
snd_rawmidi 24384 -
snd_seq_device 8136 -
snd 55588 -
soundcore 9152 -
autofs 16868 -
8139too 25540 -
ohci1394 34820 -
ieee1394 108976 -
parport_pc 24960 -
parport 40544 -
ehci_hcd 28900 -
usbcore 111828 -
Am I missing something?
What else I need to do and check to confirm that ALSA is working fine for my card "ICE1712 - M Audio Delta 1010"?
Pleeeeeeeeeeease help me out.
The below are the exact steps I have followed:
*Installed redhat linux 9.0 (inbuilt kernel 2.4.20-8)
*Upgraded kernel to 2.6.7, not selected for ALSA(or OSS) inclusion in kernel configuration. Selected only sound. *Downloaded alsa-driver-1.0.5a,alsa-lib-1.0.5, alsa-utils-1.0.5 and alsa-oss-1.0.5 from http://www.alsa-project.org.
*Installed alsa-driver-1.0.5a using the following:
% ./configure --with-cards=ice1712 --with-sequencer=yes && make
% make install
% ./snddevices
% chmod a+rw /dev/dsp /dev/mixer /dev/sequencer /dev/midi
*Installed alsa-lib-1.0.5 using the following:
% ./configure;make;make install
*Installed alsa-utils-1.0.5 using the following:
% ./configure;make;make install
*Installed alsa-oss-1.0.5 using the following:
% ./configure;make;make install
*modprobe snd-ice1712;modprobe snd-pcm-oss;modprobe snd-mixer-oss;modprobe snd-seq-oss
*my /etc/modules.conf
[I am not sure whether this is ok or not, please correct me if I am wrong]
alias eth0 8139too
alias usb-controller ehci-hcd
alias usb-controller1 usb-uhci
alias sound-slot-0 i810_audio
post-install sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -L >/dev/null 2>&1 || :
pre-remove sound-slot-0 /bin/aumix-minimal -f /etc/.aumixrc -S >/dev/null 2>&1 || :
# ALSA portion
alias char-major-116 snd
alias snd-card-0 snd-ice1712
# module options should go here # OSS/Free portion alias char-major-14 soundcore alias sound-slot-0 snd-card-0
# card #1 alias sound-service-0-0 snd-mixer-oss alias sound-service-0-1 snd-seq-oss alias sound-service-0-3 snd-pcm-oss alias sound-service-0-8 snd-seq-oss alias sound-service-0-12 snd-pcm-oss # OSS/Free portion - card #2 alias sound-service-1-0 snd-mixer-oss alias sound-service-1-3 snd-pcm-oss alias sound-service-1-12 snd-pcm-oss
* Is reboot needed after modifying the /etc/modules.conf file?
* I read that all mixer channels are muted by default. How exactly we should adjust the soundcards volume level?. Somebody please suggest.
Regards,
Sailaja