New: Kernel panic after getting error on inserting pcmcia card and then removing it
I'm throwing this over the wall to sysfs people (gregkh?) or maybe people who have been flidding with pci.
At a guess the complete lack of error checking in pci_alloc_child_bus() isn't helping. Wha'd'ya mean class_device_register can fail?
----- Forwarded message from [email protected] -----
Date: Wed, 22 Sep 2004 08:55:43 -0700
From: [email protected]
To: [email protected]
Subject: [Bug 3441] New: Kernel panic after getting error on inserting pcmcia card and then removing it
http://bugme.osdl.org/show_bug.cgi?id=3441
Summary: Kernel panic after getting error on inserting pcmcia
card and then removing it
Kernel Version: 2.6.8.1
Status: NEW
Severity: high
Owner: [email protected]
Submitter: [email protected]
Distribution: Debain GNU/Linux 3.1 (Sarge)
Hardware Environment:
lspci -vvv:
0000:00:00.0 Host bridge: Intel Corp. 82440MX Host Bridge (rev 01)
Subsystem: Fujitsu Limited.: Unknown device 107f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 64
0000:00:00.1 Multimedia audio controller: Intel Corp. 82440MX AC'97 Audio Controller
Subsystem: Fujitsu Limited. QSound_SigmaTel Stac97 PCI Audio
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at 1000 [size=256]
Region 1: I/O ports at 1400 [size=64]0000:00:07.0 Bridge: Intel Corp. 82440MX ISA Bridge (rev 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:07.1 IDE interface: Intel Corp. 82440MX EIDE Controller (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at 1480 [size=16]0000:00:07.2 USB Controller: Intel Corp. 82440MX USB Universal Host Controller (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at 14a0 [size=32]0000:00:07.3 Bridge: Intel Corp. 82440MX Power Management Controller
Control: I/O+ Mem+ BusMaster- SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:10.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
Subsystem: Fujitsu Limited.: Unknown device 1070
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 1440 [size=64]
Region 2: Memory at fe000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:00:11.0 Communication controller: Lucent Microelectronics F-1156IV WinModem (V90, 56KFlex) (rev 01)
Subsystem: Fujitsu Limited. LB Global LT Modem
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe101000 (32-bit, non-prefetchable) [disabled]
[size=256]
Region 1: I/O ports at 1490 [disabled] [size=8]
Region 2: I/O ports at 1800 [disabled] [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mAPME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:13.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 01)
Subsystem: Fujitsu Limited.: Unknown device 10c6
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 00010000:00:14.0 VGA compatible controller: Trident Microsystems Cyber 9525 (rev 49) (prog-if 00 [VGA])
Subsystem: Fujitsu Limited. Lifebook C6155
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe800000 (32-bit, non-prefetchable) [size=4M] Region 1: Memory at fe120000 (32-bit, non-prefetchable) [size=128K] Region 2: Memory at fe400000 (32-bit, non-prefetchable) [size=4M]
Capabilities: [80] AGP version 1.0
Status: RQ=33 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans-
64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [90] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mAPME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Software Environment:
Linux lfb2131 2.6.8.1 #1 Thu Sep 9 12:37:45 CEST 2004 i686 GNU/Linux
Gnu C 3.3.4 Gnu make 3.80 binutils 2.14.90.0.7 util-linux 2.12 mount 2.12 module-init-tools 3.1-pre5 e2fsprogs 1.35 pcmcia-cs 3.2.5 PPP 2.4.2 Linux C Library 2.3.2 Dynamic linker (ldd) 2.3.2 Procps 3.2.1 Net-tools 1.60 Console-tools 0.2.3 Sh-utils 5.2.1 Modules Loaded ipv6 ds apm af_packet yenta_socket pcmcia_core edd
vsxxxaa tsdev mousedev evdev lbtouch ide_cd cdrom rtc unix
Problem Description:
After inserting my com 3crwe154g72 wlan card in the slot when yenta_socket is loaded i get the following output:
PCI: 0000:01:00.0: class 1 doesn't match header type 01. Ignoring class.
Unable to handle kernel NULL pointer dereference at virtual address
00000008
printing eip:c0191fbb
*pde = 00000000
Oops: 0000 [#1] PREEMPT Modules linked in: ipv6 ds apm af_packet yenta_socket pcmcia_core tsdev mousedev evdev lbtouch sermouse ide_cd cdrom rtc unix CPU: 0 EIP: 0060:[sysfs_add_file+27/176] Not tainted
EIP is at sysfs_add_file+0x1b/0xb0
eax: 00000000 ebx: cbc5c920 ecx: c03ed208 edx: cbc5c960
esi: cbc5c8e0 edi: 00000000 ebp: c03b51dc esp: cb4b7ebc
ds: 007b es: 007b ss: 0068
Process pccardd (pid: 822, threadinfo=cb4b6000 task=cba8f220) : Stack: cbc5c9a8 c020aee9 cbc5c960 cbc5c920 cbc5c8e0 cbfdee40 00000000 c020aa53
00000000 c03b51dc c01c69f3 cbc5c958 c03b51dc 00000000 00000000
cb11b400
00000000 00000001 00000000 c01c6c98 cbfdee40 cb11b400 00000000
00000001
Call Trace:
[class_device_add+281/304] class_device_add+0x119/0x130
[class_device_create_file+35/48] class_device_create_file+0x23/0x30
[pci_alloc_child_bus+147/224] pci_alloc_child_bus+0x93/0xe0
[pci_scan_bridge+520/592] pci_scan_bridge+0x208/0x250
[__crc_atapi_output_bytes+623555/2523336] cb_alloc+0xd6/0xe0[pcmcia_core]
[__crc_atapi_output_bytes+611238/2523336] socket_insert+0xa9/0x150
[pcmcia_core]
[__crc_atapi_output_bytes+611997/2523336]
socket_detect_change+0x60/0x90 [pcmcia_core] [__crc_atapi_output_bytes+612499/2523336] pccardd+0x1c6/0x230
[pcmcia_core]
[default_wake_function+0/32] default_wake_function+0x0/0x20
[ret_from_fork+6/20] ret_from_fork+0x6/0x14 [default_wake_function+0/32] default_wake_function+0x0/0x20 [__crc_atapi_output_bytes+612045/2523336] pccardd+0x0/0x230
[pcmcia_core]
[kernel_thread_helper+5/24] kernel_thread_helper+0x5/0x18
Sep 10 14:00:01 localhost kernel: Code: 8b 47 08 8d 48 68 ff 48 68 0f 88
a0 01 00 00 8b 45 00 89 3c
When i remove my card then i get this:
When i then remove the card from the pcmcia slot, i get the following kernel panic:
Code: Bad EIP value.
<0>Kernel panic: Fatal Exception in interrupt
In interrupt handle - net syncing
Steps to reproduce:
Insert the 3com 3crwe154g72 wlan card when yenta_socket is loaded
------- You are receiving this mail because: ------- You are the assignee for the bug, or are watching the assignee.
----- End forwarded message -----
Signature · 4 lines
Russell King
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 PCMCIA - http://pcmcia.arm.linux.org.uk/
2.6 Serial core