Skip to contentSkip to conversation

ERROR: Disabling IRQ #11

DISCUSSION Kahro Raie 4 participants 4 messages Oct 29, 2004

lore
Share & tools
lore

Kahro Raie

author
#0 lore raw

Description:
After my system has been up for about 10 minutes I allways get the following 2 line error message on every console:
Message from syslogd@etna at Fri Oct 29 08:46:55 2004 ...
etna kernel: Disabling IRQ #11

Keywords:
kernel irq 11 usb_hcd_irq usbcore

Kernel version:
Linux version 2.6.8-1-686 ([email protected]) (gcc version 3.3.4 (Debian 1:3.3.4-13)) #1 Thu Oct 7 03:15:25 EDT 2004

My system:
Debian GNU/Linux (testing)

Other notes:
I think that the dmesg info is the most relevant and descriptive as it contains a block that appares when the error is reported:
irq 11: nobody cared!

 [<c010841a>] __report_bad_irq+0x2a/0x90
 [<c0108510>] note_interrupt+0x70/0xb0
 [<c01087f0>] do_IRQ+0x120/0x130
 [<c0106a20>] common_interrupt+0x18/0x20
 [<c028007b>] schedule+0x38b/0x4d0
 [<c0104053>] default_idle+0x23/0x40
 [<c01040e4>] cpu_idle+0x34/0x40
 [<c03307b8>] start_kernel+0x1a8/0x1f0
 [<c0330380>] unknown_bootoption+0x0/0x160

handlers:
[<e029c770>] (usb_hcd_irq+0x0/0x70 [usbcore])
[<e029c770>] (usb_hcd_irq+0x0/0x70 [usbcore])
Disabling IRQ #11

I don't need a replay for my mail, I just want to report that the bug still excists on my system and hope my info helps.

-----------------------------------------
ITV - Sinu lemmiksaated internetis!
http://www.itv.ee

#1 lore raw
Quoted 5 lines · Kahro Raie

Description:
After my system has been up for about 10 minutes I allways get the following 2 line error message on every console:

irq 11: nobody cared!

...

Quoted 1 line

Disabling IRQ #11

APIC error on CPU0: 00(01)

Hmmm, how did we take this interrupt with no bits set? why do we have bit 0 (send checksum error) set after we try to clear "errors"?

Did you not see this issue when running a different kernel, or do you always see this issue?

Is the board over-clocked?

-Len

#2 lore raw
Quoted 5 lines · Len Brown

APIC error on CPU0: 00(01)

Hmmm, how did we take this interrupt with no bits set? why do we have bit 0 (send checksum error) set after we try to clear "errors"?

Please have a look at the relevant local APIC specification. For the
P6-class local APIC a write of zero (or likely any value -- I don't remember) to the ESR makes the internal error status be copied to the externally visible ESR. A read of the ESR returns its contents and clears it. Thus the report is perfectly valid -- it means no uncleared error was left over before.

For the record: for the P5-class local APIC the ESR is the only error
status and it is also cleared on a read. Thus for that implementation the error codes reported would be reversed. Writes to the ESR have no effect by definition. Unfortunately, a range of chips have suffered from an erratum which makes data on writes to the ESR being actually recorded in the register. As a result, we cannot just do a sequence consisting of a write and a read -- we need to do that leading read to handle buggy chips correctly. And we do need to write zero specifically as otherwise a bogus error would be reported for them.

I don't remember what the specification for the P4-class local APIC is in
this area, or what other vendors' implementations do. The i82489DX APIC does not implement error reporting.

Frankly, I think this P5-to-P6 APIC specification change is an
unnecessary annoyance for an OS developer. And there are more caveats like this across local APIC implementations, this perhaps being the least harmful one.

Maciej

#3 lore raw
In reply to Kahro Raie
Quoted 6 lines · Kahro Raie

Description:
After my system has been up for about 10 minutes I allways get the following 2 line error message on every console:
Message from syslogd@etna at Fri Oct 29 08:46:55 2004 ... etna kernel: Disabling IRQ #11

Find the driver (module) that is using IRQ11. That module is probably not returning the correct value from its ISR. That's one of the changes in new kernels. ISRs now have to return values.

Cheers,
Dick Johnson
Penguin : Linux version 2.6.9 on an i686 machine (5537.79 BogoMips).
Notice : All mail here is now cached for review by John Ashcroft.
98.36% of all statistics are fiction.