2.6.10-rc1: drivers/ide/ide-dma.o: value of -130 too large for field of 1 bytes at 911
With the attached .config, I'm getting this while compiling...
[...]
CC drivers/ide/pci/sis5513.o CC drivers/ide/pci/via82cxxx.o CC drivers/ide/pci/generic.o LD drivers/ide/pci/built-in.o CC drivers/ide/ide.o CC drivers/ide/ide-default.o CC drivers/ide/ide-io.o CC drivers/ide/ide-iops.o CC drivers/ide/ide-lib.o CC drivers/ide/ide-probe.o CC drivers/ide/ide-taskfile.o CC drivers/ide/setup-pci.o CC drivers/ide/ide-dma.o
{standard input}: Assembler messages:
{standard input}:607: Error: value of -130 too large for field of 1 bytes at 911 make[3]: *** [drivers/ide/ide-dma.o] Error 1
make[2]: *** [drivers/ide] Error 2
make[1]: *** [drivers] Error 2
make: *** [bzImage] Error 2
I got the same error with 2.6.9 too.
GCC 3.2.2 and 3.4.1.
Has this been fixed since 2.6.10-rc1? Searching my Linux-Kernel folder didn't find a match.
-Paul
Quoted 11 lines · Paul Dickson
With the attached .config, I'm getting this while compiling...
...
CCdrivers/ide/ide-dma.o
{standard input}: Assembler messages:
{standard input}:607: Error: value of -130 too large for field of 1 bytes at 911 make[3]: *** [drivers/ide/ide-dma.o] Error 1
make[2]: *** [drivers/ide] Error 2
make[1]: *** [drivers] Error 2
make: *** [bzImage] Error 2
Quoted 6 lines
I got the same error with 2.6.9 too.
GCC 3.2.2 and 3.4.1.
Has this been fixed since 2.6.10-rc1? Searching my Linux-Kernel folder didn't find a match.
I can't reproduce it with your .config in 2.6.10-rc1.
Please send the output of ./scripts/ver_linux .
Quoted 1 line
-Paul
cu
Adrian
Signature · 4 lines
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon SeedQuoted 14 lines · Adrian Bunk
Quoted 13 lines · Paul Dickson
With the attached .config, I'm getting this while compiling...
...
CCdrivers/ide/ide-dma.o
{standard input}: Assembler messages:
{standard input}:607: Error: value of -130 too large for field of 1 bytes at 911 make[3]: *** [drivers/ide/ide-dma.o] Error 1
make[2]: *** [drivers/ide] Error 2
make[1]: *** [drivers] Error 2
make: *** [bzImage] Error 2I got the same error with 2.6.9 too.
Quoted 9 lines
Quoted 4 lines
GCC 3.2.2 and 3.4.1.
Has this been fixed since 2.6.10-rc1? Searching my Linux-Kernel folder didn't find a match.
I can't reproduce it with your .config in 2.6.10-rc1.
Please send the output of
./scripts/ver_linux.
The problem does not occur if I unselect "Generic PCI bus-master DMA support".
I'm also using 0=../out.router.20041030 for an external directory:
make O=../out.router.20041030/ bzImage
Quoted 1 line
From the FC2 system:
Linux violet.pwd.internal 2.6.8-1.521 #1 Mon Aug 16 09:01:18 EDT 2004 i686 i686 i386 GNU/Linux
Gnu C 3.4.1 Gnu make 3.80 binutils 2.15.90.0.3 util-linux 2.12 mount 2.12 module-init-tools 2.4.26 e2fsprogs 1.35 reiserfsprogs line reiser4progs line pcmcia-cs 3.2.7 quota-tools 3.10. PPP 2.4.2 nfs-utils 1.0.6 Linux C Library 2.3.3 Dynamic linker (ldd) 2.3.3 Procps 3.2.0 Net-tools 1.60 Kbd 1.12 Sh-utils 5.2.1 Modules Loaded snd_pcm_oss snd_mixer_oss snd_es1968 snd_ac97_codec snd_pcm snd_page_alloc snd_timer gameport snd_mpu401_uart snd_rawmidi snd_seq_device snd soundcore nfs lockd parport_pc lp parport autofs4 ide_cs ds yenta_socket pcmcia_core sunrpc 3c59x floppy sg scsi_mod microcode vfat fat dm_mod joydev uhci_hcd ext3 jbd
Quoted 1 line
From the RH9 system:
Linux red 2.4.20-18.9 #1 Thu May 29 07:08:16 EDT 2003 i686 athlon i386 GNU/Linux
Gnu C 3.2.2 Gnu make 3.79.1 binutils 2.13.90.0.18 util-linux 2.11y mount 2.11y module-init-tools writing e2fsprogs 1.32 jfsutils 1.0.17 reiserfsprogs 2002-------------> reiser4progs line pcmcia-cs 3.1.31 quota-tools 3.06. PPP 2.4.1 isdn4k-utils 3.1pre4 nfs-utils 1.0.1 Linux C Library 2.3.2 Dynamic linker (ldd) 2.3.2 Procps 2.0.11 Net-tools 1.60 Kbd 1.08 Sh-utils 4.5.3 Modules Loaded w83781d i2c-proc i2c-viapro i2c-core parport_pc lp parport nfsd lockd sunrpc iptable_filter ip_tables autofs 3c59x loop keybdev mousedev hid input usb-uhci usbcore ext3 jbd lvm-mod
-Paul
Quoted 21 lines · Paul Dickson
Quoted 19 lines · Adrian Bunk
Quoted 17 lines · Paul Dickson
With the attached .config, I'm getting this while compiling...
...
CCdrivers/ide/ide-dma.o
{standard input}: Assembler messages:
{standard input}:607: Error: value of -130 too large for field of 1 bytes at 911 make[3]: *** [drivers/ide/ide-dma.o] Error 1
make[2]: *** [drivers/ide] Error 2
make[1]: *** [drivers] Error 2
make: *** [bzImage] Error 2I got the same error with 2.6.9 too.
GCC 3.2.2 and 3.4.1.
Has this been fixed since 2.6.10-rc1? Searching my Linux-Kernel folder didn't find a match.
Quoted 6 lines
Quoted 3 lines
I can't reproduce it with your .config in 2.6.10-rc1.
Please send the output of
./scripts/ver_linux.The problem does not occur if I unselect "Generic PCI bus-master DMA support".
That's not a surprise since in this case ide-dma.c won't be included into your kernel.
Quoted 2 lines
I'm also using 0=../out.router.20041030 for an external directory:
make O=../out.router.20041030/ bzImage
Works for me...
Quoted 4 lines
Quoted 1 line
From the FC2 system:
...
Quoted 1 line
From the RH9 system:
...
The systems seem to be different enough for ruling out a problem with a specific compiler or assembler version (in both cases, my versions are between your versions).
You don't have _any_ patches applied?
Your kernel comes directly from ftp.kernel.org (or one of it's mirrors)?
Does unsetting
General setup
Configure standard kernel features (for small systems)
Optimize for size
help?
Please do the following:
- make V=1 O=../out.router.20041030/ bzImage
- cd ../out.router.20041030/
- the first command should have given you the failed gcc command; run it with the following changes:
- replace "-c" with "-S"
- replace "ide-dma.o" with "ide-dma.s"
- send me the resulting file drivers/ide/ide-dma.s (please Cc linux-kernel)
Quoted 1 line
-Paul
cu
Adrian
Signature · 4 lines
"Is there not promise of rain?" Ling Tan asked suddenly out
of the darkness. There had been need of rain for many days.
"Only a promise," Lao Er said.
Pearl S. Buck - Dragon SeedQuoted 37 lines · Adrian Bunk
Quoted 21 lines · Paul Dickson
Quoted 19 lines · Adrian Bunk
Quoted 17 lines · Paul Dickson
With the attached .config, I'm getting this while compiling...
...
CCdrivers/ide/ide-dma.o
{standard input}: Assembler messages:
{standard input}:607: Error: value of -130 too large for field of 1 bytes at 911 make[3]: *** [drivers/ide/ide-dma.o] Error 1
make[2]: *** [drivers/ide] Error 2
make[1]: *** [drivers] Error 2
make: *** [bzImage] Error 2I got the same error with 2.6.9 too.
GCC 3.2.2 and 3.4.1.
Has this been fixed since 2.6.10-rc1? Searching my Linux-Kernel folder didn't find a match.
Quoted 6 lines
Quoted 3 lines
I can't reproduce it with your .config in 2.6.10-rc1.
Please send the output of
./scripts/ver_linux.The problem does not occur if I unselect "Generic PCI bus-master DMA support".
That's not a surprise since in this case
ide-dma.cwon't be included into your kernel.Quoted 2 lines
I'm also using 0=../out.router.20041030 for an external directory:
make O=../out.router.20041030/ bzImageWorks for me...
Quoted 8 lines
Quoted 4 lines
Quoted 1 line
From the FC2 system:
...
Quoted 1 line
From the RH9 system:
...
The systems seem to be different enough for ruling out a problem with a specific compiler or assembler version (in both cases, my versions are between your versions).
As I mentioned, this is a problem with RH9; you might not want to take this further. :-)
Quoted 2 lines
You don't have _any_ patches applied?
Your kernel comes directly from ftp.kernel.org (or one of it's mirrors)?
No patches. I downloaded 2.6.9 again last night and applied the 2.6.10-rc1 patch with ketchup-0.8.1. The downloaded 2.6.9 and my previous version created by ketchup had no differences.
I avoided a 2.6.10-rc1 problem by hand copying usr/initramfs_list to ../out.router.20041030/usr
Quoted 5 lines
Does unsetting
General setup
Configure standard kernel features (for small systems)
Optimize for size
help?
Yes, that avoided the problem too.
Quoted 9 lines
Please do the following:
- make V=1 O=../out.router.20041030/ bzImage
- cd ../out.router.20041030/
- the first command should have given you the failed gcc command; run it with the following changes:
- replace "-c" with "-S"
- replace "ide-dma.o" with "ide-dma.s"
- send me the resulting filedrivers/ide/ide-dma.s(please Cc linux-kernel)
Attached is the ide-dma.s with "Optimize for size" on.
-Paul
Quoted 14 lines · Adrian Bunk
Quoted 13 lines · Paul Dickson
With the attached .config, I'm getting this while compiling...
...
CCdrivers/ide/ide-dma.o
{standard input}: Assembler messages:
{standard input}:607: Error: value of -130 too large for field of 1 bytes at 911 make[3]: *** [drivers/ide/ide-dma.o] Error 1
make[2]: *** [drivers/ide] Error 2
make[1]: *** [drivers] Error 2
make: *** [bzImage] Error 2I got the same error with 2.6.9 too.
Quoted 8 lines
Quoted 4 lines
GCC 3.2.2 and 3.4.1.
Has this been fixed since 2.6.10-rc1? Searching my Linux-Kernel folder didn't find a match.
I can't reproduce it with your .config in 2.6.10-rc1.
Please send the output of
./scripts/ver_linux.
Apparently, it was the RH9 system that was the problem. The FC2 system does not have the problem. I was using the RH9 system for compiling because it has a 1333 MHz Athlon, while the FC2 system only has a 300 MHz PII (so I never allowed a complete compilation on that system). The RH9 system is scheduled for updating to FC3 this weekend or the next.
Thanks for the assistance.
-Paul