Port u-boot to a custom board with CPU S3C44B0X
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi,
I'm the developer of Dave/B2 u-boot port.
Serial console should work right out of the box using the settings of config/B2.h and all the stuff inside cpu/s3c44b0
(well all the code inside cpu/s3c44b0 should work, of course!! ;-)
The main spot of your port should be the customization of dave/B2/memsetup.S
Regards,
Andrea Scian
Quoted 10 lines
Date: Wed, 1 Dec 2004 14:27:35 +0800
From: =?UTF-8?B?54Gw6ImyIOi9qOi/uQ==?= <[email protected]>
Reply-To: =?UTF-8?B?54Gw6ImyIOi9qOi/uQ==?= <[email protected]>
To: u-boot-users at lists.sourceforge.net
Subject: [U-Boot-Users] Port u-boot to a custom board with CPU S3C44B0XHi all. I'm porting u-boot to a custom board with CPU S3C44B0X now. I modified
include/configs/B2.haccroding to my configurations. And I don't know how to set the u-boot's console as serial port. Thanks for your replies.
A message that is not in the archive (sent off-list or not yet received): [email protected]
Hi,
well.. there's not so much to tell about serial console that is "system dependent", there are only a few function that take care about sending chars over serial line (again you can find them in serial.c, of course!) For anything else you can take a look at the main README file or REAME.whateveryouwant inside the doc directory.
There is also a very good on-line manual inside the denx site!
After reading those docs if you need support again please ask a more specific question.
Regards,
Andrea Scian
DAVE Srl - Electronics System House
via Forniz 2/1
33080 Porcia (PN) - Italy
Telephone: +39.0434.921215
Telefax: +39.0434.591631
Freefax: +39.02.700520062
web: www.dave-tech.it
e-mail address: andrea.scian at dave-tech.it
how to reach us: http://mail.map24.com/dave
Quoted 42 lines
Hi, I'm glade to know you and thanks for your help. I'm a newbie to the embeded development area. My major job is that develope application on AIX.
According to your constructive notion, I had shift my attention to the file(dave/B2/memsetup.S). Can you tell me some detail about serail console?
Any way, I must thank you again.
Quoted 9 lines · Andrea Scian
Hi,
I'm the developer of Dave/B2 u-boot port.Serial console should work right out of the box using the settings of
config/B2.hand all the stuff inside cpu/s3c44b0
(well all the code inside cpu/s3c44b0 should work, of course!! ;-)The main spot of your port should be the customization of
dave/B2/memsetup.SQuoted 19 lines
Regards,
Andrea Scian
Quoted 12 lines
Date: Wed, 1 Dec 2004 14:27:35 +0800
From: =?UTF-8?B?54Gw6ImyIOi9qOi/uQ==?= <[email protected]>
Reply-To: =?UTF-8?B?54Gw6ImyIOi9qOi/uQ==?= <[email protected]>
To: u-boot-users at lists.sourceforge.net
Subject: [U-Boot-Users] Port u-boot to a custom board with CPU S3C44B0XHi all. I'm porting u-boot to a custom board with CPU S3C44B0X now. I modified
include/configs/B2.haccroding to my configurations. And I don't know how to set the u-boot's console as serial port. Thanks for your replies.