DVD-RW writes but doesn't read
Even I had the same problem - It wasnt reading the written dvd-r/rw .But then Once I tried closing the session after a burn(not closing disk) . Then it started to show up the files .This is on 2.6.9 . But now the dvd drive stopped reading cd's anymore ;-(
-surya
Quoted 84 lines · Norbert van Nobelen
Did you try one of the disks you have written with it in another dvdplayer yet?
If the written dvds really work, then it is clearly a miracle (-:. The first thing the drive does, is a read action to see if it has an empty disc or something like multisession. If the drive reading is so terrible, that action should fail most of the time too.
Quoted 56 lines · you
Hi Jens et al
I have a laptop DVD-RW that is working fine when burning but has endless streams of errors with any kernel I try when trying to read anything (cd/dvd audio/video/data).
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x50
ide: failed opcode was 100end_request: I/O error, dev hdc, sector 571832
Buffer I/O error on device hdc, logical block 71479If I'm persistent I can read the data off the drive but I'll probably kill the drive in the process. It doesn't matter what iosched I use but I use cfq by default. I've tried disabling dma and so on without success. Any ideas?
Con
Here is some relevant data
lspci -vvv
00:1f.1 IDE interface: Intel Corp. 82801DBM (ICH4) Ultra ATA Storage Controller (rev 03) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 1100 [size=16]
Region 5: Memory at3e000000(32-bit, non-prefetchable) [size=1K]hdparm -i
/dev/hdc
/dev/hdc:Model=MATSHITADVD-RAM UJ-820S, FwRev=1.00, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=0kB, MaxMultSect=0
(maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 *udma2AdvancedPM=no
Drive conforms to: device does not report version:Quoted 8 lines
* signifies the current active mode
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/