drivers/char/specialix.c: misc cleanups (fwd)

@@ -315,7 +315,7 @@
 
 
 /* Set the IRQ using the RTS lines that run to the PAL on the board.... */
-int sx_set_irq ( struct specialix_board *bp)
+static int sx_set_irq ( struct specialix_board *bp)
 {
 	int virq;
 	int i;

@@ -379,7 +379,7 @@
 }
 
 
-int read_cross_byte (struct specialix_board *bp, int reg, int bit)
+static int read_cross_byte (struct specialix_board *bp, int reg, int bit)
 {
 	int i;
 	int t;

@@ -878,7 +878,7 @@
  *  Routines for open & close processing.
  */
 
-void turn_ints_off (struct specialix_board *bp)
+static void turn_ints_off (struct specialix_board *bp)
 {
 	if (bp->flags & SX_BOARD_IS_PCI) {
 		/* This was intended for enabeling the interrupt on the

@@ -889,7 +889,7 @@
 	(void) sx_in_off (bp, 0); /* Turn off interrupts. */
 }
 
-void turn_ints_on (struct specialix_board *bp)
+static void turn_ints_on (struct specialix_board *bp)
 {
 	if (bp->flags & SX_BOARD_IS_PCI) {
 		/* play with the PCI chip. See comment above. */

@@ -2094,41 +2094,34 @@
 }
 
 
-#ifndef MODULE
+static int iobase[SX_NBOARD]  = {0,};
+
+static int irq [SX_NBOARD] = {0,};
+
+module_param_array(iobase, int, NULL, 0);
+module_param_array(irq, int, NULL, 0);
+
 /*
- * Called at boot time.
+ * You can setup up to 4 boards.
+ * by specifying "iobase=0xXXX,0xXXX ..." as insmod parameter.
+ * You should specify the IRQs too in that case "irq=....,...". 
  * 
- * You can specify IO base for up to SX_NBOARD cards,
- * using line "specialix=0xiobase1,0xiobase2,.." at LILO prompt.
- * Note that there will be no probing at default
- * addresses in this case.
+ * More than 4 boards in one computer is not possible, as the card can
+ * only use 4 different interrupts. 
  *
- */ 
-void specialix_setup(char *str, int * ints)
-{
-	int i;
-        
-	for (i=0;i<SX_NBOARD;i++) {
-		sx_board[i].base = 0;
-	}
-
-	for (i = 1; i <= ints[0]; i++) {
-		if (i&1)
-			sx_board[i/2].base = ints[i];
-		else
-			sx_board[i/2 -1].irq = ints[i];
-	}
-}
-#endif
-
-/* 
- * This routine must be called by kernel at boot time 
  */
 static int __init specialix_init(void)
 {
 	int i;
 	int found = 0;
 
+	if (iobase[0] || iobase[1] || iobase[2] || iobase[3]) {
+		for(i = 0; i < SX_NBOARD; i++) {
+			sx_board[i].base = iobase[i];
+			sx_board[i].irq = irq[i];
+		}
+	}
+
 	printk(KERN_INFO "sx: Specialix IO8+ driver v" VERSION ", (c) R.E.Wolff 1997/1998.\n");
 	printk(KERN_INFO "sx: derived from work (c) D.Gorodchanin 1994-1996.\n");
 #ifdef CONFIG_SPECIALIX_RTSCTS

@@ -2148,7 +2141,7 @@
 	{
 		struct pci_dev *pdev = NULL;
 
-		i=0;
+		i = 0;
 		while (i < SX_NBOARD) {
 			if (sx_board[i].flags & SX_BOARD_PRESENT) {
 				i++;

@@ -2181,38 +2174,8 @@
 
 	return 0;
 }
-
-int iobase[SX_NBOARD]  = {0,};
-
-int irq [SX_NBOARD] = {0,};
-
-module_param_array(iobase, int, NULL, 0);
-module_param_array(irq, int, NULL, 0);
-
-/*
- * You can setup up to 4 boards.
- * by specifying "iobase=0xXXX,0xXXX ..." as insmod parameter.
- * You should specify the IRQs too in that case "irq=....,...". 
- * 
- * More than 4 boards in one computer is not possible, as the card can
- * only use 4 different interrupts. 
- *
- */
-static int __init specialix_init_module(void)
-{
-	int i;
-
-	if (iobase[0] || iobase[1] || iobase[2] || iobase[3]) {
-		for(i = 0; i < SX_NBOARD; i++) {
-			sx_board[i].base = iobase[i];
-			sx_board[i].irq = irq[i];
-		}
-	}
-
-	return specialix_init();
-}
 	
-static void __exit specialix_exit_module(void)
+static void __exit specialix_exit(void)
 {
 	int i;
 	

@@ -2226,7 +2189,7 @@
 	
 }
 
-module_init(specialix_init_module);
-module_exit(specialix_exit_module);
+module_init(specialix_init);
+module_exit(specialix_exit);
 
 MODULE_LICENSE("GPL");