ide0=ata66 obsolete, but replaced by what (2.6.10)?
Ever since a few kernels ago, my dmesg output says:
Kernel command line: BOOT_IMAGE=Linux ro root=303 noapic ide0=ata66 video=vesafb:mtrr,ywrapide_setup: ide0=ata66 -- OBSOLETE OPTION, WILL BE REMOVED SOON!
OK, but what is it replaced with?
Because later on, dmesg also says:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controller
ide0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pioProbing IDE interface ide0...
hda: ST94019A, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SD-R6252, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
My question is now:
1) What replaces the boot option "ide0=ata66"?
or
2) How do I get the old bus speed back?
Signature · 4 lines
Ralf Hildebrandt (i.A. des IT-Zentrum) [email protected] Charite - Universitätsmedizin Berlin Tel. +49 (0)30-450 570-155 Gemeinsame Einrichtung von FU- und HU-Berlin Fax. +49 (0)30-450 570-962 IT-Zentrum Standort CBF send no mail to [email protected]
Hi,
Quoted 29 lines · Ralf Hildebrandt
Ever since a few kernels ago, my dmesg output says:
Kernel command line: BOOT_IMAGE=Linux ro root=303 noapic ide0=ata66 video=vesafb:mtrr,ywrap
ide_setup: ide0=ata66 -- OBSOLETE OPTION, WILL BE REMOVED SOON!OK, but what is it replaced with?
Because later on, dmesg also says:Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE3-150: IDE controller at PCI slot 0000:00:08.0
NFORCE3-150: chipset revision 165
NFORCE3-150: not 100% native mode: will probe irqs later
NFORCE3-150: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE3-150: 0000:00:08.0 (rev a5) UDMA133 controlleride0: BM-DMA at 0x2080-0x2087, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x2088-0x208f, BIOS settings: hdc:DMA, hdd:pioProbing IDE interface ide0...
hda: ST94019A, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SD-R6252, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3
Quoted 3 lines
My question is now:
1) What replaces the boot option "ide0=ata66"?
Nothing ;-), what do you need it for?
Quoted 2 lines
or
2) How do I get the old bus speed back?
What bus speed are you talking about?
"idebus=" is still there but you don't need to use it for nVidia chipsets AFAIK.
Bartlomiej