Skip to contentSkip to conversation

problems with 2.6.10

DISCUSSION [email protected] 1 participant 1 message Jan 5, 2005

lore
Share & tools
lore
#0 lore raw

Hi,
I've downloaded, configured and compiled 2.6.10 for my IBM Thinkpad A21m. I've installed quite a few kernels over the years, and while not a kernel expert, thought I understood enough to get by. Sadly when I tried to boot up the new kernel I get a few error messages which I can't figure out. Also, once the system is up my keyboard is DEAD. My only option is the power-off button! My 'base' system is Mandrake 10.0. I have been running 2.6.7 with only minor problems (hence the desire to upgrade to 2.6.10).

The error messages that I've been able to find in the log are:
(I'm including an 'expected' message to indicate roughly the context)

Jan  5 08:22:33 felix kernel: Loaded 23850 symbols 
from /boot/System.map-2.6.10.
Jan  5 08:22:33 felix kernel: Symbols match kernel version 2.6.10.
Jan  5 08:22:33 felix kernel: No module symbols loaded - kernel modules not 

enabled.

This is right at the start of the log. Not sure if this means that the symbols for the modules are not enabled, as various module-provided functions do seem to be working. I can't run lsmod to check as the keyboard is dead.

Jan  5 08:22:33 felix kernel: Mounted devfs on /dev
Jan  5 08:22:33 felix kernel: jbd: version magic '2.6.3-7mdk 586 ' should be 
'2.6.10 PENTIUMIII gcc-3.3'
Jan  5 08:22:33 felix kernel: ext3: version magic '2.6.3-7mdk 586 ' should be 

'2.6.10 PENTIUMIII gcc-3.3'

Not sure if these are significant. 2.6.3-7mdk is the original Mandrake 10.0 kernel.

Jan  5 08:22:18 felix usb: Initializing USB controller (usb-uhci):  succeeded 
Jan  5 08:22:18 felix mount: mount: fs type usbdevfs not supported by kernel 
Jan  5 08:22:18 felix usb: Mount USB filesystem failed 

This worries me - I definitely have usbdevfs marked in the config:

#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_BANDWIDTH=y
# CONFIG_USB_DYNAMIC_MINORS is not set
# CONFIG_USB_SUSPEND is not set
# CONFIG_USB_OTG is not set

Despite this, USB seems to be working OK, my mouse is USB and that was responding when X11 had come up.

Jan  5 08:22:31 felix ifplugd(eth0)[1716]: Using interface eth0 
Jan  5 08:22:31 felix ifplugd(eth0)[1716]: Failed to detect plug status of 
eth0 
Jan  5 08:22:31 felix ifplugd(eth0)[1716]: Executing 
'/etc/ifplugd/ifplugd.action eth0 up'. 
Jan  5 08:22:31 felix ifplugd(eth0)[1716]: client: xircom_tulip_cb device eth0 
does not seem to be present, delaying initialization. 
Jan  5 08:22:31 felix ifplugd(eth0)[1716]: Program execution failed, return 
value is 1. 
Jan  5 08:22:31 felix ifplugd(eth0)[1716]: Exiting. 

This is serious! If the ethernet had come up, there was a chance that I could have logged in via ssh to debug further. The ethernet comes up fine under 2.6.7

That's all the error messages that I could find. Everything else seemed to be much as normal. I can live with a few error messages at boot-up provided things continue to work, but a dead keyboard is a major setback.

After I rebooted back to 2.6.7 I checked the .config file, and checked to see what modules were around and thought I'd found something - the 'input.ko' module was missing. Checking through using 'make xconfig' I discovered that there was no option for this - it's just displayed as a heading. However, checking the .config file shows

CONFIG_INPUT=y

so I presume that the 'module' has been compiled into the kernel.

I'm not a subscriber to the lkml (too much traffic) so I'd appreciate a direct reply if anyone can help.

Many thanks

Bill

Signature · 5 lines
+-----------------------------------------------+
| Bill Purvis, thrice-retired software engineer |
| e-mail:  [email protected]                         |
| web:     bil.members.beeb.net                 |
+-----------------------------------------------+