Skip to contentSkip to conversation

cfq: depth 4 reached, tagging now on

DISCUSSION Chuck Ebbert 3 participants 3 messages Mar 4, 2005

lore
Share & tools
lore
#0 lore raw
Quoted 6 lines · Jens Axboe
Quoted 5 lines · Lee Revell

Starting around 2.6.11-rc4 I get this printk during the boot process after kjournald starts, and again if I stress the filesystem.

cfq: depth 4 reached, tagging now on

Quoted 8 lines
Quoted 3 lines

Is this printk intentional? I am sure users will wonder about it, especially because (presumably) cfq turns tagging off at some point in between, and doesn't say anything about it.

It's a one-time message. CFQ starts out assuming the drive doesn't do TCQ, if the driver depth goes beyond a defined limit (4), it will assume that the hardware can do tagged queueing and change its internal accounting accordingly.

Is that a safe assumption? ide-scsi allows 5 active commands. Trying to use
cfq with ide-scsi and a DVD-RAM on 2.6.10-ac12, I get:

        $ dd if=/dev/zero of=/dev/scd1 bs=64k count=128
        cfq: depth 4 reached, tagging now on
        hdc: DMA timeout retry
        hdc: timeout waiting for DMA
        hdc: status error: status=0x58 { DriveReady SeekComplete DataRequest }
        hdc: status error: error=0x00 { }
        hdc: drive not ready for command

Then it deadlocks trying to get the host_lock:

        SysRq : Show Regs
        
        Pid: 23, comm:            scsi_eh_1
        EIP: 0060:[<c034d9d7>] CPU: 0
        EIP is at _spin_lock_irqsave+0x17/0x20
         EFLAGS: 00000286    Not tainted  (2.6.10-ac12)
        EAX: 00000246 EBX: 00000000 ECX: d7eedb40 EDX: d7eea020
        ESI: d7eea000 EDI: d7ef8b00 EBP: d7f597a0 DS: 007b ES: 007b
        CR0: 8005003b CR2: 0030b99c CR3: 15ca1000 CR4: 000002d0
         [<c02962c5>] idescsi_end_request+0x105/0x3c0
         [<c0296580>] idescsi_expiry+0x0/0x20
         [<c0296637>] idescsi_pc_intr+0x97/0x2e0
         [<c0296580>] idescsi_expiry+0x0/0x20
         [<c02965a0>] idescsi_pc_intr+0x0/0x2e0
         [<c0263a64>] ide_intr+0xe4/0x16a
         [<c01319c0>] handle_IRQ_event+0x3b/0x7b
         [<c0131aea>] __do_IRQ+0xea/0x140
         [<c0104939>] do_IRQ+0x19/0x24
         [<c0102ee2>] common_interrupt+0x1a/0x20
         [<c026007b>] ide_register_hw+0x1b/0x21
         [<c02975ee>] idescsi_eh_abort+0xaa/0x1c4
         [<c02750ca>] scsi_try_to_abort_cmd+0x5e/0x7a
         [<c027520a>] scsi_eh_abort_cmds+0x4a/0x80
         [<c034c6f4>] __down_interruptible+0xf4/0x120
         [<c0275e00>] scsi_unjam_host+0x9f/0xbf
         [<c0115385>] complete+0x45/0x60
         [<c0275ed0>] scsi_error_handler+0xb0/0xe0
         [<c0275e20>] scsi_error_handler+0x0/0xe0
         [<c01007d5>] kernel_thread_helper+0x5/0x10

ide-cd works fine with the same hardware, except for stunningly slow UDF write speed (~30K/sec; ext2 is about 350K/sec.) At least there is no UDF file corruption like others have reported.

Linux version 2.6.10-ac12 (*****) (gcc version 3.3.2 20031022 (Red Hat Linux 3.3.2-1)) #1 SMP Sat Feb 19 19:49:33 EST 2005
OEM ID: DELL Product ID: OPTIPLEXGX2 APIC at: 0xFEE00000
Processor #0 6:3 APIC version 17
Processor #1 6:3 APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
PIIX3: IDE controller at PCI slot 0000:00:0d.1
hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HL-DT-ST Model: DVDRAM GSA-4163B Rev: A100
Type: CD-ROM ANSI SCSI revision: 02
sr1: scsi3-mmc drive: 40x/40x writer dvd-ram cd/rw xa/form2 cdda tray
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 5

--
Chuck

#1 lore raw
Quoted 17 lines · Chuck Ebbert
Quoted 6 lines · Jens Axboe
Quoted 5 lines · Lee Revell

Starting around 2.6.11-rc4 I get this printk during the boot process after kjournald starts, and again if I stress the filesystem.

cfq: depth 4 reached, tagging now on

Quoted 8 lines
Quoted 3 lines

Is this printk intentional? I am sure users will wonder about it, especially because (presumably) cfq turns tagging off at some point in between, and doesn't say anything about it.

It's a one-time message. CFQ starts out assuming the drive doesn't do TCQ, if the driver depth goes beyond a defined limit (4), it will assume that the hardware can do tagged queueing and change its internal accounting accordingly.

Quoted 6 lines

Is that a safe assumption? ide-scsi allows 5 active commands. Trying to use cfq with ide-scsi and a DVD-RAM on 2.6.10-ac12, I get:

        $ dd if=/dev/zero of=/dev/scd1 bs=64k count=128
        cfq: depth 4 reached, tagging now on

It's pretty pointless to queue requests internally, if your hardware cannot do queueing. The drive is deliberately stealing information away from the io scheduler and preventing merging, etc.

What CFQ tells you is that it considers the rq timing unreliable, because it doesn't know how much time the hardware will use to complete that specific request.

Quoted 5 lines

hdc: DMA timeout retry
hdc: timeout waiting for DMA
hdc: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: status error: error=0x00 { }
hdc: drive not ready for command

Unrelated to the io scheduling, it's a drive/driver problem.

Quoted 23 lines

Then it deadlocks trying to get the host_lock:

        SysRq : Show Regs
        
        Pid: 23, comm:            scsi_eh_1
        EIP: 0060:[<c034d9d7>] CPU: 0
        EIP is at _spin_lock_irqsave+0x17/0x20
         EFLAGS: 00000286    Not tainted  (2.6.10-ac12)
        EAX: 00000246 EBX: 00000000 ECX: d7eedb40 EDX: d7eea020
        ESI: d7eea000 EDI: d7ef8b00 EBP: d7f597a0 DS: 007b ES: 007b
        CR0: 8005003b CR2: 0030b99c CR3: 15ca1000 CR4: 000002d0
         [<c02962c5>] idescsi_end_request+0x105/0x3c0
         [<c0296580>] idescsi_expiry+0x0/0x20
         [<c0296637>] idescsi_pc_intr+0x97/0x2e0
         [<c0296580>] idescsi_expiry+0x0/0x20
         [<c02965a0>] idescsi_pc_intr+0x0/0x2e0
         [<c0263a64>] ide_intr+0xe4/0x16a
         [<c01319c0>] handle_IRQ_event+0x3b/0x7b
         [<c0131aea>] __do_IRQ+0xea/0x140
         [<c0104939>] do_IRQ+0x19/0x24
         [<c0102ee2>] common_interrupt+0x1a/0x20
         [<c026007b>] ide_register_hw+0x1b/0x21
         [<c02975ee>] idescsi_eh_abort+0xaa/0x1c4
Quoted 8 lines
         [<c02750ca>] scsi_try_to_abort_cmd+0x5e/0x7a
         [<c027520a>] scsi_eh_abort_cmds+0x4a/0x80
         [<c034c6f4>] __down_interruptible+0xf4/0x120
         [<c0275e00>] scsi_unjam_host+0x9f/0xbf
         [<c0115385>] complete+0x45/0x60
         [<c0275ed0>] scsi_error_handler+0xb0/0xe0
         [<c0275e20>] scsi_error_handler+0x0/0xe0
         [<c01007d5>] kernel_thread_helper+0x5/0x10

ide-scsi error handling is broken.

Signature · 1 line
Jens Axboe
#2 lore raw
Quoted 6 lines · Jens Axboe
Quoted 5 lines · Chuck Ebbert
Quoted 3 lines · Jens Axboe
Quoted 2 lines · Lee Revell

Starting around 2.6.11-rc4 I get this printk during the boot process after kjournald starts, and again if I stress the filesystem.

Whoever dropped me from the cc: list, please don't do that. Thanks.

Lee