2.6.11-rc4: Alps touchpad too slow
Subsystems (2)
My Vaio r505te comes up with an unusably slow touchpad if I allow the ALPS driver to drive it. It says
Quoted 3 lines
ALPS Touchpad (Glidepoint) detected
Disabling hardware tapping
input: AlpsPS/2 ALPS TouchPad on isa0060/serio1
and then the trackpad operates at about 1/8 the speed I've gotten used to.
I'm running 2.6.11-rc4; this started happening somewhere between 2.6.10 and 2.6.11-rc3.
I've toyed with 'xset m', but nothing I've done there seems to have any effect. (I suspect that Linux never generates the appropriate sequence of mouse events to trigger the X cursor acceleration regime.)
I can restore the original behavior by passing "proto=exps" to psmouse.o, in which case I get
Quoted 1 line
input: PS/2 Generic Mouse on isa0060/serio1
On a related note, how are users supposed to control this newfangled PS2 driver? I'd like at least the *option* to turn tapping back on, but I can't find any knobs *anywhere*. And of course I'd like to adjust the tracking speed, too.
-andy
Quoted 17 lines · Andy Isaacson
My Vaio r505te comes up with an unusably slow touchpad if I allow the ALPS driver to drive it. It says
Quoted 3 lines
ALPS Touchpad (Glidepoint) detected
Disabling hardware tapping
input: AlpsPS/2 ALPS TouchPad on isa0060/serio1and then the trackpad operates at about 1/8 the speed I've gotten used to.
I'm running 2.6.11-rc4; this started happening somewhere between 2.6.10 and 2.6.11-rc3.
I've toyed with 'xset m', but nothing I've done there seems to have any effect. (I suspect that Linux never generates the appropriate sequence of mouse events to trigger the X cursor acceleration regime.)
Quoted 8 lines
I can restore the original behavior by passing "proto=exps" to psmouse.o, in which case I get
Quoted 1 line
input: PS/2 Generic Mouse on isa0060/serio1
On a related note, how are users supposed to control this newfangled PS2 driver? I'd like at least the *option* to turn tapping back on, but I can't find any knobs *anywhere*. And of course I'd like to adjust the tracking speed, too.
You can install the synaptics X driver
http://web.telia.com/~u89404340/touchpad/
Which has all the knobs available and works with ALPSes too.
Signature · 2 lines
Vojtech Pavlik SuSE Labs, SuSE CR
Quoted 18 lines · Andy Isaacson
My Vaio r505te comes up with an unusably slow touchpad if I allow the ALPS driver to drive it. It says
Quoted 3 lines
ALPS Touchpad (Glidepoint) detected
Disabling hardware tapping
input: AlpsPS/2 ALPS TouchPad on isa0060/serio1and then the trackpad operates at about 1/8 the speed I've gotten used to.
I'm running 2.6.11-rc4; this started happening somewhere between 2.6.10 and 2.6.11-rc3.
I've toyed with 'xset m', but nothing I've done there seems to have any effect. (I suspect that Linux never generates the appropriate sequence of mouse events to trigger the X cursor acceleration regime.)
Quoted 9 lines
I can restore the original behavior by passing "proto=exps" to psmouse.o, in which case I get
Quoted 1 line
input: PS/2 Generic Mouse on isa0060/serio1
On a related note, how are users supposed to control this newfangled PS2 driver? I'd like at least the *option* to turn tapping back on, but I can't find any knobs *anywhere*. And of course I'd like to adjust the tracking speed, too.
Andy, could you please test 2.6.12-rc1 and let us know which problems remain?
Thanks.
Quoted 8 lines · Andrew Morton
Quoted 7 lines · Andy Isaacson
My Vaio r505te comes up with an unusably slow touchpad if I allow the ALPS driver to drive it. It says
Quoted 3 lines
ALPS Touchpad (Glidepoint) detected
Disabling hardware tapping
input: AlpsPS/2 ALPS TouchPad on isa0060/serio1
Quoted 5 lines
Quoted 2 lines
and then the trackpad operates at about 1/8 the speed I've gotten used to. ... 2.6.11-rc4 ...
Andy, could you please test 2.6.12-rc1 and let us know which problems remain?
With cvsbk rev 423b66b6oJOGN68OhmSrBFxxLOtIEA (rsynced Monday, it claims to be "2.6.12-rc1"), the situation is much improved. The AlpsPS/2 driver recognizes the trackpad, tracking speed is back to normal, and tapping is turned on by default. (Drat, now I need to figure out how to turn that off again.)
The kernel output is a bit odd, though:
[ 1200.254707] Adding 987988k swap on /dev/hda3. Priority:-1 extents:1 [ 1200.330453] EXT3 FS on hda2, internal journal [ 1203.504154] SCSI subsystem initialized [ 1204.039053] Enabling hardware tapping [ 1204.099034] ieee1394: Initialized config rom entry `ip1394' [ 1204.266077] input: PS/2 Mouse on isa0060/serio1 [ 1204.400583] input: AlpsPS/2 ALPS GlidePoint on isa0060/serio1 [ 1204.779799] sbp2: $Rev: 1219 $ Ben Collins <[email protected]> [ 1206.183165] kjournald starting. Commit interval 5 seconds
Note how the "Enabling hardware tapping" message is several lines earlier than it seems it should be... I don't think I'm supposed to be tapping on my SCSI hardware.
... ah, I think I'm missing the "ALPS GlidePoint detected" message which I used to get. Without it, the "Enabling hardware tapping" message is a bit opaque.
Other than that, I have no complaints about the trackpad.
Thanks for the ping.
-andy
Quoted 13 lines · Andy Isaacson
Quoted 11 lines · Andrew Morton
Quoted 9 lines · Andy Isaacson
My Vaio r505te comes up with an unusably slow touchpad if I allow the ALPS driver to drive it. It says
Quoted 3 lines
ALPS Touchpad (Glidepoint) detected
Disabling hardware tapping
input: AlpsPS/2 ALPS TouchPad on isa0060/serio1and then the trackpad operates at about 1/8 the speed I've gotten used to. ... 2.6.11-rc4 ...
Quoted 8 lines
Quoted 2 lines
Andy, could you please test 2.6.12-rc1 and let us know which problems remain?
With cvsbk rev 423b66b6oJOGN68OhmSrBFxxLOtIEA (rsynced Monday, it claims to be "2.6.12-rc1"), the situation is much improved. The AlpsPS/2 driver recognizes the trackpad, tracking speed is back to normal, and tapping is turned on by default. (Drat, now I need to figure out how to turn that off again.)
Wonderful, thanks.
Quoted 12 lines
The kernel output is a bit odd, though:
[ 1200.254707] Adding 987988k swap on /dev/hda3. Priority:-1 extents:1 [ 1200.330453] EXT3 FS on hda2, internal journal [ 1203.504154] SCSI subsystem initialized [ 1204.039053] Enabling hardware tapping [ 1204.099034] ieee1394: Initialized config rom entry `ip1394' [ 1204.266077] input: PS/2 Mouse on isa0060/serio1 [ 1204.400583] input: AlpsPS/2 ALPS GlidePoint on isa0060/serio1 [ 1204.779799] sbp2: $Rev: 1219 $ Ben Collins <[email protected]> [ 1206.183165] kjournald starting. Commit interval 5 seconds
Quoted 7 lines
Note how the "Enabling hardware tapping" message is several lines earlier than it seems it should be... I don't think I'm supposed to be tapping on my SCSI hardware.
... ah, I think I'm missing the "ALPS GlidePoint detected" message which I used to get. Without it, the "Enabling hardware tapping" message is a bit opaque.
Yes, alps_init() had a printk removed and now the output looks funny.
drivers/input/mouse/alps.c renamed from drivers/input/mouse/alps.c~alps-printk-tidy +1 -1
@@ -395,7 +395,7 @@ int alps_init(struct psmouse *psmouse) }if (param[0 ] &0x04 ) { -printk (KERN_INFO " Enabling hardware tapping\n" ); +printk (KERN_INFO "alps.c: Enabling hardware tapping\n" );if (alps_tap_mode (psmouse,1 ))printk (KERN_WARNING "alps.c: Failed to enable hardware tapping\n" ); }
_
Quoted 5 lines · Andrew Morton
Quoted 5 lines
With cvsbk rev 423b66b6oJOGN68OhmSrBFxxLOtIEA (rsynced Monday, it claims to be "2.6.12-rc1"), the situation is much improved. The AlpsPS/2 driver recognizes the trackpad, tracking speed is back to normal, and tapping is turned on by default. (Drat, now I need to figure out how to turn that off again.)
Setting "MaxTapTime" in XF86Config if you're using the Synaptics X driver, or mousedev.maxtaptime=0 if you are using /dev/input.mice, to 0 should work.
Quoted 18 lines
Wonderful, thanks.
Quoted 16 lines
The kernel output is a bit odd, though:
[ 1200.254707] Adding 987988k swap on /dev/hda3. Priority:-1 extents:1 [ 1200.330453] EXT3 FS on hda2, internal journal [ 1203.504154] SCSI subsystem initialized [ 1204.039053] Enabling hardware tapping [ 1204.099034] ieee1394: Initialized config rom entry `ip1394' [ 1204.266077] input: PS/2 Mouse on isa0060/serio1 [ 1204.400583] input: AlpsPS/2 ALPS GlidePoint on isa0060/serio1 [ 1204.779799] sbp2: $Rev: 1219 $ Ben Collins <[email protected]> [ 1206.183165] kjournald starting. Commit interval 5 secondsNote how the "Enabling hardware tapping" message is several lines earlier than it seems it should be... I don't think I'm supposed to be tapping on my SCSI hardware.
Quoted 5 lines
Quoted 3 lines
... ah, I think I'm missing the "ALPS GlidePoint detected" message which I used to get. Without it, the "Enabling hardware tapping" message is a bit opaque.
Yes,
alps_init()had a printk removed and now the output looks funny.
I think just removing the message is better.
Quoted 13 lines
diff -puN
drivers/input/mouse/alps.c~alps-printk-tidydrivers/input/mouse/alps.cdrivers/input/mouse/alps.c renamed from drivers/input/mouse/alps.c~alps-printk-tidy +1
-1@@ -395,7 +395,7 @@ int alps_init(struct psmouse *psmouse) }if (param[0 ] &0x04 ) { -printk (KERN_INFO " Enabling hardware tapping\n" ); +printk (KERN_INFO "alps.c: Enabling hardware tapping\n" );if (alps_tap_mode (psmouse,1 ))printk (KERN_WARNING "alps.c: Failed to enable hardware tapping\n" ); }_
Signature · 2 lines
Vojtech Pavlik SuSE Labs, SuSE CR
Quoted 11 lines · Vojtech Pavlik
Quoted 5 lines · Andrew Morton
Quoted 5 lines
With cvsbk rev 423b66b6oJOGN68OhmSrBFxxLOtIEA (rsynced Monday, it claims to be "2.6.12-rc1"), the situation is much improved. The AlpsPS/2 driver recognizes the trackpad, tracking speed is back to normal, and tapping is turned on by default. (Drat, now I need to figure out how to turn that off again.)
Setting "MaxTapTime" in XF86Config if you're using the Synaptics X driver, or mousedev.maxtaptime=0 if you are using
/dev/input.mice, to 0 should work.
Actually it is mousedev.tap_time=0
Signature · 1 line
Dmitry