PROBLEM: Radeon card displays incorrectly under the 2.6.11 version unless compiled with SMP support
Quoted 83 lines · --- Dave Airlie
Quoted 1 line · Lobiuc Andrei
1.Radeon card displays incorrectly under the
2.6.11
Quoted 4 lines
version unless compiled with SMP support. 2.After compiling and installing the 2.6.11 kernel version, my ASUS Radeon 9200SE 128 MB graphic card does not display correctly in plain VGA mode. The
same
Quoted 4 lines
card has no problem with the 2.6.10 kernel.
Regarding radeonfb, dmesg reports:
"radeonfb_pci_registerBEGIN
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16(level,
Quoted 2 lines
low) -> IRQ 169
radeonfb (0000:01:00.0): Found 131072k of DDR 64bits
Quoted 16 lines
wide videoram
radeonfb (0000:01:00.0): mapped 16384k videoram
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12)
Memory=200.00 Mhz, System=166.00 MHz
radeonfb: PLL min 20000 max 40000
1 chips in connector info
- chip 1 has 1 connectors
* connector 0 of type 2 (CRT) : 2300
Starting monitor auto detection...
radeonfb: I2C (port 1) ... not found
radeonfb: I2C (port 2) ... not found
radeonfb: I2C (port 3) ... found CRT display
radeonfb: I2C (port 4) ... not found
radeonfb: I2C (port 2) ... not foundQuoted 8 lines
radeonfb: I2C (port 4) ... not found
radeonfb: I2C (port 3) ... found CRT display
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
hStart = 737, hEnd = 808, hTotal = 896
vStart = 401, vEnd = 404, vTotal = 417h_total_disp=0x59006fhsync_strt_wid=
0x8802ebQuoted 1 line
v_total_disp=0x18f01a0vsync_strt_wid=
Quoted 10 lines
0x830190
pixclock = 38210
freq = 2617
freq = 2617, PLL min = 20000, PLL max = 40000ref_div= 12,ref_clk= 2700,output_freq= 20936ref_div= 12,ref_clk= 2700,output_freq= 20936
post div =0x3fb_div=0x5dppll_div_3=0x3005d
Console: switching to colour frame buffer device90x25
Quoted 15 lines
radeonfb (0000:01:00.0): ATI Radeon Yd
radeonfb_pci_registerENDkobject_registerfailed for radeonfb (-17)[<c01cf0c7>] kobject_register+0x57/0x60 [<c0262707>] bus_add_driver+0x57/0xd0 [<c0262d5f>] driver_register+0x2f/0x40 [<c01db547>] pci_create_newid_file+0x27/0x30 [<c01dba42>] pci_register_driver+0x62/0x80 [<c05b3b40>] radeonfb_old_init+0x40/0x50 [<c059c7fb>] do_initcalls+0x2b/0xc0 [<c01002c0>] init+0x0/0x110 [<c01002c0>] init+0x0/0x110 [<c01002ef>] init+0x2f/0x110 [<c010086c>] kernel_thread_helper+0x0/0x14 [<c0100871>] kernel_thread_helper+0x5/0x14Quoted 5 lines
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux agpgart interface v0.100 (c) Dave Jones
[drm] Initialized drm 1.0.0 20040925
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16(level,
Quoted 2 lines
low) -> IRQ 169
[drm] Initialized radeon 1.14.0 20050125 on minor0:
Quoted 2 lines
ATI Technologies Inc RV280[Radeon 9200 SE]"
Quoted 7 lines
It looks like you have no agpgart chipset driver loaded or if DRM is
in the kernel, the agpgart chipset driver should be to...Dave.
Meanwhile I did another compile with AGP support enabled, dmesg says now:
"radeonfb_pci_register BEGIN
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
radeonfb (0000:01:00.0): Found 131072k of DDR 64 bits wide videoram
radeonfb (0000:01:00.0): mapped 16384k videoram
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retreived PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=200.00 Mhz, System=166.00 MHz
radeonfb: PLL min 20000 max 40000
1 chips in connector info
- chip 1 has 1 connectors
* connector 0 of type 2 (CRT) : 2300
Starting monitor auto detection...
radeonfb: I2C (port 1) ... not found
radeonfb: I2C (port 2) ... not found
radeonfb: I2C (port 3) ... found CRT display
radeonfb: I2C (port 4) ... not found
radeonfb: I2C (port 2) ... not found
radeonfb: I2C (port 4) ... not found
radeonfb: I2C (port 3) ... found CRT display
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
hStart = 737, hEnd = 808, hTotal = 896
vStart = 401, vEnd = 404, vTotal = 417h_total_disp = 0x59006f hsync_strt_wid = 0x8802ebv_total_disp = 0x18f01a0 vsync_strt_wid =0x830190
pixclock = 38210
freq = 2617
freq = 2617, PLL min = 20000, PLL max = 40000 ref_div = 12, ref_clk = 2700, output_freq = 20936 ref_div = 12, ref_clk = 2700, output_freq = 20936 post div = 0x3fb_div = 0x5dppll_div_3 = 0x3005d
Console: switching to colour frame buffer device 90x25 radeonfb (0000:01:00.0): ATI Radeon Yd radeonfb_pci_register ENDkobject_register failed for radeonfb (-17)
[<c020b047>] kobject_register+0x57/0x60 [<c029c607>] bus_add_driver+0x57/0xd0 [<c029cc5f>] driver_register+0x2f/0x40 [<c02145c7>] pci_create_newid_file+0x27/0x30 [<c0214ac2>] pci_register_driver+0x62/0x80 [<c051de00>] radeonfb_old_init+0x40/0x50 [<c050e79b>] do_initcalls+0x2b/0xc0 [<c01002c0>] init+0x0/0x110 [<c01002c0>] init+0x0/0x110 [<c01002ea>] init+0x2a/0x110 [<c010086c>] kernel_thread_helper+0x0/0x14 [<c0100871>] kernel_thread_helper+0x5/0x14
vesafb: abort, cannot reserve video memory at 0xd8000000
vesafb: framebuffer at 0xd8000000, mapped to 0xe1900000, using 937k, total 16384k
vesafb: mode is 800x600x8, linelength=800, pages=31
vesafb: protected mode interface info at c000:556c
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
fb1: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (52 C)
lp: driver loaded but no devices found
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: Maximum main memory to use for agp memory:
439M
agpgart: AGP aperture is 128M @ 0xd0000000 [drm] Initialized drm 1.0.0 20040925
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized radeon 1.14.0 20050125 on minor 0:
ATI Technologies Inc RV280[Radeon 9200 SE]"
and
"agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode
[drm] Loading R200 Microcode"
but there's no improvement in displaying the text. Here are parts of the .config file used:
<.config>
#
# Automatically generated make config: don't edit # Linux kernel version: 2.6.11
# Sun Mar 6 12:04:27 2005
#CONFIG_X86=yCONFIG_MMU=yCONFIG_UID16=yCONFIG_GENERIC_ISA_DMA=y CONFIG_GENERIC_IOMAP=y
#
# Code maturity level options
#
# CONFIG_EXPERIMENTAL is not setCONFIG_CLEAN_COMPILE=yCONFIG_BROKEN_ON_SMP=yCONFIG_LOCK_KERNEL=y
#
# General setup
#CONFIG_LOCALVERSION=""CONFIG_SWAP=yCONFIG_SYSVIPC=yCONFIG_BSD_PROCESS_ACCT=y
# CONFIG_BSD_PROCESS_ACCT_V3 is not setCONFIG_SYSCTL=y
# CONFIG_AUDIT is not setCONFIG_LOG_BUF_SHIFT=14CONFIG_HOTPLUG=yCONFIG_KOBJECT_UEVENT=yCONFIG_IKCONFIG=y
# CONFIG_IKCONFIG_PROC is not setCONFIG_EMBEDDED=yCONFIG_KALLSYMS=y
# CONFIG_KALLSYMS_ALL is not set
# CONFIG_KALLSYMS_EXTRA_PASS is not setCONFIG_FUTEX=yCONFIG_EPOLL=y
# CONFIG_CC_OPTIMIZE_FOR_SIZE is not setCONFIG_SHMEM=yCONFIG_CC_ALIGN_FUNCTIONS=0CONFIG_CC_ALIGN_LABELS=0CONFIG_CC_ALIGN_LOOPS=0CONFIG_CC_ALIGN_JUMPS=0
# CONFIG_TINY_SHMEM is not set
#
# Loadable module support
#CONFIG_MODULES=yCONFIG_MODULE_UNLOAD=yCONFIG_OBSOLETE_MODPARM=y
# CONFIG_MODULE_SRCVERSION_ALL is not setCONFIG_KMOD=y
..........................
#
# Hardware configuration
#CONFIG_FT_STD_FDC=y
# CONFIG_FT_MACH2 is not set
# CONFIG_FT_PROBE_FC10 is not set
# CONFIG_FT_ALT_FDC is not setCONFIG_FT_ALPHA_CLOCK=0CONFIG_AGP=y
# CONFIG_AGP_ALI is not setCONFIG_AGP_ATI=y
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_AMD64 is not set
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_INTEL_MCH is not set
# CONFIG_AGP_NVIDIA is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_SWORKS is not setCONFIG_AGP_VIA=y
# CONFIG_AGP_EFFICEON is not setCONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not setCONFIG_DRM_RADEON=y
# CONFIG_DRM_MGA is not set
# CONFIG_DRM_SIS is not set
# CONFIG_MWAVE is not setCONFIG_RAW_DRIVER=mCONFIG_HPET=y
# CONFIG_HPET_RTC_IRQ is not setCONFIG_HPET_MMAP=yCONFIG_MAX_RAW_DEVS=256CONFIG_HANGCHECK_TIMER=m
#
# I2C support
#CONFIG_I2C=yCONFIG_I2C_CHARDEV=m
#
# I2C Algorithms
#CONFIG_I2C_ALGOBIT=yCONFIG_I2C_ALGOPCF=m
# CONFIG_I2C_ALGOPCA is not set
#
# I2C Hardware Bus support
#CONFIG_I2C_ELEKTOR=mCONFIG_I2C_PARPORT=mCONFIG_I2C_PARPORT_LIGHT=m
CONFIG_SCx200_ACB=m
# CONFIG_I2C_PCA_ISA is not set
#
# Hardware Sensors Chip support
#CONFIG_I2C_SENSOR=mCONFIG_SENSORS_LM83=mCONFIG_SENSORS_LM90=m
#
# Other I2C Chip support
#
# CONFIG_I2C_DEBUG_CORE is not set
# CONFIG_I2C_DEBUG_ALGO is not set
# CONFIG_I2C_DEBUG_BUS is not set
# CONFIG_I2C_DEBUG_CHIP is not set
........................................
#
# Graphics support
#CONFIG_FB=yCONFIG_FB_MODE_HELPERS=yCONFIG_FB_TILEBLITTING=y
# CONFIG_FB_CIRRUS is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
# CONFIG_FB_ASILIANT is not set
# CONFIG_FB_IMSTT is not setCONFIG_FB_VGA16=yCONFIG_FB_VESA=yCONFIG_VIDEO_SELECT=yCONFIG_FB_HGA=m
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not setCONFIG_FB_RADEON_OLD=yCONFIG_FB_RADEON=yCONFIG_FB_RADEON_I2C=yCONFIG_FB_RADEON_DEBUG=y
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_KYRO is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not setCONFIG_FB_VIRTUAL=m
#
# Console display driver support
#CONFIG_VGA_CONSOLE=yCONFIG_MDA_CONSOLE=mCONFIG_DUMMY_CONSOLE=yCONFIG_FRAMEBUFFER_CONSOLE=yCONFIG_FONTS=y
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
CONFIG_FONT_6x11=y
CONFIG_FONT_PEARL_8x8=y
CONFIG_FONT_ACORN_8x8=y
CONFIG_FONT_MINI_4x6=y
CONFIG_FONT_SUN8x16=y
CONFIG_FONT_SUN12x22=y
</.config>
The big question is why is it working under 2.6.10? Even if I configure 2.6.11 with 'make oldconfig' using the 2.6.10 .config file brings no improvements.
Are there any patches I haven't heard of?
Thank you very much for your reply.
Regards, Andrei Lobiuc.
__________________________________
Celebrate Yahoo!'s 10th Birthday!
Yahoo! Netrospective: 100 Moments of the Web
http://birthday.yahoo.com/netrospective/