Skip to contentSkip to conversation

Serial updates

PATCH New Russell King 1 participant 1 message Jun 29, 2005

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 Serial updates

The following changes have been submitted to Linus and Andrew, as seen previously (and individually) on this mailing list.

 Documentation/serial/driver         |    4 -
 arch/parisc/configs/712_defconfig   |    2 
 arch/parisc/configs/a500_defconfig  |    2 
 arch/parisc/configs/b180_defconfig  |    2 
 arch/parisc/configs/c3000_defconfig |    2 
 arch/parisc/defconfig               |    2 
 drivers/serial/8250.c               |   33 ++++++-----
 drivers/serial/Kconfig              |    2 
 drivers/serial/au1x00_uart.c        |    3 -
 drivers/serial/ip22zilog.c          |   13 ++--
 drivers/serial/mpsc.c               |    3 -
 drivers/serial/pmac_zilog.c         |    4 -
 drivers/serial/pxa.c                |    3 -
 drivers/serial/serial_core.c        |   28 +++++++++
 drivers/serial/serial_txx9.c        |    3 -
 drivers/serial/sunsab.c             |    7 --
 drivers/serial/sunsu.c              |    3 -
 drivers/serial/sunzilog.c           |   13 ++--
 include/asm-alpha/serial.h          |   47 ----------------
 include/asm-arm26/serial.h          |   22 -------
 include/asm-i386/serial.h           |  102 ------------------------------------
 include/asm-m68k/serial.h           |   47 ----------------
 include/asm-mips/serial.h           |   84 -----------------------------
 include/asm-parisc/serial.h         |   16 -----
 include/asm-ppc/pc_serial.h         |   86 ------------------------------
 include/asm-sh/bigsur/serial.h      |    5 -
 include/asm-sh/ec3104/serial.h      |    4 -
 include/asm-sh/serial.h             |    6 --
 include/asm-sh64/serial.h           |    4 -
 include/asm-x86_64/serial.h         |  102 ------------------------------------
 30 files changed, 82 insertions(+), 572 deletions(-)

From: Russell King: Wed Jun 29 18:45:19 BST 2005

[PATCH] Serial: Split 8250 port table (part 2)

Remove legacy ISA serial ports for Accent, Boca, Fourport, Hub6 and MCA from the architecture specific serial.h include.

The only ports which remain in asm-*/serial.h are the platform specific entries. These should really be converted by platform maintainers to use a platform device, such as can be found in arch/arm/mach-footbridge/isa.c

From: Russell King: Wed Jun 29 18:41:51 BST 2005

[PATCH] Serial: Disable OX950 transmitter for flow control

Disable the transmitter whenever we want to prevent characters being transmitted by flow control. However, if we run out of characters to send and want to only disable the TX interrupt, allow that scenario.

From: Russell King: Wed Jun 29 18:40:53 BST 2005

[PATCH] Serial: Check status of CTS when using flow control

Fix bugme #4712: read the CTS status and set hw_stopped if CTS is not active when opening the port and/or enabling CRTSCTS

Thanks to Stefan Wolff for spotting this problem.

From: Russell King: Wed Jun 29 09:42:38 BST 2005

[PATCH] Serial: Adjust serial locking

This patch changes the way serial ports are locked when getting modem status. This change is necessary because we will need to atomically read the modem status and take action depending on the CTS status.

Documentation/serial/driver (mode:100644) +2 -2
Index: Documentation/serial/driver
===================================================================
@@ -107,8 +107,8 @@
 	indicate that the signal is permanently active.  If RI is
 	not available, the signal should not be indicated as active.
 
-	Locking: none.
-	Interrupts: caller dependent.
+	Locking: port->lock taken.
+	Interrupts: locally disabled.
 	This call must not sleep
 
   stop_tx(port,tty_stop)
arch/parisc/configs/712_defconfig (mode:100644) +1 -1
Index: arch/parisc/configs/712_defconfig
===================================================================
@@ -506,7 +506,7 @@
 #
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_NR_UARTS=17
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
arch/parisc/configs/a500_defconfig (mode:100644) +1 -1
Index: arch/parisc/configs/a500_defconfig
===================================================================
@@ -662,7 +662,7 @@
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_CS=m
-CONFIG_SERIAL_8250_NR_UARTS=8
+CONFIG_SERIAL_8250_NR_UARTS=17
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
arch/parisc/configs/b180_defconfig (mode:100644) +1 -1
Index: arch/parisc/configs/b180_defconfig
===================================================================
@@ -514,7 +514,7 @@
 #
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
arch/parisc/configs/c3000_defconfig (mode:100644) +1 -1
Index: arch/parisc/configs/c3000_defconfig
===================================================================
@@ -661,7 +661,7 @@
 #
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
arch/parisc/defconfig (mode:100644) +1 -1
Index: arch/parisc/defconfig
===================================================================
@@ -517,7 +517,7 @@
 #
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_SERIAL_8250_NR_UARTS=4
+CONFIG_SERIAL_8250_NR_UARTS=13
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
drivers/serial/8250.c (mode:100644) +17 -16
Index: drivers/serial/8250.c
===================================================================
@@ -105,7 +105,7 @@
 	SERIAL_PORT_DFNS /* defined in asm/serial.h */
 };
 
-#define UART_NR	(ARRAY_SIZE(old_serial_port) + CONFIG_SERIAL_8250_NR_UARTS)
+#define UART_NR	CONFIG_SERIAL_8250_NR_UARTS
 
 #ifdef CONFIG_SERIAL_8250_RSA
 
@@ -993,21 +993,24 @@
 	up->port.irq = (irq > 0) ? irq : 0;
 }
 
+static inline void __stop_tx(struct uart_8250_port *p)
+{
+	if (p->ier & UART_IER_THRI) {
+		p->ier &= ~UART_IER_THRI;
+		serial_out(p, UART_IER, p->ier);
+	}
+}
+
 static void serial8250_stop_tx(struct uart_port *port, unsigned int tty_stop)
 {
 	struct uart_8250_port *up = (struct uart_8250_port *)port;
 
-	if (up->ier & UART_IER_THRI) {
-		up->ier &= ~UART_IER_THRI;
-		serial_out(up, UART_IER, up->ier);
-	}
+	__stop_tx(up);
 
 	/*
-	 * We only do this from uart_stop - if we run out of
-	 * characters to send, we don't want to prevent the
-	 * FIFO from emptying.
+	 * We really want to stop the transmitter from sending.
 	 */
-	if (up->port.type == PORT_16C950 && tty_stop) {
+	if (up->port.type == PORT_16C950) {
 		up->acr |= UART_ACR_TXDIS;
 		serial_icr_write(up, UART_ACR, up->acr);
 	}
@@ -1031,10 +1034,11 @@
 				transmit_chars(up);
 		}
 	}
+
 	/*
-	 * We only do this from uart_start
+	 * Re-enable the transmitter if we disabled it.
 	 */
-	if (tty_start && up->port.type == PORT_16C950) {
+	if (up->port.type == PORT_16C950 && up->acr & UART_ACR_TXDIS) {
 		up->acr &= ~UART_ACR_TXDIS;
 		serial_icr_write(up, UART_ACR, up->acr);
 	}
@@ -1155,7 +1159,7 @@
 		return;
 	}
 	if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
-		serial8250_stop_tx(&up->port, 0);
+		__stop_tx(up);
 		return;
 	}
 
@@ -1174,7 +1178,7 @@
 	DEBUG_INTR("THRE...");
 
 	if (uart_circ_empty(xmit))
-		serial8250_stop_tx(&up->port, 0);
+		__stop_tx(up);
 }
 
 static _INLINE_ void check_modem_status(struct uart_8250_port *up)
@@ -1376,13 +1380,10 @@
 static unsigned int serial8250_get_mctrl(struct uart_port *port)
 {
 	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned long flags;
 	unsigned char status;
 	unsigned int ret;
 
-	spin_lock_irqsave(&up->port.lock, flags);
 	status = serial_in(up, UART_MSR);
-	spin_unlock_irqrestore(&up->port.lock, flags);
 
 	ret = 0;
 	if (status & UART_MSR_DCD)
drivers/serial/Kconfig (mode:100644) +1 -1
Index: drivers/serial/Kconfig
===================================================================
@@ -86,7 +86,7 @@
 	  namespace, say Y here.  If unsure, say N.
 
 config SERIAL_8250_NR_UARTS
-	int "Maximum number of non-legacy 8250/16550 serial ports"
+	int "Maximum number of 8250/16550 serial ports"
 	depends on SERIAL_8250
 	default "4"
 	help
drivers/serial/au1x00_uart.c (mode:100644) +0 -3
Index: drivers/serial/au1x00_uart.c
===================================================================
@@ -556,13 +556,10 @@
 static unsigned int serial8250_get_mctrl(struct uart_port *port)
 {
 	struct uart_8250_port *up = (struct uart_8250_port *)port;
-	unsigned long flags;
 	unsigned char status;
 	unsigned int ret;
 
-	spin_lock_irqsave(&up->port.lock, flags);
 	status = serial_in(up, UART_MSR);
-	spin_unlock_irqrestore(&up->port.lock, flags);
 
 	ret = 0;
 	if (status & UART_MSR_DCD)
drivers/serial/ip22zilog.c (mode:100644) +7 -6
Index: drivers/serial/ip22zilog.c
===================================================================
@@ -518,27 +518,28 @@
 static __inline__ unsigned char ip22zilog_read_channel_status(struct uart_port *port)
 {
 	struct zilog_channel *channel;
-	unsigned long flags;
 	unsigned char status;
 
-	spin_lock_irqsave(&port->lock, flags);
-
 	channel = ZILOG_CHANNEL_FROM_PORT(port);
 	status = readb(&channel->control);
 	ZSDELAY();
 
-	spin_unlock_irqrestore(&port->lock, flags);
-
 	return status;
 }
 
 /* The port lock is not held.  */
 static unsigned int ip22zilog_tx_empty(struct uart_port *port)
 {
+	unsigned long flags;
 	unsigned char status;
 	unsigned int ret;
 
+	spin_lock_irqsave(&port->lock, flags);
+
 	status = ip22zilog_read_channel_status(port);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
 	if (status & Tx_BUF_EMP)
 		ret = TIOCSER_TEMT;
 	else
@@ -547,7 +548,7 @@
 	return ret;
 }
 
-/* The port lock is not held.  */
+/* The port lock is held and interrupts are disabled.  */
 static unsigned int ip22zilog_get_mctrl(struct uart_port *port)
 {
 	unsigned char status;
drivers/serial/mpsc.c (mode:100644) +0 -3
Index: drivers/serial/mpsc.c
===================================================================
@@ -1058,12 +1058,9 @@
 {
 	struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
 	u32 mflags, status;
-	ulong iflags;
 
-	spin_lock_irqsave(&pi->port.lock, iflags);
 	status = (pi->mirror_regs) ? pi->MPSC_CHR_10_m :
 		readl(pi->mpsc_base + MPSC_CHR_10);
-	spin_unlock_irqrestore(&pi->port.lock, iflags);
 
 	mflags = 0;
 	if (status & 0x1)
drivers/serial/pmac_zilog.c (mode:100644) +2 -2
Index: drivers/serial/pmac_zilog.c
===================================================================
@@ -604,7 +604,7 @@
 /* 
  * Get Modem Control bits (only the input ones, the core will
  * or that with a cached value of the control ones)
- * The port lock is not held.
+ * The port lock is held and interrupts are disabled.
  */
 static unsigned int pmz_get_mctrl(struct uart_port *port)
 {
@@ -615,7 +615,7 @@
 	if (ZS_IS_ASLEEP(uap) || uap->node == NULL)
 		return 0;
 
-	status = pmz_peek_status(to_pmz(port));
+	status = read_zsreg(uap, R0);
 
 	ret = 0;
 	if (status & DCD)
drivers/serial/pxa.c (mode:100644) +0 -3
Index: drivers/serial/pxa.c
===================================================================
@@ -274,14 +274,11 @@
 static unsigned int serial_pxa_get_mctrl(struct uart_port *port)
 {
 	struct uart_pxa_port *up = (struct uart_pxa_port *)port;
-	unsigned long flags;
 	unsigned char status;
 	unsigned int ret;
 
 return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-	spin_lock_irqsave(&up->port.lock, flags);
 	status = serial_in(up, UART_MSR);
-	spin_unlock_irqrestore(&up->port.lock, flags);
 
 	ret = 0;
 	if (status & UART_MSR_DCD)
drivers/serial/serial_core.c (mode:100644) +27 -1
Index: drivers/serial/serial_core.c
===================================================================
@@ -182,6 +182,13 @@
 				uart_set_mctrl(port, TIOCM_RTS | TIOCM_DTR);
 		}
 
+		if (info->flags & UIF_CTS_FLOW) {
+			spin_lock_irq(&port->lock);
+			if (!(port->ops->get_mctrl(port) & TIOCM_CTS))
+				info->tty->hw_stopped = 1;
+			spin_unlock_irq(&port->lock);
+		}
+
 		info->flags |= UIF_INITIALIZED;
 
 		clear_bit(TTY_IO_ERROR, &info->tty->flags);
@@ -828,7 +835,10 @@
 	if ((!file || !tty_hung_up_p(file)) &&
 	    !(tty->flags & (1 << TTY_IO_ERROR))) {
 		result = port->mctrl;
+
+		spin_lock_irq(&port->lock);
 		result |= port->ops->get_mctrl(port);
+		spin_unlock_irq(&port->lock);
 	}
 	up(&state->sem);
 
@@ -1131,6 +1141,16 @@
 		spin_unlock_irqrestore(&state->port->lock, flags);
 	}
 
+	/* Handle turning on CRTSCTS */
+	if (!(old_termios->c_cflag & CRTSCTS) && (cflag & CRTSCTS)) {
+		spin_lock_irqsave(&state->port->lock, flags);
+		if (!(state->port->ops->get_mctrl(state->port) & TIOCM_CTS)) {
+			tty->hw_stopped = 1;
+			state->port->ops->stop_tx(state->port, 0);
+		}
+		spin_unlock_irqrestore(&state->port->lock, flags);
+	}
+
 #if 0
 	/*
 	 * No need to wake up processes in open wait, since they
@@ -1369,6 +1389,7 @@
 	DECLARE_WAITQUEUE(wait, current);
 	struct uart_info *info = state->info;
 	struct uart_port *port = state->port;
+	unsigned int mctrl;
 
 	info->blocked_open++;
 	state->count--;
@@ -1416,7 +1437,10 @@
 		 * and wait for the carrier to indicate that the
 		 * modem is ready for us.
 		 */
-		if (port->ops->get_mctrl(port) & TIOCM_CAR)
+		spin_lock_irq(&port->lock);
+		mctrl = port->ops->get_mctrl(port);
+		spin_unlock_irq(&port->lock);
+		if (mctrl & TIOCM_CAR)
 			break;
 
 		up(&state->sem);
@@ -1618,7 +1642,9 @@
 
 	if(capable(CAP_SYS_ADMIN))
 	{
+		spin_lock_irq(&port->lock);
 		status = port->ops->get_mctrl(port);
+		spin_unlock_irq(&port->lock);
 
 		ret += sprintf(buf + ret, " tx:%d rx:%d",
 				port->icount.tx, port->icount.rx);
drivers/serial/serial_txx9.c (mode:100644) +0 -3
Index: drivers/serial/serial_txx9.c
===================================================================
@@ -442,13 +442,10 @@
 static unsigned int serial_txx9_get_mctrl(struct uart_port *port)
 {
 	struct uart_txx9_port *up = (struct uart_txx9_port *)port;
-	unsigned long flags;
 	unsigned int ret;
 
-	spin_lock_irqsave(&up->port.lock, flags);
 	ret =  ((sio_in(up, TXX9_SIFLCR) & TXX9_SIFLCR_RTSSC) ? 0 : TIOCM_RTS)
 		| ((sio_in(up, TXX9_SICISR) & TXX9_SICISR_CTSS) ? 0 : TIOCM_CTS);
-	spin_unlock_irqrestore(&up->port.lock, flags);
 
 	return ret;
 }
drivers/serial/sunsab.c (mode:100644) +1 -6
Index: drivers/serial/sunsab.c
===================================================================
@@ -426,18 +426,15 @@
 		sunsab_tx_idle(up);
 }
 
-/* port->lock is not held.  */
+/* port->lock is held by caller and interrupts are disabled.  */
 static unsigned int sunsab_get_mctrl(struct uart_port *port)
 {
 	struct uart_sunsab_port *up = (struct uart_sunsab_port *) port;
-	unsigned long flags;
 	unsigned char val;
 	unsigned int result;
 
 	result = 0;
 
-	spin_lock_irqsave(&up->port.lock, flags);
-
 	val = readb(&up->regs->r.pvr);
 	result |= (val & up->pvr_dsr_bit) ? 0 : TIOCM_DSR;
 
@@ -447,8 +444,6 @@
 	val = readb(&up->regs->r.star);
 	result |= (val & SAB82532_STAR_CTS) ? TIOCM_CTS : 0;
 
-	spin_unlock_irqrestore(&up->port.lock, flags);
-
 	return result;
 }
 
drivers/serial/sunsu.c (mode:100644) +0 -3
Index: drivers/serial/sunsu.c
===================================================================
@@ -572,13 +572,10 @@
 static unsigned int sunsu_get_mctrl(struct uart_port *port)
 {
 	struct uart_sunsu_port *up = (struct uart_sunsu_port *) port;
-	unsigned long flags;
 	unsigned char status;
 	unsigned int ret;
 
-	spin_lock_irqsave(&up->port.lock, flags);
 	status = serial_in(up, UART_MSR);
-	spin_unlock_irqrestore(&up->port.lock, flags);
 
 	ret = 0;
 	if (status & UART_MSR_DCD)
drivers/serial/sunzilog.c (mode:100644) +7 -6
Index: drivers/serial/sunzilog.c
===================================================================
@@ -610,27 +610,28 @@
 static __inline__ unsigned char sunzilog_read_channel_status(struct uart_port *port)
 {
 	struct zilog_channel __iomem *channel;
-	unsigned long flags;
 	unsigned char status;
 
-	spin_lock_irqsave(&port->lock, flags);
-
 	channel = ZILOG_CHANNEL_FROM_PORT(port);
 	status = sbus_readb(&channel->control);
 	ZSDELAY();
 
-	spin_unlock_irqrestore(&port->lock, flags);
-
 	return status;
 }
 
 /* The port lock is not held.  */
 static unsigned int sunzilog_tx_empty(struct uart_port *port)
 {
+	unsigned long flags;
 	unsigned char status;
 	unsigned int ret;
 
+	spin_lock_irqsave(&port->lock, flags);
+
 	status = sunzilog_read_channel_status(port);
+
+	spin_unlock_irqrestore(&port->lock, flags);
+
 	if (status & Tx_BUF_EMP)
 		ret = TIOCSER_TEMT;
 	else
@@ -639,7 +640,7 @@
 	return ret;
 }
 
-/* The port lock is not held.  */
+/* The port lock is held and interrupts are disabled.  */
 static unsigned int sunzilog_get_mctrl(struct uart_port *port)
 {
 	unsigned char status;
include/asm-alpha/serial.h (mode:100644) +1 -46

55 lines not on this page · raw message

include/asm-arm26/serial.h (mode:100644) +2 -20
Index: include/asm-arm26/serial.h
===================================================================
@@ -30,34 +30,16 @@
 #if defined(CONFIG_ARCH_A5K)
      /* UART CLK        PORT  IRQ     FLAGS        */
 
-#define STD_SERIAL_PORT_DEFNS                                           \
+#define SERIAL_PORT_DFNS                                                \
         { 0, BASE_BAUD, 0x3F8, 10, STD_COM_FLAGS },     /* ttyS0 */     \
         { 0, BASE_BAUD, 0x2F8, 10, STD_COM_FLAGS },     /* ttyS1 */
 
 #else
 
-#define STD_SERIAL_PORT_DEFNS                                           \
+#define SERIAL_PORT_DFNS                                                \
         { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS0 */     \
         { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS1 */
 
 #endif
 
-#define EXTRA_SERIAL_PORT_DEFNS \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS2 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS3 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS4 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS5 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS6 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS7 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS8 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS9 */     \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS10 */    \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS11 */    \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS12 */    \
-        { 0, BASE_BAUD, 0    ,  0, STD_COM_FLAGS },     /* ttyS13 */
-
-#define SERIAL_PORT_DFNS		\
-	STD_SERIAL_PORT_DEFNS		\
-	EXTRA_SERIAL_PORT_DEFNS
-
 #endif
include/asm-i386/serial.h (mode:100644) +1 -101

110 lines not on this page · raw message

include/asm-m68k/serial.h (mode:100644) +1 -46

55 lines not on this page · raw message

include/asm-mips/serial.h (mode:100644) +0 -84

106 lines not on this page · raw message

include/asm-parisc/serial.h (mode:100644) +1 -15
Index: include/asm-parisc/serial.h
===================================================================
@@ -19,18 +19,4 @@
  * A500 w/ PCI serial cards: 5 + 4 * card ~= 17
  */
  
-#define STD_SERIAL_PORT_DEFNS			\
-	{ 0, },		/* ttyS0 */	\
-	{ 0, },		/* ttyS1 */	\
-	{ 0, },		/* ttyS2 */	\
-	{ 0, },		/* ttyS3 */	\
-	{ 0, },		/* ttyS4 */	\
-	{ 0, },		/* ttyS5 */	\
-	{ 0, },		/* ttyS6 */	\
-	{ 0, },		/* ttyS7 */	\
-	{ 0, },		/* ttyS8 */
-
-
-#define SERIAL_PORT_DFNS		\
-	STD_SERIAL_PORT_DEFNS
-
+#define SERIAL_PORT_DFNS
include/asm-ppc/pc_serial.h (mode:100644) +1 -85

94 lines not on this page · raw message

include/asm-sh/bigsur/serial.h (mode:100644) +1 -4
Index: include/asm-sh/bigsur/serial.h
===================================================================
@@ -14,13 +14,10 @@
 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
 
 
-#define STD_SERIAL_PORT_DEFNS                   \
+#define SERIAL_PORT_DFNS                   \
         /* UART CLK   PORT IRQ     FLAGS        */                      \
         { 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS } /* ttyS0 */ 
 
-
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
 /* XXX: This should be moved ino irq.h */
 #define irq_cannonicalize(x) (x)
 
include/asm-sh/ec3104/serial.h (mode:100644) +1 -3
Index: include/asm-sh/ec3104/serial.h
===================================================================
@@ -10,13 +10,11 @@
  * it's got the keyboard controller behind it so we can't really use it
  * (without moving the keyboard driver to userspace, which doesn't sound
  * like a very good idea) */
-#define STD_SERIAL_PORT_DEFNS			\
+#define SERIAL_PORT_DFNS			\
 	/* UART CLK   PORT IRQ     FLAGS        */			\
 	{ 0, BASE_BAUD, 0x11C00, EC3104_IRQBASE+7, STD_COM_FLAGS }, /* ttyS0 */	\
 	{ 0, BASE_BAUD, 0x12000, EC3104_IRQBASE+8, STD_COM_FLAGS }, /* ttyS1 */	\
 	{ 0, BASE_BAUD, 0x12400, EC3104_IRQBASE+9, STD_COM_FLAGS }, /* ttyS2 */
 
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
 /* XXX: This should be moved ino irq.h */
 #define irq_cannonicalize(x) (x)
include/asm-sh/serial.h (mode:100644) +2 -4
Index: include/asm-sh/serial.h
===================================================================
@@ -29,20 +29,18 @@
 #ifdef CONFIG_HD64465
 #include <asm/hd64465.h>
 
-#define STD_SERIAL_PORT_DEFNS                   \
+#define SERIAL_PORT_DFNS                   \
         /* UART CLK   PORT IRQ     FLAGS        */                      \
         { 0, BASE_BAUD, 0x3F8, HD64465_IRQ_UART, STD_COM_FLAGS }  /* ttyS0 */
 
 #else
 
-#define STD_SERIAL_PORT_DEFNS			\
+#define SERIAL_PORT_DFNS			\
 	/* UART CLK   PORT IRQ     FLAGS        */			\
 	{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS },	/* ttyS0 */	\
 	{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }	/* ttyS1 */
 
 #endif
 
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
 #endif
 #endif /* _ASM_SERIAL_H */
include/asm-sh64/serial.h (mode:100644) +1 -3
Index: include/asm-sh64/serial.h
===================================================================
@@ -20,13 +20,11 @@
 
 #define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF | ASYNC_SKIP_TEST)
 
-#define STD_SERIAL_PORT_DEFNS			\
+#define SERIAL_PORT_DFNS			\
 	/* UART CLK   PORT IRQ     FLAGS        */			\
 	{ 0, BASE_BAUD, 0x3F8, 4, STD_COM_FLAGS },	/* ttyS0 */	\
 	{ 0, BASE_BAUD, 0x2F8, 3, STD_COM_FLAGS }	/* ttyS1 */
 
-#define SERIAL_PORT_DFNS STD_SERIAL_PORT_DEFNS
-
 /* XXX: This should be moved ino irq.h */
 #define irq_cannonicalize(x) (x)
 
include/asm-x86_64/serial.h (mode:100644) +1 -101

110 lines not on this page · raw message