arm: how to operate leds on zaurus?
Subsystems (2)
Hi!
2.6.12-rc5 (and newer) does not boot on sharp zaurus sl-5500. It blinks with green led, fast; what does it mean? I'd like to verify if it at least reaches .c code in setup.c. I inserted this code at begining of setup.c:674...
#define locomo_writel(val,addr) ({ *(volatile u16 *)(addr) = (val); })
#define LOCOMO_LPT_TOFH 0x80 #define LOCOMO_LED 0xe8 #define LOCOMO_LPT0 0x00
locomo_writel(LOCOMO_LPT_TOFH, LOCOMO_LPT0 + LOCOMO_LED);
...but that does not seem to do a trick -- it only breaks the boot :-( (do I need to add some kind of IO_BASE?).
Pavel
Signature · 1 line
teflon -- maybe it is a trademark, but it should not be.
Quoted 7 lines · Pavel Machek
Hi!
2.6.12-rc5 (and newer) does not boot on sharp zaurus sl-5500. It blinks with green led, fast; what does it mean? I'd like to verify if it at least reaches .c code in
setup.c. I inserted this code at begining of setup.c:674...
Quoted 8 lines
#define
locomo_writel(val,addr)({ *(volatile u16 *)(addr) = (val); })#define LOCOMO_LPT_TOFH 0x80 #define LOCOMO_LED 0xe8 #define LOCOMO_LPT0 0x00locomo_writel(LOCOMO_LPT_TOFH, LOCOMO_LPT0 + LOCOMO_LED);...but that does not seem to do a trick -- it only breaks the boot :-(
Basically because you do not have access to IO during the early boot. The easiest debugging solution is to enable CONFIG_DEBUG_LL and throw a printascii(printk_buf) into printk.c, after vscnprintf. That might get you some boot messages through the serial port (if it's implemented it correctly.)
Signature · 3 lines
Russell King Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/ maintainer of: 2.6 Serial core
Hi!
Quoted 12 lines
Quoted 12 lines
2.6.12-rc5 (and newer) does not boot on sharp zaurus sl-5500. It blinks with green led, fast; what does it mean? I'd like to verify if it at least reaches .c code in
setup.c. I inserted this code at begining of setup.c:674...#define
locomo_writel(val,addr)({ *(volatile u16 *)(addr) = (val); })#define LOCOMO_LPT_TOFH 0x80 #define LOCOMO_LED 0xe8 #define LOCOMO_LPT0 0x00locomo_writel(LOCOMO_LPT_TOFH, LOCOMO_LPT0 + LOCOMO_LED);
Quoted 7 lines
Quoted 1 line
...but that does not seem to do a trick -- it only breaks the boot :-(
Basically because you do not have access to IO during the early boot. The easiest debugging solution is to enable
CONFIG_DEBUG_LLand throw aprintascii(printk_buf)intoprintk.c, after vscnprintf. That might get you some boot messages through the serial port (if it's implemented it correctly.)
I'm afraid I do not have serial cable :-(. I'll try to get one [erik, do you have one you don't need?], but zaurus has "little" nonstandard connector.
Would code above work if executed later?
Pavel
Signature · 1 line
teflon -- maybe it is a trademark, but it should not be.
Quoted 20 lines
Quoted 12 lines
Quoted 12 lines
2.6.12-rc5 (and newer) does not boot on sharp zaurus sl-5500. It blinks with green led, fast; what does it mean? I'd like to verify if it at least reaches .c code in
setup.c. I inserted this code at begining of setup.c:674...#define
locomo_writel(val,addr)({ *(volatile u16 *)(addr) = (val); })#define LOCOMO_LPT_TOFH 0x80 #define LOCOMO_LED 0xe8 #define LOCOMO_LPT0 0x00locomo_writel(LOCOMO_LPT_TOFH, LOCOMO_LPT0 + LOCOMO_LED);Quoted 7 lines
Quoted 1 line
...but that does not seem to do a trick -- it only breaks the boot :-(
Basically because you do not have access to IO during the early boot. The easiest debugging solution is to enable
CONFIG_DEBUG_LLand throw aprintascii(printk_buf)intoprintk.c, after vscnprintf. That might get you some boot messages through the serial port (if it's implemented it correctly.)
Quoted 3 lines
I'm afraid I do not have serial cable :-(. I'll try to get one [erik, do you have one you don't need?], but zaurus has "little" nonstandard connector.
I am sorry, I sold my SL-5500 before a few days. For build serial cable you need: connector, two negator gates (CMOS 4011, 74HCT00 ...), MAX232 (RS232 voltage level convertor) and DB9 serial connector. Circuit is a bit strange, because Zaurus have inverted TxD and RxD signals. All parts I can buy in .cz without problems, only connector I can't.
Yokotashi
Quoted 6 lines
Would code above work if executed later?
PavelSignature · 1 line
teflon -- maybe it is a trademark, but it should not be.
Quoted 5 lines · Pavel Machek
I'm afraid I do not have serial cable :-(. I'll try to get one [erik, do you have one you don't need?], but zaurus has "little" nonstandard connector.
Would code above work if executed later?
If done after the IO mappings are setup. That will be after paging_init() has been called.
Signature · 3 lines
Russell King Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/ maintainer of: 2.6 Serial core
Quoted 12 lines · Pavel Machek
Hi!
2.6.12-rc5 (and newer) does not boot on sharp zaurus sl-5500. It blinks with green led, fast; what does it mean? I'd like to verify if it at least reaches .c code in
setup.c. I inserted this code at begining of setup.c:674...#define
locomo_writel(val,addr)({ *(volatile u16 *)(addr) = (val); })#define LOCOMO_LPT_TOFH 0x80 #define LOCOMO_LED 0xe8 #define LOCOMO_LPT0 0x00
Quoted 5 lines
locomo_writel(LOCOMO_LPT_TOFH, LOCOMO_LPT0 + LOCOMO_LED);...but that does not seem to do a trick -- it only breaks the boot :-( (do I need to add some kind of
IO_BASE?).
Pavel
No, that won't work.
As Russell said, there are problems accessing memory before the io maps have been set up correctly. You can see the patch
http://www.cs.wisc.edu/~lenz/zaurus/files/2.6.12-rc5/lenz-03-leds-2.6.12-rc5.patch
need scroll near the bottom in file locomo.c to see how the led gets set. You won't actually be able to know where in memory that space is mapped because we call ioremap, and won't be able to access the locomo stuff until device_initcall.
WARNING: Horrible hack! Ugly, ugly, ugly! First read and understand the warning at
http://lists.arm.linux.org.uk/pipermail/linux-arm-kernel/2002-January/006730.html
Having said that, either before the MMU has been activated or before the ioremap() has been called, it is sometimes possible to access the LEDs at the physical addresses they are located at. This may or may not work, might not always work, etc... but it can help as a last resort. On the SL5500, the physical address of the start of the locomo chip is 0x40000000, and the leds are at an offset of 0xe8, so something like volatile u16 *led = (volatile u16 *)0x400000e8;
*led = 0x80;
As the above email says, this is not guarenteed to work at all, will fail at some point in the boot process, but is something you can try.
That said, I am aware that recent kernel versions have broken the boot on collie, but haven't looked at the problem in detail (i.e. tried doing a binary search between known working versions and broken ones to see the patch that introduced the problem). I have been working on the SL5600 recently.
John
Sharp Zaurus sl-5500 broken in 2.6.12
Hi!
...and that's well known; but now I did some back tracking, and 2.6.12-rc1 works, 2.6.12-rc2 does *not* and 2.6.12-rc2 with arm changes reverted works. I'll play a bit more.
Pavel
Signature · 1 line
Boycott Kodak -- for their patent abuse against Java.
Re: Sharp Zaurus sl-5500 broken in 2.6.12
Hi!
Quoted 3 lines
...and that's well known; but now I did some back tracking, and 2.6.12-rc1 works, 2.6.12-rc2 does *not* and 2.6.12-rc2 with arm changes reverted works. I'll play a bit more.
This fixes at least one break-the-boot bug in -rc2...
Pavel
arch/arm/mach-sa1100/collie.c +1 -1
@@ -235,7 +235,7 @@sa11x0_set_flash_data (&collie_flash_data, collie_flash_resources,ARRAY_SIZE (collie_flash_resources)); -sharpsl_save_param (); +// sharpsl_save_param(); }static struct map_desc collie_io_desc[]__initdata = {
Signature · 1 line
teflon -- maybe it is a trademark, but it should not be.
Re: Sharp Zaurus sl-5500 broken in 2.6.12
Quoted 13 lines · Pavel Machek
Hi!
Quoted 3 lines
...and that's well known; but now I did some back tracking, and 2.6.12-rc1 works, 2.6.12-rc2 does *not* and 2.6.12-rc2 with arm changes reverted works. I'll play a bit more.
This fixes at least one break-the-boot bug in -rc2...
Pavel
arch/arm/mach-sa1100/collie.c line 241
Quoted 8 lines
arch/arm/mach-sa1100/collie.c +1
-1@@ -235,7 +235,7 @@sa11x0_set_flash_data (&collie_flash_data, collie_flash_resources,ARRAY_SIZE (collie_flash_resources)); -sharpsl_save_param (); +// sharpsl_save_param(); }static struct map_desc collie_io_desc[]__initdata = {
Could you check this wasn't caused by this typo please:
http://www.rpsys.net/openzaurus/patches/collie_typofix-r0.patch
(this has been fixed in recent kernels)
Cheers,
Richard
Re: Sharp Zaurus sl-5500 broken in 2.6.12
Hi!
Quoted 18 lines
Quoted 18 lines
Quoted 3 lines
...and that's well known; but now I did some back tracking, and 2.6.12-rc1 works, 2.6.12-rc2 does *not* and 2.6.12-rc2 with arm changes reverted works. I'll play a bit more.
This fixes at least one break-the-boot bug in -rc2...
Pavel
arch/arm/mach-sa1100/collie.c +1
-1@@ -235,7 +235,7 @@sa11x0_set_flash_data (&collie_flash_data, collie_flash_resources,ARRAY_SIZE (collie_flash_resources)); -sharpsl_save_param (); +// sharpsl_save_param(); }
Quoted 7 lines
arch/arm/mach-sa1100/collie.c line 241
Quoted 1 line
arch/arm/mach-sa1100/collie.c +0
-0static struct map_desc collie_io_desc[]__initdata = {Could you check this wasn't caused by this typo please:
http://www.rpsys.net/openzaurus/patches/collie_typofix-r0.patch
(this has been fixed in recent kernels)
Oops, you are right, it is now fixed. I screwed up some config or something... It works now.
BTW is there some place where I can find modifications Sharp did to mainline 2.4 kernel?
Pavel
Signature · 1 line
Boycott Kodak -- for their patent abuse against Java.
Re: Sharp Zaurus sl-5500 broken in 2.6.12
Quoted 2 lines · Pavel Machek
BTW is there some place where I can find modifications Sharp did to mainline 2.4 kernel?
First, sharp's modifications were not to the base 2.4 kernels, but you first applied the rmk patch and then the pxa patch.
I have tried to split up the huge patch
http://www.cs.wisc.edu/~lenz/zaurus/files/slc860-patches.tar.bz2
But the original patch is hosted around here somewhere. To find where, take a look inside the .bb file inside OE... you should be able to check out openembedded (from www.openembedded.org) and find the .bb file that builds the kernel.
John