Skip to contentSkip to conversation

2.6.8 -> 2.6.11 (+ata-dev patch) -- HDD is always on

DISCUSSION Yaroslav Halchenko 4 participants 7 messages Jul 29, 2005 – Jul 31, 2005

lore
Share & tools
lore
#0 lore raw

I've been running debian stable with 2.6.8 kernel but due to recent failure of the SATA harddrive I've decided to upgrade to 2.6.11 + libata patch (2.6.11-libata-dev1.patch.gz) and recent smartmontools

After everything worked out and I decided to rest in piece but I've found that HDD LED light nomater what. It seems to turn off during BIOS checks and then kicks in 1-2 secs after kernel starts booting. No prominent harddrive activity noise can be heard but this drive is quite silent so it is hard to say.

SATA drivers were compiled in the kernel to don't mess with initrd.

QUESTION:

LED constantly ON - does it signal about a problem or may be just that some status bit is hanging? Should I worry and try differen kernel version?

YIKES: ran hddtemp /dev/sda and whole box hanged... SysRq keys - no effect... heh heh... reboot -> nothing in logs

Detailed information on the system and drives (outputs of smartctl -a) can be found

http://www.onerussian.com/Linux/bugs/ata/

Thank you in advance for ideas

P.S. was ata-dev patch incorporated in recent kernel versions so I could use SMART with vanilla kernel?

Signature · 3 lines
Yaroslav Halchenko
  Graduate Student  CS Dept. UNM,  ABQ
        Linux User  175555
#1 lore raw
Quoted 9 lines · Yaroslav Halchenko

I've been running debian stable with 2.6.8 kernel but due to recent failure of the SATA harddrive I've decided to upgrade to 2.6.11 + libata patch (2.6.11-libata-dev1.patch.gz) and recent smartmontools

After everything worked out and I decided to rest in piece but I've found that HDD LED light nomater what. It seems to turn off during BIOS checks and then kicks in 1-2 secs after kernel starts booting. No prominent harddrive activity noise can be heard but this drive is quite silent so it is hard to say.

Does this happen in unpatched 2.6.12.3 or 2.6.13-rc4?

Quoted 11 lines

QUESTION:

LED constantly ON - does it signal about a problem or may be just that some status bit is hanging? Should I worry and try differen kernel version?

YIKES: ran hddtemp /dev/sda and whole box hanged... SysRq keys - no effect... heh heh... reboot -> nothing in logs

P.S. was ata-dev patch incorporated in recent kernel versions so I could use SMART with vanilla kernel?

This is one of the reasons why SMART support is not yet in the mainline kernel!

Jeff

#2 lore raw
Quoted 1 line · Jeff Garzik

Does this happen in unpatched 2.6.12.3 or 2.6.13-rc4?

just tried unpatched 2.6.12.3.
The Box stalls booting with
"Uncompressing Linux... Ok, booting the kernel.
_"

interesting though that led hdd light is off at first, blinks few times, and 1-2 secs after it stalls with above message - it gets its steady green light on.

Could I screw up some NEW kernel configuration parameters when pulling config from 2.6.8 from Debian? I don't know :-/

I will try 2.6.13-rc4 now... heh heh

Signature · 3 lines
Yaroslav Halchenko
  Graduate Student  CS Dept. UNM,  ABQ
        Linux User  175555
#3 lore raw

Damn me - sorry for the misinformation... I've compiled the kernel without Debian-loved initrd image...

so I've booted 2.6.12.3 -- LED light is on - so I bet no blame on libata patch, although I've mentioned few patches from that patch migrated into the mainstream kernel.

Any ideas on which next step to take? 2.6.13-rc4? or vanilla 2.6.11?

Quoted 15 lines · Yaroslav Halchenko
Quoted 1 line · Jeff Garzik

Does this happen in unpatched 2.6.12.3 or 2.6.13-rc4?

just tried unpatched 2.6.12.3.
The Box stalls booting with
"Uncompressing Linux... Ok, booting the kernel.
_"

interesting though that led hdd light is off at first, blinks few times, and 1-2 secs after it stalls with above message - it gets its steady green light on.

Could I screw up some NEW kernel configuration parameters when pulling config from 2.6.8 from Debian? I don't know :-/

I will try 2.6.13-rc4 now... heh heh

Signature · 5 lines
Yaroslav Halchenko
Research Assistant, Psychology Department, Rutgers-Newark
Office: (973) 353-5440x263 | FWD: 82823 | Fax: (973) 353-1171
        101 Warren Str, Smith Hall, Rm 4-105, Newark NJ 07105
Student  Ph.D. @ CS Dept. NJIT
#4 lore raw
Quoted 1 line
Quoted 1 line
Quoted 1 line

Does this happen in unpatched 2.6.12.3 or 2.6.13-rc4?

tried clear 2.6.11 ( with no libata patch -- light is on :-( )

/booted 2.6.8 Debian kernel -- everything is fine, but no libata-dev patch for SATA makes me wonder if you should try 2.6.13-rc4/

once again -- details of the system can be found
http://www.onerussian.com/Linux/bugs/ata/

Signature · 5 lines
Yaroslav Halchenko
Research Assistant, Psychology Department, Rutgers-Newark
Office: (973) 353-5440x263 | FWD: 82823 | Fax: (973) 353-1171
        101 Warren Str, Smith Hall, Rm 4-105, Newark NJ 07105
Student  Ph.D. @ CS Dept. NJIT
#5 lore raw
In reply to Jeff Garzik
Quoted 1 line · Jeff Garzik

Does this happen in unpatched 2.6.12.3 or 2.6.13-rc4?

now tested both of them -- light is constantly on in both.

does the HDD LED always signals about hardware activity or it can just be sticky and not reset properly?

is there libata-dev patch for 2.6.8 kernel which seems to be running fine so I might just patch it to get SATA SMART?

Thank you in advance for the feedback

Signature · 5 lines
Yaroslav Halchenko
Research Assistant, Psychology Department, Rutgers-Newark
Office: (973) 353-5440x263 | FWD: 82823 | Fax: (973) 353-1171
        101 Warren Str, Smith Hall, Rm 4-105, Newark NJ 07105
Student  Ph.D. @ CS Dept. NJIT
#6 lore raw
Quoted 8 lines · Yaroslav Halchenko
Quoted 1 line · Jeff Garzik

Does this happen in unpatched 2.6.12.3 or 2.6.13-rc4?

now tested both of them -- light is constantly on in both.

does the HDD LED always signals about hardware activity or it can just be sticky and not reset properly?

As long as the system otherwise functions properly, the LED is the least of our worries...

Jeff