Skip to contentSkip to conversation

Logitech Quickcam Express USB Address Aquisition Issues

DISCUSSION Chris White 7 participants 12 messages Aug 7, 2005 – Aug 8, 2005 1 message not in the archive

lore
Share & tools
lore
#0 lore raw

[Pre Note: please CC me all responses, thanks]

Currently, I have a Logitech Quickcam Express webcamera. Unfortunately, it seems to have issues getting assigned an address. I quote the following from dmesg:

usb 1-1.1: new full speed USB device using ehci_hcd and address 11 usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: new full speed USB device using ehci_hcd and address 12 usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: new full speed USB device using ehci_hcd and address 13 usb 1-1.1: device not accepting address 13, error -32 usb 1-1.1: new full speed USB device using ehci_hcd and address 14 usb 1-1.1: device not accepting address 14, error -32

As far as the host goes, I have the following USB hosts:

0000:00:11.0 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.1 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.2 USB Controller: NEC Corporation USB 2.0 (rev 04)

The first is my builtin Intel USB controller, the second is one belkin USB 1.0 card, and another 2.0 card. I've tried it in all three just to verify one of my hosts wasn't broken. Considering my printer works with it, as well as my scanner, I'm sort of thinking that's not an issue.

I searched up google a bit and recieved some warnings about acpi causing problems, so I disabled that, but was still unsucessful in getting that to work. Please let me know if any other information is required. Thanks ahead of time.

Chris White

#1 lore raw
Quoted 29 lines · Chris White

[Pre Note: please CC me all responses, thanks]

Currently, I have a Logitech Quickcam Express webcamera. Unfortunately, it seems to have issues getting assigned an address. I quote the following from dmesg:

usb 1-1.1: new full speed USB device using ehci_hcd and address 11 usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: new full speed USB device using ehci_hcd and address 12 usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: new full speed USB device using ehci_hcd and address 13 usb 1-1.1: device not accepting address 13, error -32 usb 1-1.1: new full speed USB device using ehci_hcd and address 14 usb 1-1.1: device not accepting address 14, error -32

As far as the host goes, I have the following USB hosts:

0000:00:11.0 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.1 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.2 USB Controller: NEC Corporation USB 2.0 (rev 04)

The first is my builtin Intel USB controller, the second is one belkin USB 1.0 card, and another 2.0 card. I've tried it in all three just to verify one of my hosts wasn't broken. Considering my printer works with it, as well as my scanner, I'm sort of thinking that's not an issue.

Quoted 5 lines

I searched up google a bit and recieved some warnings about acpi causing problems, so I disabled that, but was still unsucessful in getting that to work. Please let me know if any other information is required. Thanks ahead of time.

(Added linux-usb-devel)

Which kernel version?

Did it work OK under a previous kernel version? If so, which?

#2 lore raw
Quoted 1 line

Which kernel version?

Yes, I was just about to slap myself for fogetting that, it's under greg-kh's 2.6.12.13 git repository sources.

Quoted 1 line

Did it work OK under a previous kernel version? If so, which?

I haven't attempted that, but I'll probably give a 2.6.9/2.4 series kernel a shot later on tommorow night.

Chris White

#4 lore raw
In reply to a message not in the archive
Quoted 4 lines · Chris White
Quoted 1 line

Did it work OK under a previous kernel version? If so, which?

I haven't attempted that, but I'll probably give a 2.6.9/2.4 series kernel a shot later on tommorow night.

Does that thing work with Windows?

I strongly suspect that it's simply broken at this point.

-- Pete

#6 lore raw
In reply to Chris White
Quoted 7 lines · Chris White

As far as the host goes, I have the following USB hosts:

0000:00:11.0 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.1 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.2 USB Controller: NEC Corporation USB 2.0 (rev 04)

The first is my builtin Intel USB controller, the second is one belkin USB 1.0 card, and another 2.0 card. I've tried it in all three just to verify one of my hosts wasn't broken. Considering my printer works with it, as well as my scanner, I'm sort of thinking that's not an issue.

It looks like one add-on USB 2.0 card with NEC chip which is backward compatible with USB 1.0. No Intel here.

Signature · 1 line
Ondrej Zary
#7 lore raw
In reply to Chris White
Quoted 21 lines · Chris White

[Pre Note: please CC me all responses, thanks]

Currently, I have a Logitech Quickcam Express webcamera. Unfortunately, it seems to have issues getting assigned an address. I quote the following from dmesg:

usb 1-1.1: new full speed USB device using ehci_hcd and address 11 usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: new full speed USB device using ehci_hcd and address 12 usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: device descriptor read/64, error -32
usb 1-1.1: new full speed USB device using ehci_hcd and address 13 usb 1-1.1: device not accepting address 13, error -32 usb 1-1.1: new full speed USB device using ehci_hcd and address 14 usb 1-1.1: device not accepting address 14, error -32

As far as the host goes, I have the following USB hosts:

0000:00:11.0 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.1 USB Controller: NEC Corporation USB (rev 43) 0000:00:11.2 USB Controller: NEC Corporation USB 2.0 (rev 04)

Quoted 5 lines

The first is my builtin Intel USB controller, the second is one belkin USB 1.0 card, and another 2.0 card. I've tried it in all three just to verify one of my hosts wasn't broken. Considering my printer works with it, as well as my scanner, I'm sort of thinking that's not an issue.

I searched up google a bit and recieved some warnings about acpi causing problems, so I disabled that, but was still unsucessful in getting that to work. Please let me know if any other information is required. Thanks ahead of time.

Chris White

does the drivers for the Phillips web cams come back to the kernel? because i thought that it was taken out...

http://www.smcc.demon.nl/webcam/

check this site and see if your cam was one of the cams that supported from the driver that discontinue... so if is supported by this driver, download and install it... it works i try it with my cam ;)

#8 lore raw

On Sunday 07 Aug 2005 12:36, christos gentsis wrote:
[snip]

Quoted 8 lines
Quoted 7 lines

I searched up google a bit and recieved some warnings about acpi causing problems, so I disabled that, but was still unsucessful in getting that to work. Please let me know if any other information is required. Thanks ahead of time.

Chris White

Quoted 9 lines

does the drivers for the Phillips web cams come back to the kernel? because i thought that it was taken out...

http://www.smcc.demon.nl/webcam/

check this site and see if your cam was one of the cams that supported from the driver that discontinue... so if is supported by this driver, download and install it... it works i try it with my cam ;)

The in-kernel pwc driver doesn't work for me either. I highly recommend you try the above if this turns out to not be a hardware fault.

Signature · 6 lines
Cheers,
Alistair.

'No sense being pessimistic, it probably wouldn't work anyway.'
Third year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.
#9 lore raw
Quoted 13 lines · Alistair John Strachan

On Sunday 07 Aug 2005 12:36, christos gentsis wrote:
[snip]

Quoted 10 lines
Quoted 6 lines

I searched up google a bit and recieved some warnings about acpi causing problems, so I disabled that, but was still unsucessful in getting that to work. Please let me know if any other information is required. Thanks ahead of time.

Chris White

does the drivers for the Phillips web cams come back to the kernel? because i thought that it was taken out...

Quoted 8 lines
Quoted 5 lines

http://www.smcc.demon.nl/webcam/

check this site and see if your cam was one of the cams that supported from the driver that discontinue... so if is supported by this driver, download and install it... it works i try it with my cam ;)

The in-kernel pwc driver doesn't work for me either. I highly recommend you try the above if this turns out to not be a hardware fault.

Sorry, I didn't even check the link. Try the driver from:

http://www.saillard.org/linux/pwc/

Which seems to work better.

Signature · 6 lines
Cheers,
Alistair.

'No sense being pessimistic, it probably wouldn't work anyway.'
Third year Computer Science undergraduate.
1F2 55 South Clerk Street, Edinburgh, UK.
#10 lore raw
Quoted 9 lines

Sorry, I didn't even check the link. Try the driver from:

http://www.saillard.org/linux/pwc/

Which seems to work better.

Signature · 2 lines
Cheers,
Alistair.

Err, mine's a logitech camera, why is everyone recommending philips drivers :P?

Chris White

#11 lore raw
Quoted 8 lines · Chris White
Quoted 5 lines

Sorry, I didn't even check the link. Try the driver from:

http://www.saillard.org/linux/pwc/

Which seems to work better.

Err, mine's a logitech camera, why is everyone recommending philips drivers :P?

Because many of the Logitech cameras are based on the Philips
chipset.

Hugo.

Signature · 3 lines
=== Hugo Mills: hugo@... carfax.org.uk | darksatanic.net | lug.org.uk ===
  PGP key: 1C335860 from wwwkeys.eu.pgp.net or http://www.carfax.org.uk
           --- All hope abandon,  Ye who press Enter here. ---           
#12 lore raw
In reply to Chris White
Quoted 4 lines · Chris White

Err, mine's a logitech camera, why is everyone recommending philips drivers :P?

Chris White

what happens with the most of the computer peripherals the company that sell it is different with the company that produce it... in this case philips sell the ship for the cameras to other companies and logitech use that chip. in the website say which cameras are based to the philips chip

#5 lore raw
In reply to Pete Zaitcev
Quoted 6 lines

Does that thing work with Windows?

I strongly suspect that it's simply broken at this point.

-- Pete

And that is the final answer for $14,000. Looks like I got Yet Another Large Paperweight(tm) to deal with. Yup, this thing is broken. I tried it on my dad's machine today, and Windows chucked the thing out as invalid format right away. Oh well, maybe I should enroll in an electronics class and fix it myself.

Chris White